A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
In the grand scheme of history, power woodworking tools are a very recent innovation. However, it is hard to imagine modern woodworking without the use of power tools. That being said, one doesn't need a shop full of expensive woodworking machines to be an effective woodworker. When building a workshop, there are seven power tools to focus on first:
4. Selection of furniture plan: Before you start making furniture based on some plan, analyze it thoroughly. Make sure if the furniture plan has all the necessary dimensions and informations, and is it made properly. A bad and incomplete furniture plan will result in the poor quality of the final product and you will spend more money finishing it. If the dimensions of the furniture pieces do not match and you realize that only during its assemblage, you will have to throw away all the material, not to mention the time that you’ve lost with it… Choosing a quality furniture plan is another basic requirement to make the quality furniture.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
Historically, woodworkers relied upon the woods native to their region, until transportation and trade innovations made more exotic woods available to the craftsman. Woods are typically sorted into three basic types: hardwoods typified by tight grain and derived from broadleaf trees, softwoods from coniferous trees, and man-made materials such as plywood and MDF.Typically furniture such as tables and chairs is made using solid stock, and cabinet/fixture makers employ the use of plywood and other man made panel products.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).

The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.


Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.

I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.
Make It: Paint nine craft sticks red, six craft sticks white, and four mini craft sticks white. Let them dry. On a rectangle piece of cardstock, have your child create a blue sky and green grass with colored paper or markers. Then help her create the bottom of the barn by gluing on a row of 11 craft sticks vertically in the following pattern: two red, one white, five red, one white, two red. Glue white sticks horizontally along the top and bottom and cross two in the middle as shown. Glue the mini craft sticks to red cardstock to form the barn roof. Adhere the barn roof to the background above the barn. Cut out a rectangle from black paper and adhere it to the barn. Cut strips from a paper bag and crumple for the look of hay; adhere to black rectangle.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
Use the Cutting List (see Additional Information, below) as a guide for cutting all the parts. The next step is to mark the shelf positions on the shelf sides. It’s important to keep track of the orientation of the parts. For reference, we placed a piece of masking tape on the top of each side, and on the top side of each shelf. Justin and Jackson used a framing square to draw lines indicating the bottom of each shelf (Photo 1).

Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.
Jim, I belong to Charles Neil’s website and get his DVDs and watch his videos. He’s a great teacher. However, if I had to travel all the way up to Virginia I’d be out of luck. The Internet is a great asset for woodworkers. BTW, I wish the college you teach in was right here in my town. If it were I’d enroll because I know that you are a fine woodworker. Traveling somewhere to a class is an expense that I couldn’t afford in money and time.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Make It: Help your child paint a square wooden dowel and wooden spool his favorite colors and allow to dry. Glue white string around the spool and adhere it near the bottom of the dowel. Attach a long string to the far end of the dowel and tie a magnet to the opposite end (magnetic barrels from the jewelry section of the craft store work well). Make clothespin "fish" by painting them fun colors with pink lips. Let paint dry and help your child glue on sequin scales and googly eyes. Now he'll be ready to go fishing!
Power Tools — A good table saw is usually the most used machine in the shop. New saws have vastly improved fences and better safety features. A good contractor saw has adequate power and can come with up to 49" of ripping capacity to handle sheet goods. This would be my first big purchase. A router is often a highly coveted machine. There are almost endless cutters available now and it is hard to argue with their versatility. I recommend looking at the combo packages that include a plunge base. It is a good way to get two machines for the price of one. In my opinion, an elaborate router table is not necessary for most applications, nor are the expensive and bulky jigs and templates for making joints. What tends to happen is the tools start to drive what is made. Drawers start to fit the machine or template instead of the piece of furniture. Sufficient joints can be made with the table saw, by hand, or you can make your own templates to fit your project.

The circular saw is a hand held or table mounted saw. Circular saws come with the ability to set the depth of the blade, which enables one to create cut offs, dados and narrow slots. There are upsides and downsides to all saws, and the one down side to the circular saw that its light weight sometimes causes it to move when cutting, and stability in the machine is important for the cut and for safety. On the other hand, this is also its advantage. The versatility and the mobility of this saw gives one the freedom to work anywhere.
These are without a doubt the most adorable things ever. The fact that you make them with coffee filters and they are cheap does not cloud my judgment, either. They are really easy to make though and so creative. These coffee filter pom poms would look so adorable hanging in a little girl’s bedroom or just anywhere that you want a bit of decoration. You can use them to decorate the deck for summer parties or make really large Christmas ornaments from them. Either way, you just need disposable coffee filters, some hot glue, sturdy cardboard and string and you can find the tutorial over at Bored & Crafty.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.
The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later. So I measured my books before I decided how tall the shelves should be. As a rule, a bookcase with shelves between 7 in. and 14 in. apart accommodates most everything. While books generally fit on 8- to 9-in.-deep shelves, I prefer deeper bookcases, so I ripped the plywood to a width of 11 7/8 in.
Ultimately, to be a woodworker, just start doing it. Read about it, watch it on television, accumulate tools, look for openings of any kind in a shop, a sawmill, a lumberyard, any place related to the woodworking business. Start making things. Learn carpentry. A good cabinetmaker should also be an excellent carpenter. Build up a portfolio of work, and acquire skills and knowledge any way you can.
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.
here's my 6x6 version build with #2 pine. shelves are 1x10 and threaded rod upsized to 5/16" to allow for extra width. center upright spaced at 1/3 side to side. this is very complex structurally - all the commenters who don't believe it should build it to really feel how it works. it is basically like a post-tensioned high rise. i think i'd like to paint the uprights and stain the shelves.
Formally known as a “tilting arbor saw,” this tool is just an upside-down electric handsaw that’s been mounted to the underside of a steel table top, with the circular saw blade protruding through a slot. The “arbor” is the shaft on which the blade spins. It’s an axle that can be tilted with respect to the horizontal table top for cutting angles; it’s raised or lowered to adjust cutting depth. A miter gauge enables the sawyer to push stock at angles or perpendicular to the blade (“cross-cutting”). A fence can be fixed parallel to the blade for cutting along the length of a workpiece (“rip-sawing”).
The router is a hand held tool which is often mounted upside down and is used to hollow out an area in the face of a work piece. It is also used to cut profiles for moldings and adding decorative edges to any piece enhances its beauty and dimension. Routers are also used to cut joinery, such as dovetails and dados. The beauty of a router is that one can purchase an unlimited number of profiles to best suit the many requirements which arise with woodworking.
This bookcase plan is designed to be large enough to handle all of the books belonging to the voracious reader in your family, virtually indestructible to withstand years of abuse, and easy on the pocket book using inexpensive materials from your local home center. For about $100 you can have a bookcase that would cost $600 – $800 at a retail furniture store.
Use the Cutting List (see Additional Information, below) as a guide for cutting all the parts. The next step is to mark the shelf positions on the shelf sides. It’s important to keep track of the orientation of the parts. For reference, we placed a piece of masking tape on the top of each side, and on the top side of each shelf. Justin and Jackson used a framing square to draw lines indicating the bottom of each shelf (Photo 1).
Today, in our age of plastic and factories, woodworking has transformed from a common necessary skill into something almost mysterious or awe-inspiring. Because most 21st-century consumers are used to driving to big box stores to pick up another mass-produced replacement when their desk falls apart or their chair breaks, any man today that can walk up to a lumber pile with saw and plane to shape a beautiful and enduring replacement is revered as a “true craftsman.”
My whole life, I’ve loved to be creative and make things. Once I got older though, creativity and anything art related really got pushed aside for a more serious career path. After graduating from college, I decided to go to grad school, get my MS in accounting, and then I became a CPA (Certified Public Accountant), and started working in accounting for several years.
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.
Clamps. Woodworking clamps are essential when building a project. They hold the components together while assembling them together, gluing them, during measuring, cutting et cetera. Be generous with the number of clamps you purchase because you will always need more than you think, and it gets difficult to assemble the project if you do not have enough clamps.

If you have an old guitar lying in your house that you just don’t want to let go of, due to an emotional attachment, here is a great way of re-using it, by converting it into a bookcase. Whether you hang it in your living room or in your courtyard, it looks really attractive, housing your favourite reads. If one can arrange for a hammock, the entire setting of your courtyard will look splendid!


11. Other necessary skills: Each woodworker should have a basic knowledge of metalworking. Although most of the home furniture is made out of wood, in this category you may occasionally find some projects made out of metal, or the wooden furniture projects that have a decorative metal parts or fasteners. In our opinion, the combination of wood and wrought iron makes the most beautiful furniture.
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
These are without a doubt the most adorable things ever. The fact that you make them with coffee filters and they are cheap does not cloud my judgment, either. They are really easy to make though and so creative. These coffee filter pom poms would look so adorable hanging in a little girl’s bedroom or just anywhere that you want a bit of decoration. You can use them to decorate the deck for summer parties or make really large Christmas ornaments from them. Either way, you just need disposable coffee filters, some hot glue, sturdy cardboard and string and you can find the tutorial over at Bored & Crafty.
With your tools set up and ready to go, you’re ready to get started on woodworking projects. If you’re looking for beginner woodworking projects, we’ve got you covered. Projects range from birdhouses to jewelry boxes; there’s something for everyone. You’re sure to find a project that’s a good fit for your skills and tools, and that you’ll enjoy creating.
Do you often get intimidated by woodworking? With all the tools available, the problem here is that many don’t know what wood power tools to use. Woodworking has a variety of specialized tools for different tasks. Knowing which ones to pick is important to make woodworking easy and enjoyable. If you have no idea about power tools, this will definitely help you out.

Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.

Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.


Maybe you have a tablesaw and a 13” thickness planer already, but most of us don’t. Be careful not to fall into the trap of feeling like you have to buy expensive machines to build things. When I work with wood, I use only hand tools and love every minute of it. If you learn how artisans worked their lumber before machines dominated the furniture industry, you will find woodworking by hand to be efficient and viable. There are many tried-and-true techniques to expedite the process that free us from feeling like we have to do machine-perfect work by hand. The real key is to use the right tool for the job: coarse tools for coarse work and fine tools for fine work. Still not convinced? Check out my good friend Jim’s story. I hope it inspires you.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.

When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
Break down plywood Following the cutting diagram, crosscut plywood along the line marked “first cut”. Take the smaller of the two rip 3/4″ plywood according to diagram and cut list. For safety and easier handling, use a circular saw with a good quality blade (following a straight edge guide for a straight cut) for first cross-cut on plywood. If you are not confident in your circular saw’s ability to cut straight lines with no tear out, leave yourself 1/4″ of extra material (there is enough extra material in a 4′ x 8′ sheet of plywood to do this) and make your final cuts on the table saw.
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
I always try to ask my students why they have come to my school. The standard answer is, "I wanted to learn the right way," but frequently the answer is "that I sit in front of a computer all day and don't feel like I do anything at all." Or simply, they are bored with sitting at home every night. These are the people who are really fun to have in class. They have no preconceived notions, no bad habits to break and they usually really appreciate whatever they have made. Many of them go on to make some new friends at the school. Through the years, I have seen many make plans to take another class "if my buddy is going to do it, too."
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
×