I learned about the trade from my father starting when I was 6 years old. I took woodshop courses in high school, and was granted the Industrial Arts Award my senior year. I also took some college courses in woodshop before I started my own business when I turned 19.My average work day is laying out jobs, cutting parts, designing the different jobs, and assembling the cabinets. I also am teaching my daughter how to build woodworking projects and cabinet parts, as well as helping with our cutting boards.
I generally use biscuits for this (three per joint), and I have never had a joint fail (and a bookcase spending five years in an elementary school is a pretty fair test), but dadoes work great here as well. To assist with accuracy and consistency when using biscuits, mark your biscuit locations on a piece of scrap, and then use the scrap as a guide as you mill biscuit slots in each carcass member. The carcass top is attached so that it is flush with the top of the carcass sides. The carcass bottom is attached so that the top of the panel is 2-1/2″ above the floor (or the bottom of the side panel).
Start by arranging all the parts on your work surface. Justin used a flux brush to spread the glue in the slots, and onto the biscuits after they were installed. Any small brush will work, though. When you have everything assembled, install clamps to hold the sides tight to the shelves while the glue dries. Check by using a framing square or by measuring diagonally from opposite corners to make sure the bookcase is square. Adjust it if needed. Then tighten the clamps. This is a good time to take a break while you let the glue dry for about an hour.
Nearly every woodworking project in one form or another will require you to check some intersection, joint, or board end for squareness, or "square." In some cases, you'll need to confirm that an entire assembly is square. For small projects, you can use a squaring tool, such as a try square, speed square, or framing square. For larger projects, you can check for square by measuring diagonally between opposing corners: The assembly is square when the measurements are equal. You can also use the 3-4-5 method, based on the Pythagorean Theorem: a2 + b2 = c2.
[…] Technically this is not a DIY video; it goes by very fast and there are no narrated instructions. That is because it was put together to promote a finished product available here dfmmc.com. But if you have experience welding, it is not all that hard to follow along and figure out the steps and write them down. I might get lazy and buy one … but I love making things, so I definitely will be giving it a try. Whether you buy one ready-made or weld your own, I hope you love this rack as much as I do. What an awesome discovery! If you love rustic decorating you must check out our 85 Rustic storage projects and 40 Rustic home decorating ideas. […]
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
As Chief Creative Officer and Founding Partner at Brit + Co, Anjelika Temple brings her voracious consumption of all things creative and colorful to DIY projects, geeky gadgetry finds and more. When she's not DIY-ing her heart out, you'll find her throwing dinner parties with friends or adventuring with her husband David, their daughter Anokhi, and their silly dog Turkey.
Clamps. Woodworking clamps are essential when building a project. They hold the components together while assembling them together, gluing them, during measuring, cutting et cetera. Be generous with the number of clamps you purchase because you will always need more than you think, and it gets difficult to assemble the project if you do not have enough clamps.
This is a hard question to really answer. I learn a lot from just being in the shop working. but, at the same time I learn and am exposed to so much more online and in books than I would be in my own shop. I had a hard time answering this question. Though I ended up saying books. Why? Because I learn more traditional hand tool techniques, visually see furniture construction(drawings and sketches), and I am exposed to different types of furniture styles, many older books were written by those who had done the same things for years, so they became very proficient at the styles they constructed in . All of these things combined give me a lot of information to take back into my shop. I could learn all of this from schools and from online content, however I feel I have enough basic techniques under my belt to learn successfully from a book, vs. when I first started when I was a kid. And I can buy several books for the cost of one class. Not to say classes are bad, I just don’t have the money to go galavanting all over taking classes.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ... More + Product Details Close
The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later. So I measured my books before I decided how tall the shelves should be. As a rule, a bookcase with shelves between 7 in. and 14 in. apart accommodates most everything. While books generally fit on 8- to 9-in.-deep shelves, I prefer deeper bookcases, so I ripped the plywood to a width of 11 7/8 in.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
It wasn't until the end of the eighteenth century when the first woodworking machine was patented. Some of the basic principles of the earliest woodworking machine tools are still in use today, but the new machines are faster, more powerful, and easier to use than previous generations. We carry a full range of stationary woodworking machines including table saws, miter saws, band saws, drill presses, mortisers, shapers, planers and more. If you have any questions or need help finding what you need, give us a call or email and we'll assist you in finding the right woodworking machine.
My whole life, I’ve loved to be creative and make things. Once I got older though, creativity and anything art related really got pushed aside for a more serious career path. After graduating from college, I decided to go to grad school, get my MS in accounting, and then I became a CPA (Certified Public Accountant), and started working in accounting for several years.