Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.
4. Selection of furniture plan: Before you start making furniture based on some plan, analyze it thoroughly. Make sure if the furniture plan has all the necessary dimensions and informations, and is it made properly. A bad and incomplete furniture plan will result in the poor quality of the final product and you will spend more money finishing it. If the dimensions of the furniture pieces do not match and you realize that only during its assemblage, you will have to throw away all the material, not to mention the time that you’ve lost with it… Choosing a quality furniture plan is another basic requirement to make the quality furniture.

While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.


The content of this website, TheArtofHomeRenovations.com, and its associated social media pages, is provided for informational purposes only. The information is not intended as, nor should it be considered a substitute for professional claims, suggestions, diagnosis, or counseling of any kind under any circumstances. By reading this website, you acknowledge that you are responsible for your own decisions. Do not take information from any website, including this one, and try it without proper research and supervision. For more information, please read our Privacy Policy.
A mechanical reasoning or aptitude is also essential, mainly because woodworkers work with such a variety of machines and tools.  A tool in the hands of an untrained or inexperienced woodworker is a recipe for disaster. Woodworkers should understand and be able to apply mechanical principles to solve any problems they may encounter. Critical thinking skills are important too as woodworkers may face unexpected problems that need to be handled quickly. In this way, woodworkers can use reasoning and logic to foresee any potential problems, and develop solutions before mishaps happen.
DIY-minded folks, take note. The following websites are chock full of free plans to build tables, storage, beds — you name it. They'll give you the precise information and guidance you need to create furniture that's exactly what you want, for a lot less than what you'll find in stores. Bookmark these and return to them again and again as resources.
Thickness planer. A thickness planer is used to fix surfaces of imperfect wood. If you are picking up less than perfect wood from the lumberyard, wood with some surface defects, a planer will let you fix that wood in the quickest time. A thickness planer pays for itself quick as it allows you to buy cheaper wood that doesn’t have perfect surfaces and fix it yourself. Be careful though. You loose wood during planing. So the remaining amount of wood still has to be worth the price you paid for it.
×