Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.

After investing a number of weekends building a nice table or chest, how are you going to finish it? Finishes beautify and protect the piece you’ve worked so hard to build so don’t cop out and do the “rub it with oil” thing. There are so many beautiful finishes that become second nature to work with. I use shellac 99% of the time. Once you get the feel down, it’s really quick to apply, very forgiving, easily repairable, and you never have to clean a brush (because it re-softens in alcohol)! There are other varnishes that provide good protection for outdoor use as well. I recommend picking up a good starter book, like Jeff Jewitt’s Hand Applied Finishes. It is simple and straightforward, without getting too far into minutiae.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.

The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Drill presses are available as both freestanding floor models and in benchtop designs. The drill press is powered by an electric motor, driving it via a system of pulleys or gears. The drill bit is locked into the chuck, then is driven down using a hand-powered lever system. A spring pushes it back up when pressure on the lever is released. The size of a drill press is determined by the throat, the distance between the supporting column at the rear and the axis on which the spindle of the drill turns; thus, a 15-inch model will cut to the center of a 15-inch workpiece. A number of adjustments including a movable table depth, a depth gauge to set the distance the spindle travels and pulley adjustments to change speeds increase the tool’s functionality. The drill press can be used not only to drill round holes of all kinds but also for sanding, grooving, and even mortising jobs with the addition of specialized attachments.
Click HERE or on the image below for the downloadable Double Chair Bench Plans. These plans are 100% free and you have the option to donate at the time of download to help support DIY PETE so he can devote more time in creating FREE video tutorials and plans for you. This is 100% optional of course! If you’d like them for FREE simply enter “0” in the dollar amount   Cheers! – Pete
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Clamps. Woodworking clamps are essential when building a project. They hold the components together while assembling them together, gluing them, during measuring, cutting et cetera. Be generous with the number of clamps you purchase because you will always need more than you think, and it gets difficult to assemble the project if you do not have enough clamps.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
You could also go old school and use a combination of hand planes. Hand planes of course are much less expensive than a big power tool like a planer, but their drawback is they require a lot of skill, practice, and patience to achieve good results. If you’ve got the time, there’s absolutely no substitute for learning how to hand plane, and you’ll quickly earn the respect of your fellow woodworkers.
Clamps. Woodworking clamps are essential when building a project. They hold the components together while assembling them together, gluing them, during measuring, cutting et cetera. Be generous with the number of clamps you purchase because you will always need more than you think, and it gets difficult to assemble the project if you do not have enough clamps.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.

It wasn't until the end of the eighteenth century when the first woodworking machine was patented. Some of the basic principles of the earliest woodworking machine tools are still in use today, but the new machines are faster, more powerful, and easier to use than previous generations. We carry a full range of stationary woodworking machines including table saws, miter saws, band saws, drill presses, mortisers, shapers, planers and more. If you have any questions or need help finding what you need, give us a call or email and we'll assist you in finding the right woodworking machine.

The best advice I could give you is to learn WordPress or find a friend who can help you figure it out. Once the light bulb goes off there will be no stopping you, you will have the power in your own hands to provide what your end user needs and to educate them about the benefits and your products value – in a selfish, wasteful, throw-away society who expect everything delivered yesterday and expect to pay dirt cheap prices for your skills and repetitive hard work. End of rant….Sorry but I just had to comment. I know what it’s like, don’t lose hope!


Some might expect to see a cordless drill on this list, but when we're talking about basic power woodworking tools, a corded drill is more versatile and powerful. Sure, the cordless is, well, cordless, which makes it more portable, but corded drills are less expensive and can do more than a cordless drill. There are some options to consider when choosing a corded power drill, such as whether you want a 3/8-inch or 1/2-inch chuck, keyed or keyless chuck, straight drill or hammer drill, and so on. Learn all about these options (along with some suggestions on what to look for when shopping) in this article on corded power drills.
The circular saw is a hand held or table mounted saw. Circular saws come with the ability to set the depth of the blade, which enables one to create cut offs, dados and narrow slots. There are upsides and downsides to all saws, and the one down side to the circular saw that its light weight sometimes causes it to move when cutting, and stability in the machine is important for the cut and for safety. On the other hand, this is also its advantage. The versatility and the mobility of this saw gives one the freedom to work anywhere.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
In my opinion, there are two kinds of woodworking. One is fine woodworking which is well worth learning and mastering. It just takes more time, skills and know-how. Second, there is basic or “maker” woodworking which is probably where you want to start. Find something that will help you jump in and gain some confidence with some basic tools and projects. Then, if you want, graduate to fine woodworking.
· Each plan contains a clear and colourful scheme, so no guessing is required. It depends on the level of detail; the most demanding projects will take you to the park! If the instructions are clear, the project is built on its own. All pieces are “clicked” and put in place. It is also suitable for beginners. A skilled woodworker can complete the project in less time than usual ones.

Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.


Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results. 

You can make your bookshelf any size you’d like, but a standard size with even proportions is about 12 inches deep, 30 inches wide and 48 inches tall. That's big enough to hold books and magazines, but not so big that it won't fit where you want it to. Note: If your shelves are any longer than 32 inches, you'll need thicker lumber or midspan supports so the shelves won't sag when they're filled with books.
A tri-sectional bookshelf, with sufficient space to house books or can be used for storage too. Its low level design can be dually used as a bookcase as well as a bench. So, one doesn’t need to walk to a bookshelf situated in some area of the house, to grab a book, but can sit on this bench and pull one out from the lower section. How convenient is that!
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.

Turn leftover wood or old pieces of furniture into DIY reclaimed wood projects! Wood is one of my favorite materials to work with. The possibilities are endless and they give such a homey and cozy feel to any rustic home. My husband, Dave, and I sometimes even go the extra mile and carve our initials on a little spot. It’s our own way of making our DIY project even more personal! Here’s a list of some of our favorite DIY reclaimed wood projects!   


However, I would recommend that you either build a wooden workbench, or purchase one if you feel a workbench build is too advanced for you right now. However, I created the DVD “Building the Portable Moravian Workbench with Will Myers” so that even beginners can build a solid, portable, and very affordable workbench that will fit almost anywhere, using mostly or only hand tools. You can buy it in my store here. You can find Will’s free workbench plans for the Moravian Workbench here. Whichever path you choose, make sure you choose to either build or buy a heavy & sturdy wooden workbench, with at least a 3″ solid top, strong supportive base legs, and two strong vises.
And with many homes falling into the “contemporary but traditional’ style that has taken over the decade, these wine racks are in high demand and can fetch a pretty penny for even a more simplistic design.Feel free to get creative with the design for some more bargaining power. And for a design to hold a small number of bottles, you can expect up to $50 per unit sold.
Kids love to watch grown-ups use woodworking tools, but what they love even more is making the sawdust fly themselves. With minimal equipment and adult help, your child will soon be turning out a wonderful variety of toys, games, gifts, household objects, and holiday decorations. These 50 easy and inexpensive projects are arranged by age and skill level.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
×