Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
Fifteen years ago, I was running a small woodworking school in a funky L-shaped room with a leaky roof (try keeping a straight face when water is dripping on your head while you demonstrate how to use the table saw). As much as I liked working at the architectural millwork firm, I realized the school would always take a back seat to the main focus of the business.
Using these bookcase plans, I built three of these for my children’s school about five years ago (five years in an elementary school is equivalent to a hundred years in a typical home). They have seen tons of abuse, and have held up beautifully. The school can’t wait to get their hands on more of them to replace the “bargain” bookcases they got from a furniture chain which have needed extensive repairs over the same five year period.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.

Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
It’s mostly been learn by doing for me. I can’t afford to go somewhere to take any lessons. However, I do learn from books, DVDs, and videos on the internet. I still believe that learning by doing is the best way. Books and videos can get you going in the right direction but when you do it on your own all kinds of problems crop up that you have to solve. For example, when woodcarving the best way to understand what carving with the grain is is to carve with a carving tool. Same thing about sharpening a carving tool. You had better learn how to sharpen by sharpening your tools when they need it. You’re dead in the water if your carving tools are not sharp.

Build a model boat. Model boats are a bit tricky to shape and it's best to find individual patterns for these, depending on the type of boat you're after. A very basic one can be made from a rectangular block of wood with a dowel hole drilled in the center, a dowel inserted for the sail pole and a sail (cloth or paper) attached to the dowel pole. It's not the most elegant but it's quick and simple, and from there, you can start building more advanced versions.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
At some point dust collection needs to be considered. For safety reasons all power tools should run in conjunction with a good dust collection system. However the reality is that many woodworkers will put up with the dust for a while, if not forever. There are machines that really can't be run without dust collection such as a large planer or a bandsaw. The chips and sawdust must be extracted or else the buildup will damage the machine. A large shop vac may be sufficient for smaller machines, and portable dust collectors are available that can be moved from one machine to another. Dust collection is a reasonable investment that should actually be made early on. Your health is well worth the cost.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.

There is significant evidence of advanced woodworking in Ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2


Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.

As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
Picture it: eight people with different skill levels, each trying to design a different project (which, by the way, they have no idea how to do) and hopefully cutting some wood by the third class. Meanwhile, the instructor is running from student to student, and then running to the table saw where a kickback has occurred. It is no wonder that at the end of the class not a single thing has been made and most of the students don't come back.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create. 

It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.
Choose a suitable area to do your woodwork crafting in. You'll need sufficient area to move about in, which includes considering the lengths of wood you'll be working with and the types of tools and even machinery you need to set up. As well as space for you to work within, there will also need to be sufficient space to store the wood, the tools and other related items so that they are easy to find and are kept inside, away from the elements.
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.
At the same time, in order to improve your skills, you have to first use those skills and will make mistakes as a novice. How quickly those are overcome and improved on varies from person to person. Some craftsmen grasp a skill quickly and progress to higher levels, others, for several reasons, take more time. Those that do this quickly thrive as self-taught artisans.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
Adjustable shelves beat fixed shelves in just about every way. They make storage and display space more versatile, of course. And they’re usually just slabs of plywood nosed with strips of wood or edge banding, so they’re easy to make. And because you can remove them, adjustable shelves simplify staining and finishing. The easiest way to support adjustable shelves is by using shelf standards are ($3 for 6 ft. at home centers). Just screw them into place and you’re done.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
Lots of ways. Woodworking really reinforces my independent nature. Blogs are good. Norm Abrams videos. I have a library of magazines and books with really neat projects which I love to read over and over to get a sense of how other woodworkers think through their creative projects. I have a painter friend with whom I endlessly brainstorm how to finish the final wood project. But really, the wood itself teaches me the most. Each species has different needs. The projects also teach me. Each project is unique in approach, design, and method. I’ve learned to listen and make myself a servant of these things. I come to the shop ready to learn.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking. 

Offer good for one item at regular price only. Limit one coupon per customer per day. Must present coupon at time of purchase. Offer is not valid with any other coupon, discount or previous purchase. One cut or one bolt of fabric or trim "by the yard" equals one item. Online fabric & trim discount is limited to 10 yards, single cut. Excludes CRICUT® products, candy & snack products, gum & mints, gift cards, custom orders, labor, rentals, class fees or items labeled "Your Price". Exclusions subject to change. Cash Value 1/10¢.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.

Of course, there’s the occasional install, client meeting or photo-shoot, but those don’t happen often enough to be considered a typical day. I should mention that every day brings its share of phone conversations with clients and suppliers. That happens at all hours. Most work days end by 7:30pm, and once I’m home and have eaten supper, I’ll usually put another hour into handling whatever financial, legal or internet tasks are most pressing at the time. Altogether, a typical work day is about 12 hours, and this is 6 days a week. At 2 1/2 years old, the business is still a start-up which is the reason such long hours are necessary.

Power Tools — A good table saw is usually the most used machine in the shop. New saws have vastly improved fences and better safety features. A good contractor saw has adequate power and can come with up to 49" of ripping capacity to handle sheet goods. This would be my first big purchase. A router is often a highly coveted machine. There are almost endless cutters available now and it is hard to argue with their versatility. I recommend looking at the combo packages that include a plunge base. It is a good way to get two machines for the price of one. In my opinion, an elaborate router table is not necessary for most applications, nor are the expensive and bulky jigs and templates for making joints. What tends to happen is the tools start to drive what is made. Drawers start to fit the machine or template instead of the piece of furniture. Sufficient joints can be made with the table saw, by hand, or you can make your own templates to fit your project.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!

However, I would recommend that you either build a wooden workbench, or purchase one if you feel a workbench build is too advanced for you right now. However, I created the DVD “Building the Portable Moravian Workbench with Will Myers” so that even beginners can build a solid, portable, and very affordable workbench that will fit almost anywhere, using mostly or only hand tools. You can buy it in my store here. You can find Will’s free workbench plans for the Moravian Workbench here. Whichever path you choose, make sure you choose to either build or buy a heavy & sturdy wooden workbench, with at least a 3″ solid top, strong supportive base legs, and two strong vises.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
When it is time to make a purchase, is it better to compromise and get an undersized machine that will only improve our capabilities by a small degree? After 30 years of working wood, my shop is equipped with several large, heavy machines that I greatly enjoy having and using. If I had to do it over, I personally would skip most of the interim-sized machines that did not serve me well and I would wait for the time when I could afford and have room for the right machine. In the meantime, I could still be productive with a smaller, but carefully selected group of the right hand tools and power tools.
We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
These are without a doubt the most adorable things ever. The fact that you make them with coffee filters and they are cheap does not cloud my judgment, either. They are really easy to make though and so creative. These coffee filter pom poms would look so adorable hanging in a little girl’s bedroom or just anywhere that you want a bit of decoration. You can use them to decorate the deck for summer parties or make really large Christmas ornaments from them. Either way, you just need disposable coffee filters, some hot glue, sturdy cardboard and string and you can find the tutorial over at Bored & Crafty.
It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
Once you’ve mastered the basics, then check out magazines like Fine Woodworking, Woodcraft, etc. Visit your local woodworking store (like Woodcraft or Rockler) and browse the book / plans section. What I like is these stores normally have people with woodworking expertise and can answer most of your questions whether they be basic or advanced. They also offer monthly workshops at an affordable price.
I know this is an old forum topic, but I felt the need to chime in. I was in Jr. High back in the late 70s and my school had a wood shop and I still have a cutting board and a three leg single post foyer table made from those shops and very proud of them. It is sad seeing the lack of “hands on” classes these days in schools because of liability issues. Just recently got back into woodworking last year and honestly Marc has much to do with that and his YouTube videos, that and a date night where my wife and I went to a Woodcraft class for making pens. I plan on joining the guild at some point but wanted to get enough tools and skills together to make the guild worth it for me and I am almost there. I am currently working on the 2015 Kids Table from Woodworkers Fighting Cancer and will donate to them as well when I finish even though it is way past due it is the perfect project for my daughter. Since I started I have made pens, cutting boards, a toy airplane and now working on this table and love it. Thank you Marc for being such an influence on this community!!
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
It could be a pun about family life, or a comment on whatever pets have currently made their territory. People love these simple decorations right next to their front doors.With just a board, a little creative painting, and some simple small hooks, you can find yourself around $15 per holder, all for around 30 minutes of sanding, cutting, and painting. 
Teds Woodworking is a big collection of woodworking plans and all of these are well organized and categorized so that you find what you are looking for fast. These woodworking plans include bed plans, table and chair plans, furniture plans, shed plans, bird house plans and many more. Each of these woodworking plans come with full comprehensive instructions as well as diagrams. You will be able to see, what it is you want to do. The program also includes 150 training videos, so you can see and learn how things should be done. You will be able to see the complete pieces that you need to build and learn how to fit them together. The diagrams are used by many individuals as they go through each part of the process.

And, although a formal education is helpful, it is not necessary, and most woodworkers receive on-the-job training under the supervision of other more experienced workers.  However, because of the ongoing development and modernizing of woodworking machinery, many employers are requiring applicants to have at least a high school diploma, or a few years training in math (specifically geometry) and computer applications.  Many woodworkers will receive training by enrolling in a community or technical college.  Some may attend a university that offers coursework in furniture manufacturing or wood engineering. Individuals who have earned a degree can often move into management or supervisory positions, or go on to open their own woodworking shop.  Becoming a skilled woodworker can often take years, and knowledge of blueprints and work sequences takes training and practice.
Choose a suitable area to do your woodwork crafting in. You'll need sufficient area to move about in, which includes considering the lengths of wood you'll be working with and the types of tools and even machinery you need to set up. As well as space for you to work within, there will also need to be sufficient space to store the wood, the tools and other related items so that they are easy to find and are kept inside, away from the elements.
This bookcase plan is designed to be large enough to handle all of the books belonging to the voracious reader in your family, virtually indestructible to withstand years of abuse, and easy on the pocket book using inexpensive materials from your local home center. For about $100 you can have a bookcase that would cost $600 – $800 at a retail furniture store.
Dust Collector. A dust collector works at the source of creation. It’s main purpose is to collect the dust right from the place you are cutting the wood. A lot of power tools come with a dust collector extension which allows the dust collector to be attached to them directly. This means a lot less cleaning up for you to do. Dust collectors come in two types, single bag and double bag. Single bag ones are more common.
×