Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
Apply 2 coats of Urethane with a brush. Let the second coat dry completely (6-12 hours), then lightly sand the armrests, table, and areas you come in contact with when sitting (chair slats). This light sanding with 220 grit paper will remove any dust particles that settled in the first coat. Next, take a clean cloth and wipe a thin coat of poly on all the areas you sanded. This will give you a nice smooth finish. Once dry, enjoy your new furniture and have a barbecue!
Manufacturing the furniture is one of the most complex crafts, because manufacturing the good quality furniture requires a lot of skills, tools and rich experience. As the part of interior, the furniture is always on the visible place and it is often the main element of interior decorations. Because of this, its manufacture does not allow any mistakes. Just a tiny error on a visible place can often ruin all the effort that was made to produce that piece of the furniture. Because of that, a quality furniture plan is one of the basic things for reducing the risk of errors.

Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)

If you are like most woodworkers, you will end up with a few large machine tools, some smaller ones and a collection of much-needed hand tools. However, the tools you should have in your wood shop (especially if you are starting afresh) depends a lot on the kind of woodwork you will make, the amount of space you have and the amount of money you will spend at the moment.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
There are several ways to complete this task, including pocket screws, brads or biscuits. I have used all of these methods, but my preference is biscuits, as they provide adequate strength, excellent alignment, and ease. I generally just place one biscuit in the center of each rail and stile, which provides alignment assistance while not being overly constraining when manual adjustments need to be made to achieve desired placement. After applying glue and biscuits, use lots of clamps to create a gap-free bond between the face frame and carcass.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
I decided to start my own vintage rental company, with farm tables being the main rental item. There was just one problem, I couldn’t afford to buy twenty farm tables… Which led me to my only option, I’d have to build them, except that again I didn’t know a thing about building or power tools nor did I know anyone that I felt comfortable asking to teach me. But, I figured if I could pass the CPA exam, I could figure out how to build a table on my own and learn how to use power tools.
Another fine example of remodelling furniture and re-using what already exists in the house.  The bookcase involves using your old kitchen cabinets, and building new shelves on top of them. The final product can also be used as an entertainment unit, housing a television, books and things of your interest along with ample storage to keep other utility objects.
×