Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.

Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
Rip the 3/4-in. plywood to width for the case sides and shelves using a table saw or circular saw and straightedge guide. Crosscut the case sides to length, making them 2 in. shorter than the distance from the top of the base to the ceiling. Then, cut all the shelves to length. The shelves should be no longer than 36 in. to keep them from sagging under heavy loads. Before proceeding, finish all the plywood pieces.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
It's a little strange but you can charge premium prices for birdhouses and people are ready to pay for it. People who want to enjoy birds coming to the garden, attach a high value to a functional and nice looking bird-house. And who doesn't really want pretty birds coming and chirping in their gardens. Therefore, birdhouse is one of the top-selling woodworking projects.
Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
If you have an old guitar lying in your house that you just don’t want to let go of, due to an emotional attachment, here is a great way of re-using it, by converting it into a bookcase. Whether you hang it in your living room or in your courtyard, it looks really attractive, housing your favourite reads. If one can arrange for a hammock, the entire setting of your courtyard will look splendid!
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
In my opinion, there are two kinds of woodworking. One is fine woodworking which is well worth learning and mastering. It just takes more time, skills and know-how. Second, there is basic or “maker” woodworking which is probably where you want to start. Find something that will help you jump in and gain some confidence with some basic tools and projects. Then, if you want, graduate to fine woodworking.
thank you, thank you, thank you!! the lumber that i had in the garage wasn't exactly what your plans called for (2x4s and 1x10s), so i adjusted the length of the all thread to accommodate the depth. also, one of my 2x4s was kind of wonky and i was worried it would jeopardize the stability of the set - but it's totally solid! the shelves are level and aren't going anywhere!! :) (i threw all of my body weight against it, and it's totally solid!) it's approx. 4' wide by 7.5' tall.

This is the most fundamental joint in all wood construction. Whenever we have to join a horizontal member (like a chair rail) to a vertical member (like a leg), we need to interlock these pieces at a right angle. By fitting a tenon into a corresponding mortise (hole), we can create a solid 90° joint. Although it may look intuitive to make, achieving a nice, tight fit requires careful technique and practice. There are many ways to make a mortise, but I use a stout chisel designed for that task and simply determine the width of the tenon based on that chisel’s dimension. Cutting the tenon is usually a matter of four straight saw cuts. When you do learn how to lay this joint out properly and cut it to a snug fit, the world of woodworking opens up to you. At that point, you know all the joinery required to build most tables and chairs.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Once you’ve mastered the basics, then check out magazines like Fine Woodworking, Woodcraft, etc. Visit your local woodworking store (like Woodcraft or Rockler) and browse the book / plans section. What I like is these stores normally have people with woodworking expertise and can answer most of your questions whether they be basic or advanced. They also offer monthly workshops at an affordable price.

While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
In order to be successful in woodworking, there are skills absolutely necessary to know and master.  Many of these skills were once taught in high school’s all across the nation, but today, most woodshop classes have been suspended, and people must learn through college classes, apprenticeships, internships, from professionals, or by trial and error. 
If you are wanting to build great looking chairs for your patio you've come to the right place. I bought a home late last year and didn't have any patio furniture whatsoever. My dad had built a beautiful piece for their home and so I credit him with design help and the inspiration to build my own. This setup is perfect for enjoying a relaxing evening out on the deck with friends or family. I built my chairs out of cedar because cedar does not rot and stands up against the outdoor elements quite well. You can use pine as long as it is painted or coated with a thick finish of poly.
6. Furniture construction: The shape of the piece of furniture will generally determine its construction. Furniture construction is no less an important factor in the ultimate beauty of a piece of furniture than is its design. The best-designed article may be ruined by poor construction. When making our furniture plans we tend to include a variety of woodworking joints and various types of constructions. Of course, if you are not experienced in making those kinds woodworking joints or you do not have necessary tools and machinery for their manufacture, you can analyze the construction and customize it to your needs and abilities.
Thickness planer. A thickness planer is used to fix surfaces of imperfect wood. If you are picking up less than perfect wood from the lumberyard, wood with some surface defects, a planer will let you fix that wood in the quickest time. A thickness planer pays for itself quick as it allows you to buy cheaper wood that doesn’t have perfect surfaces and fix it yourself. Be careful though. You loose wood during planing. So the remaining amount of wood still has to be worth the price you paid for it.
×