I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
Next, grab a role of tape to make your rounded corners for the arms and back supports. Do a rounded corner for the two outside armrests, and for both outside pieces of the table top. Create rounded corners for the top of the backrest supports as well(Part H). Cut with a jigsaw and use an orbital sander to smooth the edges. Check out photos in later parts of the project to see the rounded edges.
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period. Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
Picture it: eight people with different skill levels, each trying to design a different project (which, by the way, they have no idea how to do) and hopefully cutting some wood by the third class. Meanwhile, the instructor is running from student to student, and then running to the table saw where a kickback has occurred. It is no wonder that at the end of the class not a single thing has been made and most of the students don't come back.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
A Jack Handplane is a middle size “bench plane” (i.e. planes that are used so often that they are usually on your workbench). If you’re on a budget a jack plane can temporarily be used in place of other planes that perform specialized functions: (1) rough stock removal (if you buy a second iron/blade and shape it with a curved “camber”), (2) jointing board edges (as long as they aren’t too long), and (3) smoothing the boards.
To add some additional dimension to the bookcase, you can use corner posts to dress up the bookcase. I like to use a contrasting wood to highlight this element (such as maple posts with walnut carcass as shown), but this is a stylistic preference. The posts can be square, or tapered. I prefer to cut these as tapers, using a band saw to make the angled cuts on the two outside surfaces of each corner post.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Just create stunning “professional woodworking projects” with the step-by-step instructions given in a blueprint to participate in 16,000 completed woodworking projects. Just read the simple steps that you should follow before doing it practically, and you will feel confident all the time. With the simple “hand holding” instructions, you can complete the wood project in very little time.
Multiples of these bookcases can be connected to form a single, larger unit, generally for a built-in application. To do so, simply build them without a face frame, and finish boards that can be used to construct the face frame separately. Then, nail the face frame in place using brads after the cases are installed. To improve the appearance of the face frame joints using this approach, mill the rails (horizontal pieces) so that they are 1/8-in thinner than the stiles (vertical pieces). This creates a nice shadow line and conceals any unevenness at the joint. Also build a single long top to tie all the pieces together. I use plywood with biscuits to span beyond 8″, edge banded with hardwood strips as you have done for your shelves.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.

One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.


Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.
If you`ve found the diy bookshelf plans  below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
The Nine-month Comprehensive is designed for aspiring professional furniture makers and dedicated amateurs who seek in-depth training at the highest standard of excellence. The hands-on, project-oriented format includes the full range of furniture making skills. Sequential projects take students from the fundamentals through the fine points of design and craftsmanship.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
I generally use biscuits for this (three per joint), and I have never had a joint fail (and a bookcase spending five years in an elementary school is a pretty fair test), but dadoes work great here as well. To assist with accuracy and consistency when using biscuits, mark your biscuit locations on a piece of scrap, and then use the scrap as a guide as you mill biscuit slots in each carcass member. The carcass top is attached so that it is flush with the top of the carcass sides. The carcass bottom is attached so that the top of the panel is 2-1/2″ above the floor (or the bottom of the side panel). 

Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.

You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.

Steely blue walls and a few intricately placed wood slices will give your bathroom a great rustic look. You will need several wood slices to go all the way around the room and then just place them in geometric patterns or however you want. Thin wood slices will affix to the walls easily with wallpaper glue or you can use a hot glue gun if you prefer.
Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.

I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
Plywood shelves are simple to cut, but look a little thin and can sag over time under the weight of books and other payload. I like to apply a solid hardwood strip of at least 1″ thick to strengthen the shelf and give it a more robust appearance. Cut four strips to 3/4″ x 1″ x 36-1/4″ (slightly longer than the shelf itself, allowing you to trim flush later). I attach this strip by simply gluing and carefully clamping for good alignment, gluing the 1″ thickness to the plywood. In the past I have also used biscuits or brads for attaching the strips, but I have found it to be unnecessary, and the method I currently use delivers great results every time. Use a lot of clamps to ensure a good bond between the plywood and edge strip. Carefully force each surface flush as you move from clamp to clamp. If you are careful here, you can save yourself a lot of sanding effort later.
It's a little strange but you can charge premium prices for birdhouses and people are ready to pay for it. People who want to enjoy birds coming to the garden, attach a high value to a functional and nice looking bird-house. And who doesn't really want pretty birds coming and chirping in their gardens. Therefore, birdhouse is one of the top-selling woodworking projects.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Make It: Paint one spring-style clothespin, two craft sticks, and one mini craft stick in your child's favorite colors. Once dry, glue a craft stick on top and bottom of the clothespin as wings, and the mini craft stick as the tail. Cut a triangle from crafts foam and glue it upright atop the mini craft stick. Once dry, glue strong magnets on the bottom of the clothespin.
Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.Woodworking shop in Germany in 1568, the worker in front is using a bow saw, the one in the background is planing.Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
Power drills are something most people have in their homes, and something every father in law should buy for their kids’ wedding. Therefore, this is probably not something one would need to go out and buy. As you can see, there is no drill press on this list; perhaps it would be number 11, 12, or 13. The point is that starters should buy what they can get away with to achieve similar results. With that being said, there are ways to convert your hand held drill into a drill press, if necessary. Additionally, the versatility comes with options of other accessories.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
When many people hear the word woodworker, the image of someone leaning over a workbench sanding a long piece of wood with his or her hands. However, modern woodworking requires training on highly technical machinery, such as CNC (computerized numerical control) machines.  Even woodworkers caught somewhere between modern equipment and a hand planer typically use CNC machines to fabricate large or intricate products.  If working for a large company, a lot of the work will be done on an assembly line or in various areas on the floor designated to complete a particular part of a project.   The tasks will be handled by different workers with very specialized training on each machine. For example, one machine might cut a large piece of wood into three sections, whereas another machine might take one of the sections and round each edge.
Power Tools — A good table saw is usually the most used machine in the shop. New saws have vastly improved fences and better safety features. A good contractor saw has adequate power and can come with up to 49" of ripping capacity to handle sheet goods. This would be my first big purchase. A router is often a highly coveted machine. There are almost endless cutters available now and it is hard to argue with their versatility. I recommend looking at the combo packages that include a plunge base. It is a good way to get two machines for the price of one. In my opinion, an elaborate router table is not necessary for most applications, nor are the expensive and bulky jigs and templates for making joints. What tends to happen is the tools start to drive what is made. Drawers start to fit the machine or template instead of the piece of furniture. Sufficient joints can be made with the table saw, by hand, or you can make your own templates to fit your project.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Woodturning is the craft of using the wood lathe with hand-held tools to cut a shape that is symmetrical around the axis of rotation. Like the potter's wheel, the wood lathe is a simple mechanism which can generate a variety of forms. The operator is known as a turner, and the skills needed to use the tools were traditionally known as turnery. In pre-industrial England, these skills were sufficiently difficult to be known as 'the misterie' of the turners guild. The skills to use the tools by hand, without a fixed point of contact with the wood, distinguish woodturning and the wood lathe from the machinists lathe, or metal-working lathe. 

Upon graduating from high school, I wasn’t sure exactly what career to pursue, but I knew it had to be something that involved creating things with my hands. I’d always had natural talent working with tools, and despite having been an A-average student, I was never fond of conventional academics. Not having better plans at the time, I took one calculus course, got an “A”, then promptly decided two things: I didn’t enjoy college and taking on any debt would force me into a dull, conventional 9-5 job until the debt could be paid off. I didn’t know this back then, but I was pretty much a textbook case of the restless student with the entrepreneurial spirit. Just a few months later, I got the opportunity to accept an apprenticeship at Remmert Studios which was an incredible break. It was a result of reading a local newspaper article about the business, then going to meet the owner. Not many are able to break into woodworking that easily, especially in the high-end market. That company did a lot of contemporary furniture for churches, and being short-staffed, it wasn’t long before I was given a full-time position.While working that job, I was also taking week-long classes at Marc Adams School of Woodworking as time and money permitted. The combination of hands-on work and classroom study allowed me to acquire new skills very quickly. Being at the school also netted an internship opportunity with one of North America’s most prestigious furniture-makers, Michael Fortune.
In the grand scheme of history, power woodworking tools are a very recent innovation. However, it is hard to imagine modern woodworking without the use of power tools. That being said, one doesn't need a shop full of expensive woodworking machines to be an effective woodworker. When building a workshop, there are seven power tools to focus on first:
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
8.  Making the furniture requires a greater precision of the manufacture than the most other crafts, and so the special attention should be given to measuring and marking. Any incorrectly cut part will result in assembling problems and it will reduce compactness of the whole assemblage. If you make a mistake in cutting on a visible place, it will ruin the aesthetics of the entire piece of furniture or you will have to throw that part away and make it again.
Make It: Paint four clothespins black. Thread a 4-inch-long black chenille stems through the two holes of a large black button. Twist and curl the ends of chenille stems where they meet to form antennae. Glue googly eyes just below the antennae. Next, cut three 3-inch pieces of black stems for each ant. Have your child help you thread all three though the spring hole in each clothespin and adjust to form the legs. Glue the face and two more black buttons to the top of each clothespin. Then use the clips to secure your tablecloth, and enjoy a carefree meal in the summer sun.
Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.
This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.

Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
×