Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
There are several ways to complete this task, including pocket screws, brads or biscuits. I have used all of these methods, but my preference is biscuits, as they provide adequate strength, excellent alignment, and ease. I generally just place one biscuit in the center of each rail and stile, which provides alignment assistance while not being overly constraining when manual adjustments need to be made to achieve desired placement. After applying glue and biscuits, use lots of clamps to create a gap-free bond between the face frame and carcass.
I really like building difficult cabinets, laying them out, and assembling them. It really gives me a challenge to build something better each time, but the sanding and clean up are not my favorite aspects of this work; you better get used to it. And I wish I would have taken some business classes because the part of running a business is another element added to cabinet making.
Since this project contains two different finishes it is best to do the finishing before going any farther in the assembly process. We wanted to match the Pottery Barn finish as closely as possible so we went with the charcoal Chalked ultra matte paint from Rust-Oleum. I love the thick textured look of this paint. To brighten it up a bit and give it a cool look we decided to wax it with a Johnson Paste wax and a lot of elbow grease.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
The table saw is the center of most workshops; it is the largest and most imposing tool in the shop. While it is an important tool, one could claim that table saw need not be on this list. However, it is an important tool and shows that creating a shop is not a matter of just collecting hand tools. There are jobs that hand tools cannot do as well as tools like the table saw, especially when there is such a wide variety of blades which can be set up and changed for so many different applications. Table saws create straight and consistent cuts. When setting up a table saw for a cut, one needs to set the depth of the blade and adjust the fence according to the width desired.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.

I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
!function(n,t){function r(e,n){return Object.prototype.hasOwnProperty.call(e,n)}function i(e){return void 0===e}if(n){var o={},s=n.TraceKit,a=[].slice,u="?";o.noConflict=function(){return n.TraceKit=s,o},o.wrap=function(e){function n(){try{return e.apply(this,arguments)}catch(e){throw o.report(e),e}}return n},o.report=function(){function e(e){u(),h.push(e)}function t(e){for(var n=h.length-1;n>=0;--n)h[n]===e&&h.splice(n,1)}function i(e,n){var t=null;if(!n||o.collectWindowErrors){for(var i in h)if(r(h,i))try{h[i].apply(null,[e].concat(a.call(arguments,2)))}catch(e){t=e}if(t)throw t}}function s(e,n,t,r,s){var a=null;if(w)o.computeStackTrace.augmentStackTraceWithInitialElement(w,n,t,e),l();else if(s)a=o.computeStackTrace(s),i(a,!0);else{var u={url:n,line:t,column:r};u.func=o.computeStackTrace.guessFunctionName(u.url,u.line),u.context=o.computeStackTrace.gatherContext(u.url,u.line),a={mode:"onerror",message:e,stack:[u]},i(a,!0)}return!!f&&f.apply(this,arguments)}function u(){!0!==d&&(f=n.onerror,n.onerror=s,d=!0)}function l(){var e=w,n=p;p=null,w=null,m=null,i.apply(null,[e,!1].concat(n))}function c(e){if(w){if(m===e)return;l()}var t=o.computeStackTrace(e);throw w=t,m=e,p=a.call(arguments,1),n.setTimeout(function(){m===e&&l()},t.incomplete?2e3:0),e}var f,d,h=[],p=null,m=null,w=null;return c.subscribe=e,c.unsubscribe=t,c}(),o.computeStackTrace=function(){function e(e){if(!o.remoteFetching)return"";try{var t=function(){try{return new n.XMLHttpRequest}catch(e){return new n.ActiveXObject("Microsoft.XMLHTTP")}},r=t();return r.open("GET",e,!1),r.send(""),r.responseText}catch(e){return""}}function t(t){if("string"!=typeof t)return[];if(!r(j,t)){var i="",o="";try{o=n.document.domain}catch(e){}var s=/(.*)\:\/\/([^:\/]+)([:\d]*)\/{0,1}([\s\S]*)/.exec(t);s&&s[2]===o&&(i=e(t)),j[t]=i?i.split("\n"):[]}return j[t]}function s(e,n){var r,o=/function ([^(]*)\(([^)]*)\)/,s=/['"]?([0-9A-Za-z$_]+)['"]?\s*[:=]\s*(function|eval|new Function)/,a="",l=10,c=t(e);if(!c.length)return u;for(var f=0;f0?s:null}function l(e){return e.replace(/[\-\[\]{}()*+?.,\\\^$|#]/g,"\\$&")}function c(e){return l(e).replace("<","(?:<|<)").replace(">","(?:>|>)").replace("&","(?:&|&)").replace('"','(?:"|")').replace(/\s+/g,"\\s+")}function f(e,n){for(var r,i,o=0,s=n.length;or&&(i=s.exec(o[r]))?i.index:null}function h(e){if(!i(n&&n.document)){for(var t,r,o,s,a=[n.location.href],u=n.document.getElementsByTagName("script"),d=""+e,h=/^function(?:\s+([\w$]+))?\s*\(([\w\s,]*)\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,p=/^function on([\w$]+)\s*\(event\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,m=0;m]+)>|([^\)]+))\((.*)\))? in (.*):\s*$/i,o=n.split("\n"),u=[],l=0;l=0&&(g.line=v+x.substring(0,j).split("\n").length)}}}else if(o=d.exec(i[y])){var _=n.location.href.replace(/#.*$/,""),T=new RegExp(c(i[y+1])),E=f(T,[_]);g={url:_,func:"",args:[],line:E?E.line:o[1],column:null}}if(g){g.func||(g.func=s(g.url,g.line));var k=a(g.url,g.line),A=k?k[Math.floor(k.length/2)]:null;k&&A.replace(/^\s*/,"")===i[y+1].replace(/^\s*/,"")?g.context=k:g.context=[i[y+1]],h.push(g)}}return h.length?{mode:"multiline",name:e.name,message:i[0],stack:h}:null}function y(e,n,t,r){var i={url:n,line:t};if(i.url&&i.line){e.incomplete=!1,i.func||(i.func=s(i.url,i.line)),i.context||(i.context=a(i.url,i.line));var o=/ '([^']+)' /.exec(r);if(o&&(i.column=d(o[1],i.url,i.line)),e.stack.length>0&&e.stack[0].url===i.url){if(e.stack[0].line===i.line)return!1;if(!e.stack[0].line&&e.stack[0].func===i.func)return e.stack[0].line=i.line,e.stack[0].context=i.context,!1}return e.stack.unshift(i),e.partial=!0,!0}return e.incomplete=!0,!1}function g(e,n){for(var t,r,i,a=/function\s+([_$a-zA-Z\xA0-\uFFFF][_$a-zA-Z0-9\xA0-\uFFFF]*)?\s*\(/i,l=[],c={},f=!1,p=g.caller;p&&!f;p=p.caller)if(p!==v&&p!==o.report){if(r={url:null,func:u,args:[],line:null,column:null},p.name?r.func=p.name:(t=a.exec(p.toString()))&&(r.func=t[1]),"undefined"==typeof r.func)try{r.func=t.input.substring(0,t.input.indexOf("{"))}catch(e){}if(i=h(p)){r.url=i.url,r.line=i.line,r.func===u&&(r.func=s(r.url,r.line));var m=/ '([^']+)' /.exec(e.message||e.description);m&&(r.column=d(m[1],i.url,i.line))}c[""+p]?f=!0:c[""+p]=!0,l.push(r)}n&&l.splice(0,n);var w={mode:"callers",name:e.name,message:e.message,stack:l};return y(w,e.sourceURL||e.fileName,e.line||e.lineNumber,e.message||e.description),w}function v(e,n){var t=null;n=null==n?0:+n;try{if(t=m(e))return t}catch(e){if(x)throw e}try{if(t=p(e))return t}catch(e){if(x)throw e}try{if(t=w(e))return t}catch(e){if(x)throw e}try{if(t=g(e,n+1))return t}catch(e){if(x)throw e}return{mode:"failed"}}function b(e){e=1+(null==e?0:+e);try{throw new Error}catch(n){return v(n,e+1)}}var x=!1,j={};return v.augmentStackTraceWithInitialElement=y,v.guessFunctionName=s,v.gatherContext=a,v.ofCaller=b,v.getSource=t,v}(),o.extendToAsynchronousCallbacks=function(){var e=function(e){var t=n[e];n[e]=function(){var e=a.call(arguments),n=e[0];return"function"==typeof n&&(e[0]=o.wrap(n)),t.apply?t.apply(this,e):t(e[0],e[1])}};e("setTimeout"),e("setInterval")},o.remoteFetching||(o.remoteFetching=!0),o.collectWindowErrors||(o.collectWindowErrors=!0),(!o.linesOfContext||o.linesOfContext<1)&&(o.linesOfContext=11),void 0!==e&&e.exports&&n.module!==e?e.exports=o:"function"==typeof define&&define.amd?define("TraceKit",[],o):n.TraceKit=o}}("undefined"!=typeof window?window:global)},"./webpack-loaders/expose-loader/index.js?require!./shared/require-global.js":function(e,n,t){(function(n){e.exports=n.require=t("./shared/require-global.js")}).call(n,t("../../../lib/node_modules/webpack/buildin/global.js"))}});

This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
My parents have the space and Dad has the tools -- a drill press, forstner bits and a long workbench were pretty essential. We decided to use countersunk 2x4s as uprights. This eliminated the need for pricey cap/acorn nuts while still leaving the all-thread ends 'protected' on the outside and allowing us to put it flush against the wall without causing damage.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
There are some who also swear by their bandsaw for ripping lumber. A bandsaw can cut faster and is far safer to use than a tablesaw. I personally still prefer to use a tablesaw for ripping for two reasons. First, the bandsaw table and fence are smaller than a typical tablesaw. I find this makes it harder for me to keep a straight edge. Second is the quality of cut. A bandsaw rip will usually be rougher than a tablesaw rip.
In recent years, this versatile and accurate tool has become a fixture in the work shop and at the work site. Also called a “chop box,” the miter saw consists of a powerful circular saw mounted on an arm that hinges at the rear of the tool. When the blade is lowered in a chopping motion, it cuts through the workpiece, passing through a slot in the base. The motor and blade can be pivoted with respect to the base for miter cuts. Another adjustment makes it possible to tilt the blade, too, allowing for compound miter cuts, handy for jobs like cutting crown moldings, which are set at a pitched angle and that must also turn around corners. The diameter of the blade determines the maximum cut width, with standard sizes ranging from 8-inch blades up to 15 inches. A 10- or 12-inch saw is sufficient for most jobs.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).

There are several ways to complete this task, including pocket screws, brads or biscuits. I have used all of these methods, but my preference is biscuits, as they provide adequate strength, excellent alignment, and ease. I generally just place one biscuit in the center of each rail and stile, which provides alignment assistance while not being overly constraining when manual adjustments need to be made to achieve desired placement. After applying glue and biscuits, use lots of clamps to create a gap-free bond between the face frame and carcass.
You can make your bookshelf any size you’d like, but a standard size with even proportions is about 12 inches deep, 30 inches wide and 48 inches tall. That's big enough to hold books and magazines, but not so big that it won't fit where you want it to. Note: If your shelves are any longer than 32 inches, you'll need thicker lumber or midspan supports so the shelves won't sag when they're filled with books.
Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
The old saying "If only I knew then what I know now" certainly applies to buying woodworking tools . Like nearly every woodworker, I would love a large shop equipped with all the best tools. Like most woodworkers however, I have had to make choices due to finances, space, and what was available at the time of need. As I look back at the purchases I made over the last 30 years, I have few true regrets, but there are many things I would do differently. Here is how I would approach equipment selection today.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
A jointer makes the dges of your material smooth, straight, and square. This creates what’s commonly called a reference edge that you need for additional steps like ripping or crosscutting. In addition to perfecting the edges of your stock you can also straighten faces, called face jointing. Like edges, you’ll end up with faces that are nice and smooth, and dead flat; a precursor to other machining steps.

Use 1x12 pine lumber for a rustic appearance. Nothing looks like pine with its large knots and swirls. And because you're using solid lumber, you can sand the edges smooth for a finished appearance. Add a 1/4-inch fir plywood back for strength and stability. Note that "1x12" is a nominal size. The actual size will be ¾-inch thick and 11 ¼-inches wide.


An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com. 

We recruited Justin and his son to help us with this story. Justin is a full-time firefighter and a woodworker on his off days. His 11-year-old son Jackson, an up-and-coming woodworker, had fun with his dad and learned a few power tool techniques in the process. We provided the plans and gave a few pointers along the way, and Justin and Jackson took it from there.

Robyn Mierzwa is the founder of Makeville Studio, a community workshop established in 2008 that offers classes in woodworking and furniture making in Brooklyn, NY. A self-taught woodworker, Robyn has honed her craft over many years and continues to learn something new on every project. In addition to furniture making, she is passionate about teaching and is grateful for the opportunity to help others tap into their creative selves through craft.


This is that rare two-for-one deal in which two tools have been effectively made one. The stationary belt sander uses a closed loop of paper that travels at speed around a pair of cylindrical drums. One drum is driven by an electric motor, the other is spring-loaded to maintain belt tension. Powered by the same motor, the stationary disk sander uses sanding disks that spin on a backing plate.
The content of this website, TheArtofHomeRenovations.com, and its associated social media pages, is provided for informational purposes only. The information is not intended as, nor should it be considered a substitute for professional claims, suggestions, diagnosis, or counseling of any kind under any circumstances. By reading this website, you acknowledge that you are responsible for your own decisions. Do not take information from any website, including this one, and try it without proper research and supervision. For more information, please read our Privacy Policy.
The most common bench tools in the woodshop are routers and sanders. We have already talked about routers to some extent. Orbital sanders have come a long way from the jitterbug style of old. New sanders leave a better finish, are quieter and last longer. At some point, probably right away, you will want a sander . No one likes to sand. It is tempting to buy multiple sanders to address an unpleasant task. Here again, I point to the hand tools. Learning to use a smoothing plane and a cabinet scraper will reduce your sanding to little or nothing and cut down your overall time to finish a project.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
There is significant evidence of advanced woodworking in Ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2

Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.

As someone who is just progressing past being a “beginner” (just getting into building furniture) in the woodworking community, I would say there are a number of changes I would make to your list. First, I would say that a power jointer/thicknesser does not belong on the list by any means. They are way too large of an investment and take up a lot of space (not to mention you can buy your stock at the desired dimensions). I also strongly disagree with the concept of joinery devices. As someone new to the trade, I feel this is a very important skill that must be developed, not skipped over by buying devices power devices that achieve a single goal. I think the jigsaw should be replaced by a good bandsaw. I just purchased my first major power tool and it was a 14″ bandsaw and not a tablesaw for space reasons as well as versatility. The bandsaw allows me to resaw, cut curves, (now that it is adjusted for drift) rip pieces of stock accurately that are thicker than a table saw could handle, etc. Once the cut is complete, a handplane can remove any saw marks and square/flatten a surface. It is also really useful for cutting tenons and dovetails. Handsaws can be used for crosscutting and anything else the bandsaw cannot handle. As for a bench, if you are getting into woodworking, this should be your first real project (and it is not expensive to make). You are also missing a good vise to be attached to the bench.
Clamps. Woodworking clamps are essential when building a project. They hold the components together while assembling them together, gluing them, during measuring, cutting et cetera. Be generous with the number of clamps you purchase because you will always need more than you think, and it gets difficult to assemble the project if you do not have enough clamps.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.

Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
Wondering if you are still hanging in there Scott? One thing I notice woodworkers often do when getting started (including myself) is they sell their hand made items way too cheap, it doesn’t help anyone except the customer. You say yourself that they sell as fast as you can make them. Put your prices up! Double or even triple, the amount of orders may slow down but you will be doing yourself a favour. Don’t bother with Etsy or Craigslist or local markets in my opinion. Build it up for yourself to make money not making the giants even richer from all your hard work. I’ve been selling my woodwork online since 2004, before all these giants came along. I feel I have the experience to offer advice if anyone is interested. Trust no one! The internet has become a place for giants to make money off you (Facebook, Etsy, GoogleAds, Amazon…… the list goes on.) Don’t let them take your money, learn how to use them to your advantage instead of being a sucker and paying them money to grow even bigger while you stay the same size. They don’t care about you, they only care about their own business models. Grow your own business brand and ignore anyone who appears to want to help you, especially if their main business is making money online. That’s all they care about! Not you. Invest your time and money in yourself, your own website – not others and you will succeed, providing you are doing what you love and are passionate about.
×