Keeping your house clean and well-sorted is probably one of the trickiest tasks, especially if you are one of those people who have more books than clothes and shoes combined. Each of your books is priceless and you want to preserve them in the best condition possible. But it is not always so easy, especially if you do not have a proper bookshelf. Now bookshelves do not come cheap, be it a simple plywood one or an ornate wooden case. So, here are forty simple yet trendy DIY bookshelves for you and your books.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
Work bench. You might get by by using a saw horse as your work bench for a while but believe us when we tell you that you need a dedicated sturdy work bench for doing your woodwork. You can buy one, or like many woodworker, make one yourself. You can make your own workbench for under $200. There are plenty of free videos and guides online that will show you how. Just type your search in a search engine.
Whether starting a workshop from scratch or enhancing an existing one, few woodworkers will come up with the same workshop tools wish lists. Most often the first priority is either a table saw, band saw, or radial arm saw, followed by equipment to dress up lumber, such as a planer, lathe, and drill press. From there on, the equipment you’ll want will depend to a large degree on the projects you end up building most often.
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.) So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
As for schooling, many local school districts, community colleges and woodworking stores offer woodworking classes, but those are a mixed bag. A handful is really good and many are terrible. There’s also a big difference between woodworking for fun and doing it for a living, and most classes are geared towards hobbyists. Out of all the proper woodworking schools with good reputations, I’ve only had personal experience with Marc Adams School of Woodworking. That place I recommend 100%, as the instructors are generally active professionals in their specialized niches, so one can always pick their brains for extra information related to earning a living. The director of the school also does a good job of screening instructors to eliminate the ones that don’t interact well in a classroom setting.