Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
Start by arranging all the parts on your work surface. Justin used a flux brush to spread the glue in the slots, and onto the biscuits after they were installed. Any small brush will work, though. When you have everything assembled, install clamps to hold the sides tight to the shelves while the glue dries. Check by using a framing square or by measuring diagonally from opposite corners to make sure the bookcase is square. Adjust it if needed. Then tighten the clamps. This is a good time to take a break while you let the glue dry for about an hour.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
For large outdoor gatherings, copious seating is a necessity. This outdoor couch can fit several adults, and oversized arm rests act as end tables for drinks. Before getting started, you’ll want to pick up the cushions for the couch first; depending on their size, you can make any adjustments to the cut list necessary for the perfect fit. Once you have the cushions, all the materials you need can be found at local home centers. We used treated lumber, but you can splurge for a naturally rot-resistant wood like cedar or cypress. We’ve got the full plans here.
Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.

Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
The third tool for the beginner is the Jigsaw. A jigsaw allows the user to cut curved and circular patterns in stock. Sure, a band saw will likely be more accurate and can cut thicker stock, but for the beginner, the jigsaw (sometimes also referred to as a Sabre Saw) can be perfectly effective. For versatility, choose an orbital-action, corded jigsaw that feels good in your hand and has an easy blade changing system.

Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood.


Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
There are many textures and materials that can be used for crafting. However, for versatile and affordable crafting, you should think seriously about wood crafts. Craft wood is alluring to crafters first because of its affordable price. When it comes to cheap crafts, wood is the best route. The fact that it is cheap does not mean that it is not useful. In fact, wood crafts are easy to put together, paint and otherwise customize. This means that craft wood has endless possibilities. You can use it in home decor, children's crafts, gifts and much more. For the best selection of wood crafts, you are in the right place. Save on Crafts has crates, boxes, wood burning tools, pine cones and more. Save on Crafts is a discount provider of crafting supplies. This means that you can count on the lowest prices possible with every purchase you make through our store.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Even though I have many large power tools I am still a fan of hand tools, in particular, planes and chisels. In many applications I have found they are the fastest means to an end. Other factors in their favor are their cost. Good hands tools are not cheap, but compared to their motorized counterparts, they are usually much less costly. Another is space. Besides taking up far less space in the shop, they often require less space to use. Think of edge joining an 8 foot long plank. On a jointer you need a minimum of 16 feet of work space. With a hand plane, you move the tool, not the material, so you only need slightly more room than the length of the material.
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
DIY-minded folks, take note. The following websites are chock full of free plans to build tables, storage, beds — you name it. They'll give you the precise information and guidance you need to create furniture that's exactly what you want, for a lot less than what you'll find in stores. Bookmark these and return to them again and again as resources.
Plywood shelves are simple to cut, but look a little thin and can sag over time under the weight of books and other payload. I like to apply a solid hardwood strip of at least 1″ thick to strengthen the shelf and give it a more robust appearance. Cut four strips to 3/4″ x 1″ x 36-1/4″ (slightly longer than the shelf itself, allowing you to trim flush later). I attach this strip by simply gluing and carefully clamping for good alignment, gluing the 1″ thickness to the plywood. In the past I have also used biscuits or brads for attaching the strips, but I have found it to be unnecessary, and the method I currently use delivers great results every time. Use a lot of clamps to ensure a good bond between the plywood and edge strip. Carefully force each surface flush as you move from clamp to clamp. If you are careful here, you can save yourself a lot of sanding effort later.

My parents have the space and Dad has the tools -- a drill press, forstner bits and a long workbench were pretty essential. We decided to use countersunk 2x4s as uprights. This eliminated the need for pricey cap/acorn nuts while still leaving the all-thread ends 'protected' on the outside and allowing us to put it flush against the wall without causing damage.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.

How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.
The jigsaw, another hand held and versatile saw, is used for cutting curves. One has a lot of freedom with a jig saw because it can cut curves, circles and straight. Depending on the width of the blade, the curves can be very fine. The down side to the jigsaw is that straight lines can be difficult depending on the wood you are cutting. No matter, it is important to make sure to always have sharp blades.
Storage can never be enough for a home with children. Especially if the family is midsized to a large one! A headboard with optimum storage space is an ideal solution in children’s room to accommodate most of their belongings, so that they can have an easy access to them on a daily basis, and not litter them everywhere. The headboard can be revamped for them, according to their choice of colors and need.
×