It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.

In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud. 

There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
When many people hear the word woodworker, the image of someone leaning over a workbench sanding a long piece of wood with his or her hands. However, modern woodworking requires training on highly technical machinery, such as CNC (computerized numerical control) machines.  Even woodworkers caught somewhere between modern equipment and a hand planer typically use CNC machines to fabricate large or intricate products.  If working for a large company, a lot of the work will be done on an assembly line or in various areas on the floor designated to complete a particular part of a project.   The tasks will be handled by different workers with very specialized training on each machine. For example, one machine might cut a large piece of wood into three sections, whereas another machine might take one of the sections and round each edge.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
Stiles are 2-1/2″ x 72″, the top rail measures 1-1/2″ x 32-3/4″, and the bottom rail is 2-1/2″ x 32-3/4″”. My favorite way to assemble frames is with a pocket hole jig, but you can also choose to use biscuits, or simply use brads to nail individual face frame pieces into place. I sometimes use that approach for large built-ins, where it may be cumbersome to construct a face frame on-site during the installation process. The school that will receive these bookcases requested that the face frame go all the way to the floor to prevent pencils and other items from rolling underneath. I generally prefer to keep the face frame about 2″ from the floor to lighten the appearance, but this is a stylistic choice. On larger pieces, such as armoires, I like to keep them high enough to allow a vacuum cleaner to pass underneath.
To reduce the risk of personal injury and property damage, read and follow all related product manufacturers instruction manuals and information before performing any of the applications shown. Some construction-related applications shown may not be allowed in your local area. Consult your local authority having jurisdiction (AHJ) before starting work for information on permits, applicable codes, and other regulations. Black & Decker disclaims any responsibility for any damage to property or injury to persons as a result of misuse of the information provided.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Wondering if you are still hanging in there Scott? One thing I notice woodworkers often do when getting started (including myself) is they sell their hand made items way too cheap, it doesn’t help anyone except the customer. You say yourself that they sell as fast as you can make them. Put your prices up! Double or even triple, the amount of orders may slow down but you will be doing yourself a favour. Don’t bother with Etsy or Craigslist or local markets in my opinion. Build it up for yourself to make money not making the giants even richer from all your hard work. I’ve been selling my woodwork online since 2004, before all these giants came along. I feel I have the experience to offer advice if anyone is interested. Trust no one! The internet has become a place for giants to make money off you (Facebook, Etsy, GoogleAds, Amazon…… the list goes on.) Don’t let them take your money, learn how to use them to your advantage instead of being a sucker and paying them money to grow even bigger while you stay the same size. They don’t care about you, they only care about their own business models. Grow your own business brand and ignore anyone who appears to want to help you, especially if their main business is making money online. That’s all they care about! Not you. Invest your time and money in yourself, your own website – not others and you will succeed, providing you are doing what you love and are passionate about.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
Lots of ways. Woodworking really reinforces my independent nature. Blogs are good. Norm Abrams videos. I have a library of magazines and books with really neat projects which I love to read over and over to get a sense of how other woodworkers think through their creative projects. I have a painter friend with whom I endlessly brainstorm how to finish the final wood project. But really, the wood itself teaches me the most. Each species has different needs. The projects also teach me. Each project is unique in approach, design, and method. I’ve learned to listen and make myself a servant of these things. I come to the shop ready to learn.
Nearly every woodworking project in one form or another will require you to check some intersection, joint, or board end for squareness, or "square." In some cases, you'll need to confirm that an entire assembly is square. For small projects, you can use a squaring tool, such as a try square, speed square, or framing square. For larger projects, you can check for square by measuring diagonally between opposing corners: The assembly is square when the measurements are equal. You can also use the 3-4-5 method, based on the Pythagorean Theorem: a2 + b2 = c2.
My hands-down favorite thing to do is develop the process for manufacturing a new product. This involves figuring out how to design a product so that it’s not only durable and functional, but also economical to build. Then all the jigs, fixtures and CNC programs have to be created and tested until the whole process is running smoothly. Up to now, the most challenging project has been our line of wooden sunglasses which were developed for a specific client. We spent hundreds of hours just figuring out how to build the first pair then hundreds more hours refining the process until they became profitable.
Whether they’re just getting started, or have been involved with woodworking for a while, many woodworkers wonder what woodworking power tools they should add to their shop. The answer to this question can be subjective, and depend on what types of woodworking projects you commonly build, but George Vondriska is ready to provide you with his opinion on which five woodworking power tools should be considered top tier tools for your shop.
The table saw is the center of most workshops; it is the largest and most imposing tool in the shop. While it is an important tool, one could claim that table saw need not be on this list. However, it is an important tool and shows that creating a shop is not a matter of just collecting hand tools. There are jobs that hand tools cannot do as well as tools like the table saw, especially when there is such a wide variety of blades which can be set up and changed for so many different applications. Table saws create straight and consistent cuts. When setting up a table saw for a cut, one needs to set the depth of the blade and adjust the fence according to the width desired.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down. 

Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
These types of guitar picks are quite easy to make and are perfect for that special musician or guitar player in someone’s family.While they’re not quite good at being used for playing guitar (wood and metal plus constant friction are bad for both parties), the make a lovely ornament for any player and are a great gift, for Christmas or birthdays, to give to that serenading someone.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
As part of the job, woodworkers prepare and operate saws, drill presses, routers, sanders, lathes, shapers, milling machines, and planers.  Often using a template, woodworkers measure and verify dimensions, cut, and shape wooden parts. Woodworkers stain or coat the wood products with sealers and topcoats, such as varnish and lacquer. But, they also often install hardware, fit electrical components and specialty products, such as metal trims and glass.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.
Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
But before you purchase clamps, build your first project and put it together without glue. Then see how many clamps you think you will need to put enough pressure in all the right spots. Then proceed to purchase that number of clamps. Repeat this process on your next project, and purchase more clamps if needed. See my buying guide for different clamp types, uses, and my favorite brands.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
If you enjoy these free bookcase plans be sure to check out these other free woodworking plans for shelves, coffee tables, entertainment centers, desks, Little Free Library, wine racks, jewelry boxes, home bars, kitchen islands, bathroom vanities, playhouses, picnic tables, dog houses, decks, workbenches, tree houses, pergolas, sheds, Adirondack chairs, bunk beds, and even chicken coops.

The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.


I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
Add a little rustic décor to your walls by building a wooden mail sorter. Not only does this give you beautiful rustic décor, it also serves a very handy function by keeping mail neatly organized. You just need a few pieces of wood and some small coat hooks at the bottom to hang your keys. Stain it in any color you want and you have a very functional and very beautiful sorter.
Don’t be afraid to ask if there are internship or apprenticeship opportunities. Even if you’re declined, people will know you’re looking, and if you continue to hang out in their circles and demonstrate that you’d be a model employee, someone will take notice. There’s no shortage of woodworkers, but there is a severe shortage of enthusiastic and phenomenal woodworkers.
And, although a formal education is helpful, it is not necessary, and most woodworkers receive on-the-job training under the supervision of other more experienced workers.  However, because of the ongoing development and modernizing of woodworking machinery, many employers are requiring applicants to have at least a high school diploma, or a few years training in math (specifically geometry) and computer applications.  Many woodworkers will receive training by enrolling in a community or technical college.  Some may attend a university that offers coursework in furniture manufacturing or wood engineering. Individuals who have earned a degree can often move into management or supervisory positions, or go on to open their own woodworking shop.  Becoming a skilled woodworker can often take years, and knowledge of blueprints and work sequences takes training and practice.

Break down plywood Following the cutting diagram, crosscut plywood along the line marked “first cut”. Take the smaller of the two rip 3/4″ plywood according to diagram and cut list. For safety and easier handling, use a circular saw with a good quality blade (following a straight edge guide for a straight cut) for first cross-cut on plywood. If you are not confident in your circular saw’s ability to cut straight lines with no tear out, leave yourself 1/4″ of extra material (there is enough extra material in a 4′ x 8′ sheet of plywood to do this) and make your final cuts on the table saw.
Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results.
Manufacturing the furniture is one of the most complex crafts, because manufacturing the good quality furniture requires a lot of skills, tools and rich experience. As the part of interior, the furniture is always on the visible place and it is often the main element of interior decorations. Because of this, its manufacture does not allow any mistakes. Just a tiny error on a visible place can often ruin all the effort that was made to produce that piece of the furniture. Because of that, a quality furniture plan is one of the basic things for reducing the risk of errors.
×