Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.
You can make your bookshelf any size you’d like, but a standard size with even proportions is about 12 inches deep, 30 inches wide and 48 inches tall. That's big enough to hold books and magazines, but not so big that it won't fit where you want it to. Note: If your shelves are any longer than 32 inches, you'll need thicker lumber or midspan supports so the shelves won't sag when they're filled with books.
Using these bookcase plans, I built three of these for my children’s school about five years ago (five years in an elementary school is equivalent to a hundred years in a typical home). They have seen tons of abuse, and have held up beautifully. The school can’t wait to get their hands on more of them to replace the “bargain” bookcases they got from a furniture chain which have needed extensive repairs over the same five year period. 

I am from pittsburgh and I make a lot of my projects out of pallets from blanket chest to nautical lamp post and they both sell well here wine racks are Good sellers in the fall and winter months bird houses in the spring it seems what’s the best time of year and the rite product to build I lucked out and I am busy all the time and I can’t forget my best seller is a Raised doggie feeder and water tray with a bone I cut out and it hangs on the front of the tray with 2 small chains and can be personalized with the pets name on it I love to up cycle wood and keep on building
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Another fine example of remodelling furniture and re-using what already exists in the house.  The bookcase involves using your old kitchen cabinets, and building new shelves on top of them. The final product can also be used as an entertainment unit, housing a television, books and things of your interest along with ample storage to keep other utility objects.
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period. Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
Adjustable shelves beat fixed shelves in just about every way. They make storage and display space more versatile, of course. And they’re usually just slabs of plywood nosed with strips of wood or edge banding, so they’re easy to make. And because you can remove them, adjustable shelves simplify staining and finishing. The easiest way to support adjustable shelves is by using shelf standards are ($3 for 6 ft. at home centers). Just screw them into place and you’re done.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!

Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
10.  While manufacturing the furniture, another important thing besides the precise parts manufacture is the assemblage. The pieces, when fitted, should come together easily, and not require to be twisted, sprung or bent in order to put the piece article together. It is the practice with skilled cabinet maker to put a piece of furniture completely together once (without glue, screws or nails)to see that everything fits right, before putting together permanently. After fitting the parts of a piece of furniture and before gluing, smooth such parts as cannot readily be smoothed after putting together permanently.
Although a mobile tool, it is recommended to set the compound miter saw in place with extended tables on both ends. This saw makes very quick and accurate cuts, allowing for compound cuts.  In addition to the rotating table, the compound milter saw has a rotating vertical pivot which lets the cutter head and blade to be tilted sideways, allowing both vertical and horizontal cuts to be angled on both planes.
After experiencing working in the wedding rental industry, I knew it wasn’t something I wanted to do long term and sold my business. My wedding and vintage rental business had reawakened my creativity though. After learning how to build farm tables, I became hooked on building and making things. And knowing how to build other things became much easier, as well as learning to use different tools. It’s like once you know how to do one thing related, the rest just flows.
This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.
Someone interested in woodworking now needs to get computer training to be able to lay out jobs on a CAD program. CNC machines are also used in shops where they lay out the cabinetry for you and cut the parts. Working with these machines takes skill in knowing how to build the cabinet and knowing how to use the computer programs. Also, math is used all day, every day in woodworking, and the better you are at math the better you can build things.
A small jointer is better than no jointer, but a small jointer is not a great addition to a shop. A jointer needs table length. I would skip buying a small to medium size jointer. Once again, rely on your hand tools. They can perform as well or better than a machine that costs hundreds more, they require a great deal of room, and they should be run in conjunction with a dust collector. You can flatten boards with a jack plane and straighten edges with a jointer. With a little experience it becomes a quick task.
×