We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Description: You've seen him demo in the store, now come join Rod Hendrickson to learn to carve your own realistic animals. Beginners and carvers of all levels are welcome to join this on-going class. First time students will make a miniature duck decoy. Tuition is for 12 hours of class time. Rough cut outs are supplied by the instructor - check with Rod for cost. (approximately $15 for the miniature duck decoy blank)
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
You should also double-check the length of your all-thread rods. I'd dummy one up and try it out before cutting all of them. It needs to be just long enough to catch a couple of threads and snug down without punching out through the cap nut. The actual "cap" portion of cap nuts is fairly thin, and if the all-thread is even a bit too long it will punch through the end when you snug it up.
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.

This demise of shop classes is quite unfortunate, as they were never solely about preparing students for trade employment. Rather, they taught all men manual skills that they could use and enjoy throughout their lives, whether they became a carpenter or a doctor. They were considered part of becoming a well-rounded man – one able to use both his hands and his mind.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
9.  Hand tools and machines: In our furniture plans, you will find only dimensions of the furniture and directions for their construction; we do not suggest manufacture techniques. We recommend that you decide for yourself how you will make particular parts of the furniture – based on your experience, skills in specific techniques and operations and depending on the machines and tools that you got.
I also had the brainstorm to use two nail-in furniture "feet" on the bottom of each 2x4 on the front side so as to compensate for the carpet tack strip on the back edge and to make the shelves lean ever so slightly into the wall. I thought we might have to anchor the top of it to the wall, but with the feet, it stands very firm with absolutely no signs of wanting to tip forward! I felt great satisfaction when the almost 150 square inches of friction applied allowed for NO racking -- I could practically climb the end without anything budging!
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
To add some additional dimension to the bookcase, you can use corner posts to dress up the bookcase. I like to use a contrasting wood to highlight this element (such as maple posts with walnut carcass as shown), but this is a stylistic preference. The posts can be square, or tapered. I prefer to cut these as tapers, using a band saw to make the angled cuts on the two outside surfaces of each corner post.
A wall-bed combination or drop-down bed helps save a lot of room in a tight basement, so consider installing this Murphy bed and bookcase. It’s one of many great basement bedroom ideas. Further, a Murphy bed can be super simple: Some are just an upright box that contains a folddown bed. But this is a deluxe version because it includes ample storage.

For large outdoor gatherings, copious seating is a necessity. This outdoor couch can fit several adults, and oversized arm rests act as end tables for drinks. Before getting started, you’ll want to pick up the cushions for the couch first; depending on their size, you can make any adjustments to the cut list necessary for the perfect fit. Once you have the cushions, all the materials you need can be found at local home centers. We used treated lumber, but you can splurge for a naturally rot-resistant wood like cedar or cypress. We’ve got the full plans here.

As Chief Creative Officer and Founding Partner at Brit + Co, Anjelika Temple brings her voracious consumption of all things creative and colorful to DIY projects, geeky gadgetry finds and more. When she's not DIY-ing her heart out, you'll find her throwing dinner parties with friends or adventuring with her husband David, their daughter Anokhi, and their silly dog Turkey.
Each bookcase door has a fixed middle shelf and four adjustable shelves. The doors are available in hardwood veneers, MDF or vinyl-lam. Bookcase sizes range from 36in. to 66in.wide and up to 96in. high. Order them directly from the manufacturer. The system, weighing 400 lbs., will show up on a single pallet. Prices start at $2,200 (plus shipping) for the entire system.
I was self taught meaning I gleaned anything and everything I could from books,DVD’s,TV shows like Norm,Roy Underhill and any where else I could pick up information.Even though I had more than 20 years of woodworking I have in the last few years I’ve found a mentor in Charles Neil and now subscribe to his on line Mastering woodworking show. As to taking a class I’m a bit prejudice since I teach a community collage class on woodworking I highly recommend that you take any classes you can afford.
Description: In this four day class, we will start with rough lumber and finish with a simple box. Along the way we will teach you how to use the jointer, planer, table saw, and router table This is THE class to take if you are interested in getting started the right way in woodworking. This one will fill up fast, so sign up. soon. Woodworking 101 is strongly recommended for beginners and people looking to review the basics.
It's a little strange but you can charge premium prices for birdhouses and people are ready to pay for it. People who want to enjoy birds coming to the garden, attach a high value to a functional and nice looking bird-house. And who doesn't really want pretty birds coming and chirping in their gardens. Therefore, birdhouse is one of the top-selling woodworking projects.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
My whole life, I’ve loved to be creative and make things. Once I got older though, creativity and anything art related really got pushed aside for a more serious career path. After graduating from college, I decided to go to grad school, get my MS in accounting, and then I became a CPA (Certified Public Accountant), and started working in accounting for several years.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
To give you an idea about the different bookshelf plans available,this guide presents you 17 simple but alluring bookcase designs to choose from. The designs are not only in a wide array of sizes and styles but they are also inexpensive to build and will fulfil your home space. So be sure to go through all of them to find the best one for your room.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.

Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.

Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.

Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.
Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
If you would like to follow up on these things to learn how to work wood yourself, you could comb through a Google search for each of the topics listed but, to simplify your education, I recommend picking up a few helpful books to start. The first two are mostly about techniques, and the last one is about how to choose which hand tools to purchase.
Bruce Lamo has done woodworking pretty much all his life, although never exclusively to make a living. He prefers making furniture and working with solid wood, but often uses plywood when making cabinets. This article originated when a few friends were considering buying tools that based on his experience, he thought would not be a good investment.

The Nine-month Comprehensive is designed for aspiring professional furniture makers and dedicated amateurs who seek in-depth training at the highest standard of excellence. The hands-on, project-oriented format includes the full range of furniture making skills. Sequential projects take students from the fundamentals through the fine points of design and craftsmanship.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.

At some point dust collection needs to be considered. For safety reasons all power tools should run in conjunction with a good dust collection system. However the reality is that many woodworkers will put up with the dust for a while, if not forever. There are machines that really can't be run without dust collection such as a large planer or a bandsaw. The chips and sawdust must be extracted or else the buildup will damage the machine. A large shop vac may be sufficient for smaller machines, and portable dust collectors are available that can be moved from one machine to another. Dust collection is a reasonable investment that should actually be made early on. Your health is well worth the cost.
Glue up a panel using the same material as your face frame. I generally size the top so that it overhangs by about 1″ on all sides, which means a 38-1/2″ x 13-1/4″ panel. Trim to size using a panel cutting jig. An alternative approach to building the top is to use a piece of 3/4″ plywood (same material you used for the sides and shelves), with wood strips applied to each edge as edge banding to mask the laminations, using the same approach as you used to edge band the shelves.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.

×