Make It: Paint four clothespins black. Thread a 4-inch-long black chenille stems through the two holes of a large black button. Twist and curl the ends of chenille stems where they meet to form antennae. Glue googly eyes just below the antennae. Next, cut three 3-inch pieces of black stems for each ant. Have your child help you thread all three though the spring hole in each clothespin and adjust to form the legs. Glue the face and two more black buttons to the top of each clothespin. Then use the clips to secure your tablecloth, and enjoy a carefree meal in the summer sun.
Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.
There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period. Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
With your tools set up and ready to go, you’re ready to get started on woodworking projects. If you’re looking for beginner woodworking projects, we’ve got you covered. Projects range from birdhouses to jewelry boxes; there’s something for everyone. You’re sure to find a project that’s a good fit for your skills and tools, and that you’ll enjoy creating.
Once you’ve mastered the basics, then check out magazines like Fine Woodworking, Woodcraft, etc. Visit your local woodworking store (like Woodcraft or Rockler) and browse the book / plans section. What I like is these stores normally have people with woodworking expertise and can answer most of your questions whether they be basic or advanced. They also offer monthly workshops at an affordable price.
Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps. 

Whether starting a workshop from scratch or enhancing an existing one, few woodworkers will come up with the same workshop tools wish lists. Most often the first priority is either a table saw, band saw, or radial arm saw, followed by equipment to dress up lumber, such as a planer, lathe, and drill press. From there on, the equipment you’ll want will depend to a large degree on the projects you end up building most often.
Jim, I belong to Charles Neil’s website and get his DVDs and watch his videos. He’s a great teacher. However, if I had to travel all the way up to Virginia I’d be out of luck. The Internet is a great asset for woodworkers. BTW, I wish the college you teach in was right here in my town. If it were I’d enroll because I know that you are a fine woodworker. Traveling somewhere to a class is an expense that I couldn’t afford in money and time.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Another fine example of remodelling furniture and re-using what already exists in the house.  The bookcase involves using your old kitchen cabinets, and building new shelves on top of them. The final product can also be used as an entertainment unit, housing a television, books and things of your interest along with ample storage to keep other utility objects.
×