There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
The knotty pine bookcase parts are all standard dimensional lumber that you can find at any home center. We joined the shelves and legs with biscuits. If you don’t own a biscuit joiner but still want to build this project, you can simply nail or screw the parts together and fill the holes. We used a table saw to cut the 1-1/2-in. square legs from 2x4s and a router with a 45-degree chamfer bit to bevel the edge of the top. If you don’t have a table saw or router, you can just use stock 2x2s for the legs and leave the edge of the top square.
Keeping your house clean and well-sorted is probably one of the trickiest tasks, especially if you are one of those people who have more books than clothes and shoes combined. Each of your books is priceless and you want to preserve them in the best condition possible. But it is not always so easy, especially if you do not have a proper bookshelf. Now bookshelves do not come cheap, be it a simple plywood one or an ornate wooden case. So, here are forty simple yet trendy DIY bookshelves for you and your books.
11. Other necessary skills: Each woodworker should have a basic knowledge of metalworking. Although most of the home furniture is made out of wood, in this category you may occasionally find some projects made out of metal, or the wooden furniture projects that have a decorative metal parts or fasteners. In our opinion, the combination of wood and wrought iron makes the most beautiful furniture.
thank you, thank you, thank you!! the lumber that i had in the garage wasn't exactly what your plans called for (2x4s and 1x10s), so i adjusted the length of the all thread to accommodate the depth. also, one of my 2x4s was kind of wonky and i was worried it would jeopardize the stability of the set - but it's totally solid! the shelves are level and aren't going anywhere!! :) (i threw all of my body weight against it, and it's totally solid!) it's approx. 4' wide by 7.5' tall.
Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.
I always try to ask my students why they have come to my school. The standard answer is, "I wanted to learn the right way," but frequently the answer is "that I sit in front of a computer all day and don't feel like I do anything at all." Or simply, they are bored with sitting at home every night. These are the people who are really fun to have in class. They have no preconceived notions, no bad habits to break and they usually really appreciate whatever they have made. Many of them go on to make some new friends at the school. Through the years, I have seen many make plans to take another class "if my buddy is going to do it, too."
Break down plywood Following the cutting diagram, crosscut plywood along the line marked “first cut”. Take the smaller of the two rip 3/4″ plywood according to diagram and cut list. For safety and easier handling, use a circular saw with a good quality blade (following a straight edge guide for a straight cut) for first cross-cut on plywood. If you are not confident in your circular saw’s ability to cut straight lines with no tear out, leave yourself 1/4″ of extra material (there is enough extra material in a 4′ x 8′ sheet of plywood to do this) and make your final cuts on the table saw.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
All things considered, the easiest and most practical way to plane a piece of unmilled wood is to use a router. You can pick up a halfway decent router fairly inexpensively, and the good thing about investing in one is that there’s truly no limit to what you can do with it - planing a piece of wood is just one of a million different things a router can be used for.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.