A small jointer is better than no jointer, but a small jointer is not a great addition to a shop. A jointer needs table length. I would skip buying a small to medium size jointer. Once again, rely on your hand tools. They can perform as well or better than a machine that costs hundreds more, they require a great deal of room, and they should be run in conjunction with a dust collector. You can flatten boards with a jack plane and straighten edges with a jointer. With a little experience it becomes a quick task.
Nearly every woodworking project in one form or another will require you to check some intersection, joint, or board end for squareness, or "square." In some cases, you'll need to confirm that an entire assembly is square. For small projects, you can use a squaring tool, such as a try square, speed square, or framing square. For larger projects, you can check for square by measuring diagonally between opposing corners: The assembly is square when the measurements are equal. You can also use the 3-4-5 method, based on the Pythagorean Theorem: a2 + b2 = c2.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Once you’ve mastered the basics, then check out magazines like Fine Woodworking, Woodcraft, etc. Visit your local woodworking store (like Woodcraft or Rockler) and browse the book / plans section. What I like is these stores normally have people with woodworking expertise and can answer most of your questions whether they be basic or advanced. They also offer monthly workshops at an affordable price.
Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)

To add some additional dimension to the bookcase, you can use corner posts to dress up the bookcase. I like to use a contrasting wood to highlight this element (such as maple posts with walnut carcass as shown), but this is a stylistic preference. The posts can be square, or tapered. I prefer to cut these as tapers, using a band saw to make the angled cuts on the two outside surfaces of each corner post.


Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall

There is significant evidence of advanced woodworking in Ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2
Steely blue walls and a few intricately placed wood slices will give your bathroom a great rustic look. You will need several wood slices to go all the way around the room and then just place them in geometric patterns or however you want. Thin wood slices will affix to the walls easily with wallpaper glue or you can use a hot glue gun if you prefer.
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.
This is the most fundamental joint in all wood construction. Whenever we have to join a horizontal member (like a chair rail) to a vertical member (like a leg), we need to interlock these pieces at a right angle. By fitting a tenon into a corresponding mortise (hole), we can create a solid 90° joint. Although it may look intuitive to make, achieving a nice, tight fit requires careful technique and practice. There are many ways to make a mortise, but I use a stout chisel designed for that task and simply determine the width of the tenon based on that chisel’s dimension. Cutting the tenon is usually a matter of four straight saw cuts. When you do learn how to lay this joint out properly and cut it to a snug fit, the world of woodworking opens up to you. At that point, you know all the joinery required to build most tables and chairs.
Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.

My parents have the space and Dad has the tools -- a drill press, forstner bits and a long workbench were pretty essential. We decided to use countersunk 2x4s as uprights. This eliminated the need for pricey cap/acorn nuts while still leaving the all-thread ends 'protected' on the outside and allowing us to put it flush against the wall without causing damage.


Thank you for sharing your story! Would love to hear how you got started with your blog and business too someday, I always find it so interesting what inspires people to shift their career path. I can’t believe you’ve learned so much with YouTube videos! And congrats on creating such a successful business from scratch and also having the courage to walk away when you knew it wasn’t for you anymore. We’re having a home built next year, so look forward to checking out all the custom work you’ve done with your place!


Picture frames is a very versatile woodworking project. You can make it as simple as you like. A little bit of ingenuity allows you to create several original designs. This is one woodworking project that can never go stale, because you will never run out of ideas to make new designs and also because it is an evergreen item that will always be in demand.
With a lot of woodworking tools, the basic technique is pretty self-explanatory. But not all of them are so intuitive. Proper use of hand planes requires a bit of instruction and practice to develop the feel of adjusting the cut from coarse to fine. Additionally, the edge can be askew or the cap iron can be in the wrong place. Although these things require a little bit of research to figure out, properly using a hand plane is an undeniably attainable skill. I encourage you to grab an old plane and hop on YouTube to search “tune up an old hand plane” or “how to use a hand plane.” There will be more than enough hours of video to make up for what you missed in shop class.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)

Then, beginning several decades ago, shop classes began to be removed from secondary curriculums. With the decrease in educational funding, and increasing emphasis on standardized testing, schools began to cull electives, institute stricter graduation requirements, and focus more on college prep academics and the subjects necessary for passing state exams. There wasn’t money or time to maintain tools and sawdust-filled workshops, and one by one school districts dropped their shop classes, figuring that students who wished to pursue trade skills could do so later at a vocational college.


Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Add curves and other fancy touches to your bookcase the easy way with polyurethane plastic trim. Working with polyurethane trim is much like working with wood—you cut it with standard saw blades, nail it by hand or with a gun and paint it just like wood. Home centers carry a small selection of polyurethane trim. You can find an endless variety of options by going online and searching for “polyurethane trim” (some products are listed as “urethane” rather than “polyurethane”).
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
Description: You've seen him demo in the store, now come join Rod Hendrickson to learn to carve your own realistic animals. Beginners and carvers of all levels are welcome to join this on-going class. First time students will make a miniature duck decoy. Tuition is for 12 hours of class time. Rough cut outs are supplied by the instructor - check with Rod for cost. (approximately $15 for the miniature duck decoy blank)
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.

Tightening the nuts clamps the uprights against the shelves, holding them in place and providing shear strength (through friction) for the whole assembly. I know of an 8' tall, 12' long version of these shelves that has survived a few minor earthquakes while fully loaded with hundreds of books. Once the nuts are tightened on my smaller versions, I (all 240lbs of me) have a very hard time "racking" the shelves by pushing on one end of them in an attempt to get them to collapse: I can't.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
There may or may not be an easy answer to this. If you already have a woodworking craft you are passionate about, then that's great. All you need to do is a little market research to figure out whether others love it as much as you do. You do not have to go very far and wide to do some primary market research. Start with your family and friends who will give you a fair and honest opinion.
The jigsaw, another hand held and versatile saw, is used for cutting curves. One has a lot of freedom with a jig saw because it can cut curves, circles and straight. Depending on the width of the blade, the curves can be very fine. The down side to the jigsaw is that straight lines can be difficult depending on the wood you are cutting. No matter, it is important to make sure to always have sharp blades.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
It could be a pun about family life, or a comment on whatever pets have currently made their territory. People love these simple decorations right next to their front doors.With just a board, a little creative painting, and some simple small hooks, you can find yourself around $15 per holder, all for around 30 minutes of sanding, cutting, and painting. 
Teds woodworking іѕ trying to prevent ԁο-it-yourselfers from continuing to learn it the hard way bесаυѕе anyone who іѕ not a professional carpenter аnԁ hаѕ tried tο complete a woodworking project hаѕ learned that mistakes саn bе expensive. Thе package includes over 16,000 projects, which аrе аƖƖ conveniently delivered іn a digital format. When selecting a project frοm the database, one саn bеɡіn bу first reviewing the detailed material list аnԁ tool guide fοr that specific project. Ted takes the guesswork out οf having tο estimate wood required tο complete a project bесаυѕе even аѕ a professional carpenter fοr 36 years hе felt frustrated bу the guess work required wіth οthеr blue prints. Mοѕt blue prints οn the market today аrе difficult tο read аnԁ harder tο follow. Sadly, many woodworking reference books contain project plans that wіƖƖ result іn frustrating аnԁ incomplete woodworking projects. Teds Woodworking works bесаυѕе іt simplifies the process аnԁ gives information suitable tο аƖƖ levels οf carpentry experience.
The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.

Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.
I use chisels perhaps more than any other tool in my workshop, so it’s a good idea to not cheap out here. A high quality set of bevel edge bench chisels (new or vintage) will last you many years (likely  your entire life) and will be used on nearly every project. I’ve used some descent affordable plastic handle bench chisels, but highly prefer lighter wooden handle chisels with excellent steel.
This is that rare two-for-one deal in which two tools have been effectively made one. The stationary belt sander uses a closed loop of paper that travels at speed around a pair of cylindrical drums. One drum is driven by an electric motor, the other is spring-loaded to maintain belt tension. Powered by the same motor, the stationary disk sander uses sanding disks that spin on a backing plate.

I’ve got a three other bits of advice: First of all, get really, really good at woodworking. There are lots of people who enjoy it as a hobby. To sell your services, you’ve got to be able to do far superior work or do it much faster than everyone else (preferably both). Failure to do so means competing against hundreds of amateurs who make things for the pleasure of it, then sell their work at cost to fund the hobby. Second, develop great people skills. Most professionals do custom work and few focus on selling a product. Most of them sell a service, and a big part of that is getting customers to enjoy the experience of collaborating with a woodworker to create their dream products. If your customers don’t like you, they can usually save time and money by getting something from an online catalog. People who buy handcrafted items from woodworkers are often attracted to the idea of supporting artisans. The face behind the work is important to them. Last, develop an iron-clad work ethic. In this field you’re directly trading time for money, and that time is very limited. It’s important to be productive, so try to get 40 hours of actual productivity (as in making things) every week. Accounting, phone conversations and social media marketing may be important, but none of them provide an actual paycheck, so they don’t count as productive work.
If you`ve found the diy bookshelf plans  below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
Lots of ways. Woodworking really reinforces my independent nature. Blogs are good. Norm Abrams videos. I have a library of magazines and books with really neat projects which I love to read over and over to get a sense of how other woodworkers think through their creative projects. I have a painter friend with whom I endlessly brainstorm how to finish the final wood project. But really, the wood itself teaches me the most. Each species has different needs. The projects also teach me. Each project is unique in approach, design, and method. I’ve learned to listen and make myself a servant of these things. I come to the shop ready to learn.
Manufacturing the furniture is one of the most complex crafts, because manufacturing the good quality furniture requires a lot of skills, tools and rich experience. As the part of interior, the furniture is always on the visible place and it is often the main element of interior decorations. Because of this, its manufacture does not allow any mistakes. Just a tiny error on a visible place can often ruin all the effort that was made to produce that piece of the furniture. Because of that, a quality furniture plan is one of the basic things for reducing the risk of errors.
×