Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
You should also double-check the length of your all-thread rods. I'd dummy one up and try it out before cutting all of them. It needs to be just long enough to catch a couple of threads and snug down without punching out through the cap nut. The actual "cap" portion of cap nuts is fairly thin, and if the all-thread is even a bit too long it will punch through the end when you snug it up.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Since this project contains two different finishes it is best to do the finishing before going any farther in the assembly process. We wanted to match the Pottery Barn finish as closely as possible so we went with the charcoal Chalked ultra matte paint from Rust-Oleum. I love the thick textured look of this paint. To brighten it up a bit and give it a cool look we decided to wax it with a Johnson Paste wax and a lot of elbow grease.
Looks very opulent especially in a living area where the family likes to unwind with each other. These book-cases have ample storage space for books, housing shelves at multiple levels for decor items too. The middle portion of the bookcase if left blank can be used as a space for the television unit, serving as a complete entertainment area in the house.
Just for the record, a jointer and planer are not from the ICDT kit – the philosophy on that column is, indeed, beginner AND basic (hence the Workmate). The tools we suggest in the ICDT manual are for those who are working at a kitchen table or in a backyard; the tools the editors would recommend for someone who is quite sure he or she wants to pursue serious furniture making would be rather different.
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.
Apply carpenter's glue to the dadoes, set the plywood shelves in place and secure them with 1 5/8-in. drywall screws [ 3 ]. Since the bookcase has no back, you need to install a wood strip, or hanging rail, to screw each case to the wall. Cut the rail from a 1 x 3 or 1 x 4 to fit between the two case sides. Position it directly above the case top, and attach it to the case sides with glue and screws.
It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.
It wasn't until the end of the eighteenth century when the first woodworking machine was patented. Some of the basic principles of the earliest woodworking machine tools are still in use today, but the new machines are faster, more powerful, and easier to use than previous generations. We carry a full range of stationary woodworking machines including table saws, miter saws, band saws, drill presses, mortisers, shapers, planers and more. If you have any questions or need help finding what you need, give us a call or email and we'll assist you in finding the right woodworking machine.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ... More + Product Details Close
This is that rare two-for-one deal in which two tools have been effectively made one. The stationary belt sander uses a closed loop of paper that travels at speed around a pair of cylindrical drums. One drum is driven by an electric motor, the other is spring-loaded to maintain belt tension. Powered by the same motor, the stationary disk sander uses sanding disks that spin on a backing plate.
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
After investing a number of weekends building a nice table or chest, how are you going to finish it? Finishes beautify and protect the piece you’ve worked so hard to build so don’t cop out and do the “rub it with oil” thing. There are so many beautiful finishes that become second nature to work with. I use shellac 99% of the time. Once you get the feel down, it’s really quick to apply, very forgiving, easily repairable, and you never have to clean a brush (because it re-softens in alcohol)! There are other varnishes that provide good protection for outdoor use as well. I recommend picking up a good starter book, like Jeff Jewitt’s Hand Applied Finishes. It is simple and straightforward, without getting too far into minutiae.
To give you an idea about the different bookshelf plans available,this guide presents you 17 simple but alluring bookcase designs to choose from. The designs are not only in a wide array of sizes and styles but they are also inexpensive to build and will fulfil your home space. So be sure to go through all of them to find the best one for your room.
Teds Woodworking is a big collection of woodworking plans and all of these are well organized and categorized so that you find what you are looking for fast. These woodworking plans include bed plans, table and chair plans, furniture plans, shed plans, bird house plans and many more. Each of these woodworking plans come with full comprehensive instructions as well as diagrams. You will be able to see, what it is you want to do. The program also includes 150 training videos, so you can see and learn how things should be done. You will be able to see the complete pieces that you need to build and learn how to fit them together. The diagrams are used by many individuals as they go through each part of the process.
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.