This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist. 

Start by arranging all the parts on your work surface. Justin used a flux brush to spread the glue in the slots, and onto the biscuits after they were installed. Any small brush will work, though. When you have everything assembled, install clamps to hold the sides tight to the shelves while the glue dries. Check by using a framing square or by measuring diagonally from opposite corners to make sure the bookcase is square. Adjust it if needed. Then tighten the clamps. This is a good time to take a break while you let the glue dry for about an hour.


How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.
I make grape vine baskets and trees and other things but in this area peopl cant pay what they are worth so i have to sell them cheap im not getting anywhere fast they sell as fast as i can make them shops buy them and doubl and tripl prices im about to call it a day its to much work for sombody to make all the money i just dont live in the. Rite area is ther a answer to this im just a getting old country boy
Mike Siemsen literally takes you step by step (in "The Naked Woodworker"), going from "I've got nothing" to a full set of inexpensive used tools, and bringing them back into usable condition, then building your own bench and saw-benches.  All for about $700.  That will set you up with just about everything you'll need to make most furniture  (moulding planes, plough planes, combination planes are ... extra-curricular).    $700 spent on new power tools... doesn't get you nearly as far. 
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.
My parents have the space and Dad has the tools -- a drill press, forstner bits and a long workbench were pretty essential. We decided to use countersunk 2x4s as uprights. This eliminated the need for pricey cap/acorn nuts while still leaving the all-thread ends 'protected' on the outside and allowing us to put it flush against the wall without causing damage.

So what is it about starting a woodworking school? It seems that every time I open a woodworking magazine, there is yet another ad for a new woodworking school - usually run by a furniture maker. They're probably thinking, "It can't be that hard, right? I know how to make furniture, I have some tools and I can keep doing my own furniture. But I can attract students and teach them anything they want to know at the same time?"
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!​
As for schooling, many local school districts, community colleges and woodworking stores offer woodworking classes, but those are a mixed bag. A handful is really good and many are terrible. There’s also a big difference between woodworking for fun and doing it for a living, and most classes are geared towards hobbyists. Out of all the proper woodworking schools with good reputations, I’ve only had personal experience with Marc Adams School of Woodworking. That place I recommend 100%, as the instructors are generally active professionals in their specialized niches, so one can always pick their brains for extra information related to earning a living. The director of the school also does a good job of screening instructors to eliminate the ones that don’t interact well in a classroom setting.
Teds woodworking іѕ trying to prevent ԁο-it-yourselfers from continuing to learn it the hard way bесаυѕе anyone who іѕ not a professional carpenter аnԁ hаѕ tried tο complete a woodworking project hаѕ learned that mistakes саn bе expensive. Thе package includes over 16,000 projects, which аrе аƖƖ conveniently delivered іn a digital format. When selecting a project frοm the database, one саn bеɡіn bу first reviewing the detailed material list аnԁ tool guide fοr that specific project. Ted takes the guesswork out οf having tο estimate wood required tο complete a project bесаυѕе even аѕ a professional carpenter fοr 36 years hе felt frustrated bу the guess work required wіth οthеr blue prints. Mοѕt blue prints οn the market today аrе difficult tο read аnԁ harder tο follow. Sadly, many woodworking reference books contain project plans that wіƖƖ result іn frustrating аnԁ incomplete woodworking projects. Teds Woodworking works bесаυѕе іt simplifies the process аnԁ gives information suitable tο аƖƖ levels οf carpentry experience.
Break down plywood Following the cutting diagram, crosscut plywood along the line marked “first cut”. Take the smaller of the two rip 3/4″ plywood according to diagram and cut list. For safety and easier handling, use a circular saw with a good quality blade (following a straight edge guide for a straight cut) for first cross-cut on plywood. If you are not confident in your circular saw’s ability to cut straight lines with no tear out, leave yourself 1/4″ of extra material (there is enough extra material in a 4′ x 8′ sheet of plywood to do this) and make your final cuts on the table saw.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Steely blue walls and a few intricately placed wood slices will give your bathroom a great rustic look. You will need several wood slices to go all the way around the room and then just place them in geometric patterns or however you want. Thin wood slices will affix to the walls easily with wallpaper glue or you can use a hot glue gun if you prefer.
Use 1x12 pine lumber for a rustic appearance. Nothing looks like pine with its large knots and swirls. And because you're using solid lumber, you can sand the edges smooth for a finished appearance. Add a 1/4-inch fir plywood back for strength and stability. Note that "1x12" is a nominal size. The actual size will be ¾-inch thick and 11 ¼-inches wide. 

Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.

By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
My basic advice is to develop lots of connections with people. Most branches of woodworking are hard to sell without knowing the right people – especially when targeting the luxury furnishings or corporate markets. I started down this path with the idea that I might own my own shop but forgot about that once I’d accepted employment in the field. Since I was satisfied working for others, I didn’t bother making the connections, and now I’m so busy it’s hard to get away from the shop long enough to do so. That’s not the end of the world, as we’re still pulling in plenty of work. It just took longer to get there than it should have. For those considering a self-employed woodworking career, it’s a good idea to meet individuals who associate with the types of people that are likely to become future clients. Word-of-mouth is still a powerful form of marketing even in this age of internet.
There are some who also swear by their bandsaw for ripping lumber. A bandsaw can cut faster and is far safer to use than a tablesaw. I personally still prefer to use a tablesaw for ripping for two reasons. First, the bandsaw table and fence are smaller than a typical tablesaw. I find this makes it harder for me to keep a straight edge. Second is the quality of cut. A bandsaw rip will usually be rougher than a tablesaw rip.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.

I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.


​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.

My whole life, I’ve loved to be creative and make things. Once I got older though, creativity and anything art related really got pushed aside for a more serious career path. After graduating from college, I decided to go to grad school, get my MS in accounting, and then I became a CPA (Certified Public Accountant), and started working in accounting for several years.


There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
My basic advice is to develop lots of connections with people. Most branches of woodworking are hard to sell without knowing the right people – especially when targeting the luxury furnishings or corporate markets. I started down this path with the idea that I might own my own shop but forgot about that once I’d accepted employment in the field. Since I was satisfied working for others, I didn’t bother making the connections, and now I’m so busy it’s hard to get away from the shop long enough to do so. That’s not the end of the world, as we’re still pulling in plenty of work. It just took longer to get there than it should have. For those considering a self-employed woodworking career, it’s a good idea to meet individuals who associate with the types of people that are likely to become future clients. Word-of-mouth is still a powerful form of marketing even in this age of internet.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
Break down plywood Following the cutting diagram, crosscut plywood along the line marked “first cut”. Take the smaller of the two rip 3/4″ plywood according to diagram and cut list. For safety and easier handling, use a circular saw with a good quality blade (following a straight edge guide for a straight cut) for first cross-cut on plywood. If you are not confident in your circular saw’s ability to cut straight lines with no tear out, leave yourself 1/4″ of extra material (there is enough extra material in a 4′ x 8′ sheet of plywood to do this) and make your final cuts on the table saw.
The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Storage can never be enough for a home with children. Especially if the family is midsized to a large one! A headboard with optimum storage space is an ideal solution in children’s room to accommodate most of their belongings, so that they can have an easy access to them on a daily basis, and not litter them everywhere. The headboard can be revamped for them, according to their choice of colors and need.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
Hey there! My name is Emma Clark, a part-time interior designer and full-time mom of one pretty little lady. This blog is the fruit of my extensive experiences as an interior designer and home improvement enthusiast. More so, I'm here to share with you a lot of great ideas on what YOU can do to make your home into a masterpiece: all cost-effective and amazingly creative.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
But what if you want to make a box? The revered (and overly-mystified) dovetail joint is a very strong way to join corners of boards. Of all features that non-woodworkers admire today, the dovetail joint is the one that creates the most awe. It is composed of one side cut into wedge-shaped “tails” that mate into corresponding “pins.” When fitted together, the wedge shape prevents the boards from sliding apart in one direction. This joint has been very standard construction since the 1700s. Never meant to impress, it was usually intentionally hidden behind veneer, molding, or paint so that no one would have to look at that “ugly” joinery. It wasn’t until the arts and crafts movement that visible joinery was considered an aesthetic asset. Today, making dovetail joints has become a litmus test for serious woodworkers, but don’t let this scare you away from trying it. Check out a few of the four million “How to Cut Dovetails” videos online and then get into the shop. It’s much more straightforward than people think: Cut tails. Trace the tails on the other board. Then cut out the waste you traced. That’s pretty much it. All the fine tuning is just practice.
Description: You've seen him demo in the store, now come join Rod Hendrickson to learn to carve your own realistic animals. Beginners and carvers of all levels are welcome to join this on-going class. First time students will make a miniature duck decoy. Tuition is for 12 hours of class time. Rough cut outs are supplied by the instructor - check with Rod for cost. (approximately $15 for the miniature duck decoy blank)

I was attracted to this page by the headboard. It looks great and it’s unique. I must disagree with the first sentence, that rustic is ‘in’ right now. I’m thinking, ‘It’s the great recession’. Any money I spend better get me the most refined thing I can afford. Kind of like how I believe that new store bought jeans with holes in them are going out of style like a cold cup of coffee.
×