I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.) So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.
Most models have variable speeds, but the scroll saw is designed to cut precisely not quickly. Feed the wood to the saw flush to the saw table. Scroll saw blades are thin and easily broken, so take care not to bend, twist, or put too much pressure on the blade. Drill holes in the waste stock at the tightest corners to facilitate clean and neat cuts. The depth of the saw throat determines how large a piece of wood can be cut on a given saw; 16 inches is a common and generally useful size.
These types of guitar picks are quite easy to make and are perfect for that special musician or guitar player in someone’s family.While they’re not quite good at being used for playing guitar (wood and metal plus constant friction are bad for both parties), the make a lovely ornament for any player and are a great gift, for Christmas or birthdays, to give to that serenading someone.
Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.
Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
If you would like to follow up on these things to learn how to work wood yourself, you could comb through a Google search for each of the topics listed but, to simplify your education, I recommend picking up a few helpful books to start. The first two are mostly about techniques, and the last one is about how to choose which hand tools to purchase.
I agree with your list. My table (cabinet) saw has a router mount built into the table to the right of the blade and it works great. The table is flat cast iron and I can use the table saw fence. I’ve also built an auxiliary fence with dust collection and more features. The only downside is I can’t use a router lift and have to make depth adjustments under the table. To avoid frequent band saw blade changes, I have two: a big one (17″, 2HP, 12″ thick capacity) for typical work and a 9″ bench-top unit that I keep a narrow blade in. I also build radio control airplanes and the small one works great on small stock.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
Start by building a base out of 1x or 2x lumber. Make its depth 1 1/2 to 2 in. less than the depth of the bookcase itself. Its height must be 1/8 in. taller than the baseboard molding you plan to install to make sure the molding slips in easily. Set the base into position and check for level right to left and front to back. Fasten it to the wall studs using 3-in. drywall screws [ 1 ]. Also drive angled screws through the inside of the base and into the floor.
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
Robyn Mierzwa is the founder of Makeville Studio, a community workshop established in 2008 that offers classes in woodworking and furniture making in Brooklyn, NY. A self-taught woodworker, Robyn has honed her craft over many years and continues to learn something new on every project. In addition to furniture making, she is passionate about teaching and is grateful for the opportunity to help others tap into their creative selves through craft.
oh yeah, and buying a bunch of cap nuts is not so easy unless you order ahead of time. i went to two hardware stores (one family owned and one big box) and they kind of laughed at me when i said i needed 32. so i got regular nuts, tightened them so they were flush with the all thread on the front side, hammered it against the board and tightened the back side while holding the front one in place with a wrench. so, some of them have a little bit of overhang on the back side, but i don't have to worry about gouging skin while walking past it. for my next set, i'll order the cap nuts in bulk from ebay ahead of time...
Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
Using these bookcase plans, I built three of these for my children’s school about five years ago (five years in an elementary school is equivalent to a hundred years in a typical home). They have seen tons of abuse, and have held up beautifully. The school can’t wait to get their hands on more of them to replace the “bargain” bookcases they got from a furniture chain which have needed extensive repairs over the same five year period.
11. Other necessary skills: Each woodworker should have a basic knowledge of metalworking. Although most of the home furniture is made out of wood, in this category you may occasionally find some projects made out of metal, or the wooden furniture projects that have a decorative metal parts or fasteners. In our opinion, the combination of wood and wrought iron makes the most beautiful furniture.
Arguably the industrial arts class that is most missed is wood shop. Learning how to work with wood is not only handy, allowing you to make and fix things around the house, but allows you to satisfyingly connect with a long history of craftsmanship. Woodworking was one of the earliest skills mankind developed; the pre-industrial world was largely made of wood, and for thousands of years, all men had at least a rudimentary understanding of how to shape and manipulate it. Even up until the second half of the last century, tradesmen and professionals alike had the confidence to be able to build wooden shelves, cabinets, or even chairs for their family.
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
Adjustable shelves beat fixed shelves in just about every way. They make storage and display space more versatile, of course. And they’re usually just slabs of plywood nosed with strips of wood or edge banding, so they’re easy to make. And because you can remove them, adjustable shelves simplify staining and finishing. The easiest way to support adjustable shelves is by using shelf standards are ($3 for 6 ft. at home centers). Just screw them into place and you’re done.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.