The content of this website, TheArtofHomeRenovations.com, and its associated social media pages, is provided for informational purposes only. The information is not intended as, nor should it be considered a substitute for professional claims, suggestions, diagnosis, or counseling of any kind under any circumstances. By reading this website, you acknowledge that you are responsible for your own decisions. Do not take information from any website, including this one, and try it without proper research and supervision. For more information, please read our Privacy Policy.

Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
The most common bench tools in the woodshop are routers and sanders. We have already talked about routers to some extent. Orbital sanders have come a long way from the jitterbug style of old. New sanders leave a better finish, are quieter and last longer. At some point, probably right away, you will want a sander . No one likes to sand. It is tempting to buy multiple sanders to address an unpleasant task. Here again, I point to the hand tools. Learning to use a smoothing plane and a cabinet scraper will reduce your sanding to little or nothing and cut down your overall time to finish a project.
All things considered, the easiest and most practical way to plane a piece of unmilled wood is to use a router. You can pick up a halfway decent router fairly inexpensively, and the good thing about investing in one is that there’s truly no limit to what you can do with it - planing a piece of wood is just one of a million different things a router can be used for.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud. 

Do you often get intimidated by woodworking? With all the tools available, the problem here is that many don’t know what wood power tools to use. Woodworking has a variety of specialized tools for different tasks. Knowing which ones to pick is important to make woodworking easy and enjoyable. If you have no idea about power tools, this will definitely help you out.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Since money and space are usually in high demand, you want your purchases to make sense and work for you as far into the future as possible. To do this, the focus should be how to expand your capabilities rather than getting one project done quickly. With this in mind, and based on what I've learned over the past three decades, here's how I would proceed if I were starting over now.
Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
Thank you for sharing your story! Would love to hear how you got started with your blog and business too someday, I always find it so interesting what inspires people to shift their career path. I can’t believe you’ve learned so much with YouTube videos! And congrats on creating such a successful business from scratch and also having the courage to walk away when you knew it wasn’t for you anymore. We’re having a home built next year, so look forward to checking out all the custom work you’ve done with your place!
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
So what is it about starting a woodworking school? It seems that every time I open a woodworking magazine, there is yet another ad for a new woodworking school - usually run by a furniture maker. They're probably thinking, "It can't be that hard, right? I know how to make furniture, I have some tools and I can keep doing my own furniture. But I can attract students and teach them anything they want to know at the same time?"

Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.


Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.
At the same time, in order to improve your skills, you have to first use those skills and will make mistakes as a novice. How quickly those are overcome and improved on varies from person to person. Some craftsmen grasp a skill quickly and progress to higher levels, others, for several reasons, take more time. Those that do this quickly thrive as self-taught artisans.
Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
In recent years, this versatile and accurate tool has become a fixture in the work shop and at the work site. Also called a “chop box,” the miter saw consists of a powerful circular saw mounted on an arm that hinges at the rear of the tool. When the blade is lowered in a chopping motion, it cuts through the workpiece, passing through a slot in the base. The motor and blade can be pivoted with respect to the base for miter cuts. Another adjustment makes it possible to tilt the blade, too, allowing for compound miter cuts, handy for jobs like cutting crown moldings, which are set at a pitched angle and that must also turn around corners. The diameter of the blade determines the maximum cut width, with standard sizes ranging from 8-inch blades up to 15 inches. A 10- or 12-inch saw is sufficient for most jobs.
The Japanese saw is a favorite. A much smarter, efficient and exact cut can be made using this saw as opposed to a European saw. The difference between the two is simple: tooth direction. European saws cut when pushing the saw as opposed to Japanese saws which cut on the pull. One uses much less energy when pulling - perhaps that is why the horse was put in front of the cart. A Japanese saw is a must have in any shop.

Thickness planer. A thickness planer is used to fix surfaces of imperfect wood. If you are picking up less than perfect wood from the lumberyard, wood with some surface defects, a planer will let you fix that wood in the quickest time. A thickness planer pays for itself quick as it allows you to buy cheaper wood that doesn’t have perfect surfaces and fix it yourself. Be careful though. You loose wood during planing. So the remaining amount of wood still has to be worth the price you paid for it.
×