At some point dust collection needs to be considered. For safety reasons all power tools should run in conjunction with a good dust collection system. However the reality is that many woodworkers will put up with the dust for a while, if not forever. There are machines that really can't be run without dust collection such as a large planer or a bandsaw. The chips and sawdust must be extracted or else the buildup will damage the machine. A large shop vac may be sufficient for smaller machines, and portable dust collectors are available that can be moved from one machine to another. Dust collection is a reasonable investment that should actually be made early on. Your health is well worth the cost.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project. 

Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.

Add curves and other fancy touches to your bookcase the easy way with polyurethane plastic trim. Working with polyurethane trim is much like working with wood—you cut it with standard saw blades, nail it by hand or with a gun and paint it just like wood. Home centers carry a small selection of polyurethane trim. You can find an endless variety of options by going online and searching for “polyurethane trim” (some products are listed as “urethane” rather than “polyurethane”).
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )

Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
Stiles are 2-1/2″ x 72″, the top rail measures 1-1/2″ x 32-3/4″, and the bottom rail is 2-1/2″ x 32-3/4″”. My favorite way to assemble frames is with a pocket hole jig, but you can also choose to use biscuits, or simply use brads to nail individual face frame pieces into place. I sometimes use that approach for large built-ins, where it may be cumbersome to construct a face frame on-site during the installation process. The school that will receive these bookcases requested that the face frame go all the way to the floor to prevent pencils and other items from rolling underneath. I generally prefer to keep the face frame about 2″ from the floor to lighten the appearance, but this is a stylistic choice. On larger pieces, such as armoires, I like to keep them high enough to allow a vacuum cleaner to pass underneath.
Then, beginning several decades ago, shop classes began to be removed from secondary curriculums. With the decrease in educational funding, and increasing emphasis on standardized testing, schools began to cull electives, institute stricter graduation requirements, and focus more on college prep academics and the subjects necessary for passing state exams. There wasn’t money or time to maintain tools and sawdust-filled workshops, and one by one school districts dropped their shop classes, figuring that students who wished to pursue trade skills could do so later at a vocational college.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
I know this is an old forum topic, but I felt the need to chime in. I was in Jr. High back in the late 70s and my school had a wood shop and I still have a cutting board and a three leg single post foyer table made from those shops and very proud of them. It is sad seeing the lack of “hands on” classes these days in schools because of liability issues. Just recently got back into woodworking last year and honestly Marc has much to do with that and his YouTube videos, that and a date night where my wife and I went to a Woodcraft class for making pens. I plan on joining the guild at some point but wanted to get enough tools and skills together to make the guild worth it for me and I am almost there. I am currently working on the 2015 Kids Table from Woodworkers Fighting Cancer and will donate to them as well when I finish even though it is way past due it is the perfect project for my daughter. Since I started I have made pens, cutting boards, a toy airplane and now working on this table and love it. Thank you Marc for being such an influence on this community!!

In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
If you`ve found the diy bookshelf plans  below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Lots of ways. Woodworking really reinforces my independent nature. Blogs are good. Norm Abrams videos. I have a library of magazines and books with really neat projects which I love to read over and over to get a sense of how other woodworkers think through their creative projects. I have a painter friend with whom I endlessly brainstorm how to finish the final wood project. But really, the wood itself teaches me the most. Each species has different needs. The projects also teach me. Each project is unique in approach, design, and method. I’ve learned to listen and make myself a servant of these things. I come to the shop ready to learn.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
The router is a hand held tool which is often mounted upside down and is used to hollow out an area in the face of a work piece. It is also used to cut profiles for moldings and adding decorative edges to any piece enhances its beauty and dimension. Routers are also used to cut joinery, such as dovetails and dados. The beauty of a router is that one can purchase an unlimited number of profiles to best suit the many requirements which arise with woodworking.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
I decided to start my own vintage rental company, with farm tables being the main rental item. There was just one problem, I couldn’t afford to buy twenty farm tables… Which led me to my only option, I’d have to build them, except that again I didn’t know a thing about building or power tools nor did I know anyone that I felt comfortable asking to teach me. But, I figured if I could pass the CPA exam, I could figure out how to build a table on my own and learn how to use power tools.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
I agree with your list. My table (cabinet) saw has a router mount built into the table to the right of the blade and it works great. The table is flat cast iron and I can use the table saw fence. I’ve also built an auxiliary fence with dust collection and more features. The only downside is I can’t use a router lift and have to make depth adjustments under the table. To avoid frequent band saw blade changes, I have two: a big one (17″, 2HP, 12″ thick capacity) for typical work and a 9″ bench-top unit that I keep a narrow blade in. I also build radio control airplanes and the small one works great on small stock.
It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period. Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
Offer good for one item at regular price only. Limit one coupon per customer per day. Must present coupon at time of purchase. Offer is not valid with any other coupon, discount or previous purchase. One cut or one bolt of fabric or trim "by the yard" equals one item. Online fabric & trim discount is limited to 10 yards, single cut. Excludes CRICUT® products, candy & snack products, gum & mints, gift cards, custom orders, labor, rentals, class fees or items labeled "Your Price". Exclusions subject to change. Cash Value 1/10¢. 
×