We now have over 58 linear feet of shelving (with space under for shoes) for that wall that barely protrudes 12.25" into the room for a total cost of about $125! We plan to make at least two more units to accommodate the more than 15,000 books we own that are currently on store bought or cobbled shelving and in boxes plus have display space for our many collections Our only problem...we didn't take into account the depth of the shelf itself -- if you've got 10" between holes, you actually only get 9 1/8" of useable height on the shelf (most hardback books are 9.5" tall) = major bummer! We measured (from bottom) 12", 12", 10", 10", 9", 9", 10", 10" with top shelf at 13" from the ceiling.
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.

Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
This bookcase lets you have plenty of storage for your books, without you having to show it openly. With a locking system, light mechanisms and a lot of built in shelves, this design form maybe the most high tech of all the others we have discussed. Many interesting features such as a folding door, leading to another area of the house, which a guest may never know- completely steal the show!
It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
To give you an idea about the different bookshelf plans available,this guide presents you 17 simple but alluring bookcase designs to choose from. The designs are not only in a wide array of sizes and styles but they are also inexpensive to build and will fulfil your home space. So be sure to go through all of them to find the best one for your room.
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
Then, beginning several decades ago, shop classes began to be removed from secondary curriculums. With the decrease in educational funding, and increasing emphasis on standardized testing, schools began to cull electives, institute stricter graduation requirements, and focus more on college prep academics and the subjects necessary for passing state exams. There wasn’t money or time to maintain tools and sawdust-filled workshops, and one by one school districts dropped their shop classes, figuring that students who wished to pursue trade skills could do so later at a vocational college.
Eventually, I got engaged and my whole world started to change as I started planning my wedding. I became obsessed with the fun, creative part of planning a wedding. Once my wedding was over, I missed making things for it and I really felt like something was missing and was drawn to the idea of starting a creative business.  I ended up discovering vintage rental companies and I was immediately drawn to this business concept because you spent time curating and creating a collection of beautiful, one of a kind furniture and décor pieces for brides to rent out. But, what I was most drawn to was this up and coming concept of farm table rentals for weddings (this was back in 2013).
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
And, although a formal education is helpful, it is not necessary, and most woodworkers receive on-the-job training under the supervision of other more experienced workers.  However, because of the ongoing development and modernizing of woodworking machinery, many employers are requiring applicants to have at least a high school diploma, or a few years training in math (specifically geometry) and computer applications.  Many woodworkers will receive training by enrolling in a community or technical college.  Some may attend a university that offers coursework in furniture manufacturing or wood engineering. Individuals who have earned a degree can often move into management or supervisory positions, or go on to open their own woodworking shop.  Becoming a skilled woodworker can often take years, and knowledge of blueprints and work sequences takes training and practice.
Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Robyn Mierzwa is the founder of Makeville Studio, a community workshop established in 2008 that offers classes in woodworking and furniture making in Brooklyn, NY. A self-taught woodworker, Robyn has honed her craft over many years and continues to learn something new on every project. In addition to furniture making, she is passionate about teaching and is grateful for the opportunity to help others tap into their creative selves through craft.
Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!
Another option is the circular saw mated with a metal guide (known as a track saw ). These systems have quickly come into their own and can deliver exceptional results. They are ideal for both ripping and cross cutting sheets of plywood, but can handle solid stock if it is wide enough. These systems can cost as much as a table saw but they are compact and very portable.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
1. The choice of wood: The choice of wood depends largely on the purpose which it is to be used and personal taste. We will recommend the type of wood in most cases, but since there are many wood types that fully satisfy the set quality standards for each piece of furniture, the final selection of wood type will depend on your taste, the accessibility on the market and the price. In the furniture manufacture you can use both hardwood and softwood, but if you want your piece of furniture to last for generations, we recommend a good quality hardwood. The quality of wood is one of the most important things that have to be considered when making furniture. A numerous wood types are being used for the furniture manufacture. Traditionally, the most frequently used is a good quality local hardwood, so – depending on which part of the world you are living in – you can usually found the furniture made out of maple, figured maple, cypress, redwood, walnut, cherry, mahogany, oak, birch (yellow, red, flame birch), beech, alder, aspen, elm, hickory, teak, pine and many other wood types. In the past, when demand for the furniture was not so big as it is today and when the furniture was made to last for generations, only the most hard and durable woods were used. Today, when the furniture is no longer made to last for a hundred years, it is often made out of the less durable woods, which are less expensive, and can endure for a long period with good care and maintenance in modern living conditions. Choose good quality and well dried wood with grain and color characteristics that you like, get to know its treatment characteristics and features and you will fulfill the first condition to own a beautiful piece of furniture.

here's my 6x6 version build with #2 pine. shelves are 1x10 and threaded rod upsized to 5/16" to allow for extra width. center upright spaced at 1/3 side to side. this is very complex structurally - all the commenters who don't believe it should build it to really feel how it works. it is basically like a post-tensioned high rise. i think i'd like to paint the uprights and stain the shelves.
Handwork in woodworking tends to be the line where craftsman and factory worker split. Working by hand enables one to create joinery which most machining cannot. The preciseness of the chisel in removing waste enables for a tight and perfect fit in joinery. Chisels come in every shape and size as well as different materials. The harder the material, the less one would need to sharpen, enabling more time to work. Chisels are used in creating dovetails, mortise and tendons, and much more.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close

A small jointer is better than no jointer, but a small jointer is not a great addition to a shop. A jointer needs table length. I would skip buying a small to medium size jointer. Once again, rely on your hand tools. They can perform as well or better than a machine that costs hundreds more, they require a great deal of room, and they should be run in conjunction with a dust collector. You can flatten boards with a jack plane and straighten edges with a jointer. With a little experience it becomes a quick task.
×