The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
!function(n,t){function r(e,n){return Object.prototype.hasOwnProperty.call(e,n)}function i(e){return void 0===e}if(n){var o={},s=n.TraceKit,a=[].slice,u="?";o.noConflict=function(){return n.TraceKit=s,o},o.wrap=function(e){function n(){try{return e.apply(this,arguments)}catch(e){throw o.report(e),e}}return n},o.report=function(){function e(e){u(),h.push(e)}function t(e){for(var n=h.length-1;n>=0;--n)h[n]===e&&h.splice(n,1)}function i(e,n){var t=null;if(!n||o.collectWindowErrors){for(var i in h)if(r(h,i))try{h[i].apply(null,[e].concat(a.call(arguments,2)))}catch(e){t=e}if(t)throw t}}function s(e,n,t,r,s){var a=null;if(w)o.computeStackTrace.augmentStackTraceWithInitialElement(w,n,t,e),l();else if(s)a=o.computeStackTrace(s),i(a,!0);else{var u={url:n,line:t,column:r};u.func=o.computeStackTrace.guessFunctionName(u.url,u.line),u.context=o.computeStackTrace.gatherContext(u.url,u.line),a={mode:"onerror",message:e,stack:[u]},i(a,!0)}return!!f&&f.apply(this,arguments)}function u(){!0!==d&&(f=n.onerror,n.onerror=s,d=!0)}function l(){var e=w,n=p;p=null,w=null,m=null,i.apply(null,[e,!1].concat(n))}function c(e){if(w){if(m===e)return;l()}var t=o.computeStackTrace(e);throw w=t,m=e,p=a.call(arguments,1),n.setTimeout(function(){m===e&&l()},t.incomplete?2e3:0),e}var f,d,h=[],p=null,m=null,w=null;return c.subscribe=e,c.unsubscribe=t,c}(),o.computeStackTrace=function(){function e(e){if(!o.remoteFetching)return"";try{var t=function(){try{return new n.XMLHttpRequest}catch(e){return new n.ActiveXObject("Microsoft.XMLHTTP")}},r=t();return r.open("GET",e,!1),r.send(""),r.responseText}catch(e){return""}}function t(t){if("string"!=typeof t)return[];if(!r(j,t)){var i="",o="";try{o=n.document.domain}catch(e){}var s=/(.*)\:\/\/([^:\/]+)([:\d]*)\/{0,1}([\s\S]*)/.exec(t);s&&s[2]===o&&(i=e(t)),j[t]=i?i.split("\n"):[]}return j[t]}function s(e,n){var r,o=/function ([^(]*)\(([^)]*)\)/,s=/['"]?([0-9A-Za-z$_]+)['"]?\s*[:=]\s*(function|eval|new Function)/,a="",l=10,c=t(e);if(!c.length)return u;for(var f=0;f0?s:null}function l(e){return e.replace(/[\-\[\]{}()*+?.,\\\^$|#]/g,"\\$&")}function c(e){return l(e).replace("<","(?:<|<)").replace(">","(?:>|>)").replace("&","(?:&|&)").replace('"','(?:"|")').replace(/\s+/g,"\\s+")}function f(e,n){for(var r,i,o=0,s=n.length;or&&(i=s.exec(o[r]))?i.index:null}function h(e){if(!i(n&&n.document)){for(var t,r,o,s,a=[n.location.href],u=n.document.getElementsByTagName("script"),d=""+e,h=/^function(?:\s+([\w$]+))?\s*\(([\w\s,]*)\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,p=/^function on([\w$]+)\s*\(event\)\s*\{\s*(\S[\s\S]*\S)\s*\}\s*$/,m=0;m]+)>|([^\)]+))\((.*)\))? in (.*):\s*$/i,o=n.split("\n"),u=[],l=0;l=0&&(g.line=v+x.substring(0,j).split("\n").length)}}}else if(o=d.exec(i[y])){var _=n.location.href.replace(/#.*$/,""),T=new RegExp(c(i[y+1])),E=f(T,[_]);g={url:_,func:"",args:[],line:E?E.line:o[1],column:null}}if(g){g.func||(g.func=s(g.url,g.line));var k=a(g.url,g.line),A=k?k[Math.floor(k.length/2)]:null;k&&A.replace(/^\s*/,"")===i[y+1].replace(/^\s*/,"")?g.context=k:g.context=[i[y+1]],h.push(g)}}return h.length?{mode:"multiline",name:e.name,message:i[0],stack:h}:null}function y(e,n,t,r){var i={url:n,line:t};if(i.url&&i.line){e.incomplete=!1,i.func||(i.func=s(i.url,i.line)),i.context||(i.context=a(i.url,i.line));var o=/ '([^']+)' /.exec(r);if(o&&(i.column=d(o[1],i.url,i.line)),e.stack.length>0&&e.stack[0].url===i.url){if(e.stack[0].line===i.line)return!1;if(!e.stack[0].line&&e.stack[0].func===i.func)return e.stack[0].line=i.line,e.stack[0].context=i.context,!1}return e.stack.unshift(i),e.partial=!0,!0}return e.incomplete=!0,!1}function g(e,n){for(var t,r,i,a=/function\s+([_$a-zA-Z\xA0-\uFFFF][_$a-zA-Z0-9\xA0-\uFFFF]*)?\s*\(/i,l=[],c={},f=!1,p=g.caller;p&&!f;p=p.caller)if(p!==v&&p!==o.report){if(r={url:null,func:u,args:[],line:null,column:null},p.name?r.func=p.name:(t=a.exec(p.toString()))&&(r.func=t[1]),"undefined"==typeof r.func)try{r.func=t.input.substring(0,t.input.indexOf("{"))}catch(e){}if(i=h(p)){r.url=i.url,r.line=i.line,r.func===u&&(r.func=s(r.url,r.line));var m=/ '([^']+)' /.exec(e.message||e.description);m&&(r.column=d(m[1],i.url,i.line))}c[""+p]?f=!0:c[""+p]=!0,l.push(r)}n&&l.splice(0,n);var w={mode:"callers",name:e.name,message:e.message,stack:l};return y(w,e.sourceURL||e.fileName,e.line||e.lineNumber,e.message||e.description),w}function v(e,n){var t=null;n=null==n?0:+n;try{if(t=m(e))return t}catch(e){if(x)throw e}try{if(t=p(e))return t}catch(e){if(x)throw e}try{if(t=w(e))return t}catch(e){if(x)throw e}try{if(t=g(e,n+1))return t}catch(e){if(x)throw e}return{mode:"failed"}}function b(e){e=1+(null==e?0:+e);try{throw new Error}catch(n){return v(n,e+1)}}var x=!1,j={};return v.augmentStackTraceWithInitialElement=y,v.guessFunctionName=s,v.gatherContext=a,v.ofCaller=b,v.getSource=t,v}(),o.extendToAsynchronousCallbacks=function(){var e=function(e){var t=n[e];n[e]=function(){var e=a.call(arguments),n=e[0];return"function"==typeof n&&(e[0]=o.wrap(n)),t.apply?t.apply(this,e):t(e[0],e[1])}};e("setTimeout"),e("setInterval")},o.remoteFetching||(o.remoteFetching=!0),o.collectWindowErrors||(o.collectWindowErrors=!0),(!o.linesOfContext||o.linesOfContext<1)&&(o.linesOfContext=11),void 0!==e&&e.exports&&n.module!==e?e.exports=o:"function"==typeof define&&define.amd?define("TraceKit",[],o):n.TraceKit=o}}("undefined"!=typeof window?window:global)},"./webpack-loaders/expose-loader/index.js?require!./shared/require-global.js":function(e,n,t){(function(n){e.exports=n.require=t("./shared/require-global.js")}).call(n,t("../../../lib/node_modules/webpack/buildin/global.js"))}});
How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.

In order to be successful in woodworking, there are skills absolutely necessary to know and master.  Many of these skills were once taught in high school’s all across the nation, but today, most woodshop classes have been suspended, and people must learn through college classes, apprenticeships, internships, from professionals, or by trial and error. 
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
There may or may not be an easy answer to this. If you already have a woodworking craft you are passionate about, then that's great. All you need to do is a little market research to figure out whether others love it as much as you do. You do not have to go very far and wide to do some primary market research. Start with your family and friends who will give you a fair and honest opinion.

I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.


There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
I was self taught meaning I gleaned anything and everything I could from books,DVD’s,TV shows like Norm,Roy Underhill and any where else I could pick up information.Even though I had more than 20 years of woodworking I have in the last few years I’ve found a mentor in Charles Neil and now subscribe to his on line Mastering woodworking show. As to taking a class I’m a bit prejudice since I teach a community collage class on woodworking I highly recommend that you take any classes you can afford.

Click HERE or on the image below for the downloadable Double Chair Bench Plans. These plans are 100% free and you have the option to donate at the time of download to help support DIY PETE so he can devote more time in creating FREE video tutorials and plans for you. This is 100% optional of course! If you’d like them for FREE simply enter “0” in the dollar amount   Cheers! – Pete
Make It: Paint nine craft sticks red, six craft sticks white, and four mini craft sticks white. Let them dry. On a rectangle piece of cardstock, have your child create a blue sky and green grass with colored paper or markers. Then help her create the bottom of the barn by gluing on a row of 11 craft sticks vertically in the following pattern: two red, one white, five red, one white, two red. Glue white sticks horizontally along the top and bottom and cross two in the middle as shown. Glue the mini craft sticks to red cardstock to form the barn roof. Adhere the barn roof to the background above the barn. Cut out a rectangle from black paper and adhere it to the barn. Cut strips from a paper bag and crumple for the look of hay; adhere to black rectangle.
Small planers on the other hand can do a lot for you. Here it is hard to argue with their capabilities. A large industrial-weight planer is a machine few small shops can justify, but there are numerous portable planers available for a few hundred dollars that can deliver a reasonable cut. They allow you to quickly clean up glue joints or prepare rough lumber.
We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.
All things considered, the easiest and most practical way to plane a piece of unmilled wood is to use a router. You can pick up a halfway decent router fairly inexpensively, and the good thing about investing in one is that there’s truly no limit to what you can do with it - planing a piece of wood is just one of a million different things a router can be used for.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.

Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.


The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later. So I measured my books before I decided how tall the shelves should be. As a rule, a bookcase with shelves between 7 in. and 14 in. apart accommodates most everything. While books generally fit on 8- to 9-in.-deep shelves, I prefer deeper bookcases, so I ripped the plywood to a width of 11 7/8 in.

WoodSkills and Norman Pirollo offer online woodworking classes, woodworking plans, video lectures and woodworking tutorials. The classes and courses provide detailed and comprehensive step by step sequences for woodworking skill-building. Each woodworking class and tutorial is based on actual furniture making expertise. As founder of  White Mountain Design , Refined Edge Design , WoodSkills and Pirollo Design, I bring to you two decades of knowledge in furniture making. In recent years, I have authored three woodworking books:
Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.
Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.

Add curves and other fancy touches to your bookcase the easy way with polyurethane plastic trim. Working with polyurethane trim is much like working with wood—you cut it with standard saw blades, nail it by hand or with a gun and paint it just like wood. Home centers carry a small selection of polyurethane trim. You can find an endless variety of options by going online and searching for “polyurethane trim” (some products are listed as “urethane” rather than “polyurethane”).


It could be a pun about family life, or a comment on whatever pets have currently made their territory. People love these simple decorations right next to their front doors.With just a board, a little creative painting, and some simple small hooks, you can find yourself around $15 per holder, all for around 30 minutes of sanding, cutting, and painting. 
Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).

We recruited Justin and his son to help us with this story. Justin is a full-time firefighter and a woodworker on his off days. His 11-year-old son Jackson, an up-and-coming woodworker, had fun with his dad and learned a few power tool techniques in the process. We provided the plans and gave a few pointers along the way, and Justin and Jackson took it from there.
[…] Technically this is not a DIY video; it goes by very fast and there are no narrated instructions. That is because it was put together to promote a finished product available here dfmmc.com. But if you have experience welding, it is not all that hard to follow along and figure out the steps and write them down. I might get lazy and buy one … but I love making things, so I definitely will be giving it a try. Whether you buy one ready-made or weld your own, I hope you love this rack as much as I do. What an awesome discovery! If you love rustic decorating you must check out our 85 Rustic storage projects and 40 Rustic home decorating ideas. […]
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
Rip the 3/4-in. plywood to width for the case sides and shelves using a table saw or circular saw and straightedge guide. Crosscut the case sides to length, making them 2 in. shorter than the distance from the top of the base to the ceiling. Then, cut all the shelves to length. The shelves should be no longer than 36 in. to keep them from sagging under heavy loads. Before proceeding, finish all the plywood pieces.
There are some who also swear by their bandsaw for ripping lumber. A bandsaw can cut faster and is far safer to use than a tablesaw. I personally still prefer to use a tablesaw for ripping for two reasons. First, the bandsaw table and fence are smaller than a typical tablesaw. I find this makes it harder for me to keep a straight edge. Second is the quality of cut. A bandsaw rip will usually be rougher than a tablesaw rip.
Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
Hi, Patrick. In a space constrained scenario, a good track saw can enable you to do some very high quality work, and you can perform many of the tasks that are commonly performed on a table saw. You could definitely build closets, vanities, and a great variety of other comparable projects with a good track saw. The advantages that a table saw can bring are efficiency, repeatability with a single fence setup, and support for a dado blade. If you get a larger shop space someday and decide to add a table saw, you’ll still get plenty of use out of your track saw. Even though I have a large cabinet saw I still use a circular saw and guide for a lot of cuts on sheet goods, mainly because a 4×8 sheet can be unwieldy to handle on a table saw.
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.

Learn the basics of woodworking with simple hands-on projects to build your confidence and skills. Each lesson in this class explores an area of woodworking that will form the building blocks of all future woodworking projects you undertake. Keeping the average DIY'er in mind, this entire class is conducted using basic handheld power tools, with no fancy fixed tools like table saws, lathes, planers, or drill presses.


Start with the horizontal base rail at the bottom of the bookcase. Hold the rail against the bottom shelf and mark onto the rail the center of each slot cut into the shelf. Then use the biscuit joiner to cut corresponding slots into the back of the base rail. Apply carpenter's glue to the front edge of the bottom shelf, and the rear of the base rail. Insert No. 20 biscuits into the shelf slots, then press the rail into place [ 7 ]. Use a rubber mallet to tap the rail tight. Wipe away any excess glue with a cloth. Attach the valance that runs across the top of the bookcase the same way. (Note: Its bottom edge aligns flush with the case top.)
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.
Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!

Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
×