Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.
The best advice I could give you is to learn WordPress or find a friend who can help you figure it out. Once the light bulb goes off there will be no stopping you, you will have the power in your own hands to provide what your end user needs and to educate them about the benefits and your products value – in a selfish, wasteful, throw-away society who expect everything delivered yesterday and expect to pay dirt cheap prices for your skills and repetitive hard work. End of rant….Sorry but I just had to comment. I know what it’s like, don’t lose hope!
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Learn woodworking from a home computer, tablet, or smartphone. Woodworking video lectures can be followed sequentially or in any order. The lectures can be repeated to reinforce what you have learned. Flexibility in learning allows you to speed your woodworking knowledge. Learning the essentials of woodworking accelerate your learning curve to become a woodworker
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
In being self-employed, one day will greatly vary from the next, but generally, I start in the morning by dealing with in-town errands or head right to the shop if there are none. Once at the shop, there’s an e-mail check, then a brief glance at various websites to look for new developments related to our market and clientele. Then the real workday starts. I’ve got a bunch of notes regarding current projects taped next to my computer and will make a list for the day’s tasks by picking the highest priority items from the notes. The goal is to get that stuff accomplished by the end of the day. There are two of us in the shop, but we usually work on separate projects, so that’s why I have my own to-do list. Some days are spent on the computer designing or creating programs for the laser or CNC. Other times we’re doing runs of sunglasses or guitar parts which we sell wholesale to other businesses. In which case, I may be operating the laser or CNC. Despite the high-tech tooling, there’s still a lot of bench work to do, and that can involve cutting and fitting joints with chisels and hand planes. Besides that, there’s always plenty of rough lumber to mill since no project can begin until boards are flattened, surfaced and cut to dimension.
Make It: Paint nine craft sticks red, six craft sticks white, and four mini craft sticks white. Let them dry. On a rectangle piece of cardstock, have your child create a blue sky and green grass with colored paper or markers. Then help her create the bottom of the barn by gluing on a row of 11 craft sticks vertically in the following pattern: two red, one white, five red, one white, two red. Glue white sticks horizontally along the top and bottom and cross two in the middle as shown. Glue the mini craft sticks to red cardstock to form the barn roof. Adhere the barn roof to the background above the barn. Cut out a rectangle from black paper and adhere it to the barn. Cut strips from a paper bag and crumple for the look of hay; adhere to black rectangle.
5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
10.  While manufacturing the furniture, another important thing besides the precise parts manufacture is the assemblage. The pieces, when fitted, should come together easily, and not require to be twisted, sprung or bent in order to put the piece article together. It is the practice with skilled cabinet maker to put a piece of furniture completely together once (without glue, screws or nails)to see that everything fits right, before putting together permanently. After fitting the parts of a piece of furniture and before gluing, smooth such parts as cannot readily be smoothed after putting together permanently.
Arguably the industrial arts class that is most missed is wood shop. Learning how to work with wood is not only handy, allowing you to make and fix things around the house, but allows you to satisfyingly connect with a long history of craftsmanship. Woodworking was one of the earliest skills mankind developed; the pre-industrial world was largely made of wood, and for thousands of years, all men had at least a rudimentary understanding of how to shape and manipulate it. Even up until the second half of the last century, tradesmen and professionals alike had the confidence to be able to build wooden shelves, cabinets, or even chairs for their family.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.

Thickness planer. A thickness planer is used to fix surfaces of imperfect wood. If you are picking up less than perfect wood from the lumberyard, wood with some surface defects, a planer will let you fix that wood in the quickest time. A thickness planer pays for itself quick as it allows you to buy cheaper wood that doesn’t have perfect surfaces and fix it yourself. Be careful though. You loose wood during planing. So the remaining amount of wood still has to be worth the price you paid for it.


Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
gregoryterry06111969@gmail.com Thanks for the pep talk. I’ve been kinda stale on my creative thinking lately. A few years back i made a birdhouse for a gal friend of mine,except the birdhouse wasn’t for birds it was to hide or disguise a security camera for her small motel she owns. She loved it and i enjoyed making it although i spent too much time with intricate details. My first attempt on the first piece i cut was unsatisfactory to me so i discarded that piece and continued with the project. After it was completed and she loved it so much she paid me 125$ for it. Well longer story shortened I get bored easily and one day sometime later I was looking at that first piece I had discarded and it inspired me to create something i call the ” Perpetual Puzzle”. Turns out everybody I’ve shown it to absolutely loves it and say that they would definitely pay good money for one. My problem is I don’t know the first thing about marketing or patents, copyrights and so forth. Any advise would be greatly appreciated.

Looking for easy bookshelf plans? Well, worry no more. You are come to the right place. Any book or website maybe tell you that finding innovative ways to display and store books can be just as charming of the arts. And although you are the person who love for reading a lot of books and need to high budget to buy a bookshelf for storing and displaying the books. Designing and building your own bookcase is an easy project and you can easily build it to store your book, this way will save your a lot budget.


To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.

Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
If you have an old guitar lying in your house that you just don’t want to let go of, due to an emotional attachment, here is a great way of re-using it, by converting it into a bookcase. Whether you hang it in your living room or in your courtyard, it looks really attractive, housing your favourite reads. If one can arrange for a hammock, the entire setting of your courtyard will look splendid!

Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.
Click HERE or on the image below for the downloadable Double Chair Bench Plans. These plans are 100% free and you have the option to donate at the time of download to help support DIY PETE so he can devote more time in creating FREE video tutorials and plans for you. This is 100% optional of course! If you’d like them for FREE simply enter “0” in the dollar amount   Cheers! – Pete 

The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later. So I measured my books before I decided how tall the shelves should be. As a rule, a bookcase with shelves between 7 in. and 14 in. apart accommodates most everything. While books generally fit on 8- to 9-in.-deep shelves, I prefer deeper bookcases, so I ripped the plywood to a width of 11 7/8 in.
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.

You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
But what if you want to make a box? The revered (and overly-mystified) dovetail joint is a very strong way to join corners of boards. Of all features that non-woodworkers admire today, the dovetail joint is the one that creates the most awe. It is composed of one side cut into wedge-shaped “tails” that mate into corresponding “pins.” When fitted together, the wedge shape prevents the boards from sliding apart in one direction. This joint has been very standard construction since the 1700s. Never meant to impress, it was usually intentionally hidden behind veneer, molding, or paint so that no one would have to look at that “ugly” joinery. It wasn’t until the arts and crafts movement that visible joinery was considered an aesthetic asset. Today, making dovetail joints has become a litmus test for serious woodworkers, but don’t let this scare you away from trying it. Check out a few of the four million “How to Cut Dovetails” videos online and then get into the shop. It’s much more straightforward than people think: Cut tails. Trace the tails on the other board. Then cut out the waste you traced. That’s pretty much it. All the fine tuning is just practice.
It's a little strange but you can charge premium prices for birdhouses and people are ready to pay for it. People who want to enjoy birds coming to the garden, attach a high value to a functional and nice looking bird-house. And who doesn't really want pretty birds coming and chirping in their gardens. Therefore, birdhouse is one of the top-selling woodworking projects.
Before you put any tool to your lumber, you will need to understand its proper orientation and what direction to plane the board. As trees grow, growth ring layers continue to build on one another and this produces beautiful grain that shows in our boards. This grain can make planing it trickier if we ignore the ideal direction to work. Working wood grain is kind of like petting a cat — if you go from tail to head, you will find the hair standing straight up and might get a hissing disapproval, but if you pet “with the grain” from head to tail, you’ll find the hairs lay down nice and smooth and purring will ensue.

I decided to start my own vintage rental company, with farm tables being the main rental item. There was just one problem, I couldn’t afford to buy twenty farm tables… Which led me to my only option, I’d have to build them, except that again I didn’t know a thing about building or power tools nor did I know anyone that I felt comfortable asking to teach me. But, I figured if I could pass the CPA exam, I could figure out how to build a table on my own and learn how to use power tools.


An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
Learn woodworking from a home computer, tablet, or smartphone. Woodworking video lectures can be followed sequentially or in any order. The lectures can be repeated to reinforce what you have learned. Flexibility in learning allows you to speed your woodworking knowledge. Learning the essentials of woodworking accelerate your learning curve to become a woodworker
With a lot of woodworking tools, the basic technique is pretty self-explanatory. But not all of them are so intuitive. Proper use of hand planes requires a bit of instruction and practice to develop the feel of adjusting the cut from coarse to fine. Additionally, the edge can be askew or the cap iron can be in the wrong place. Although these things require a little bit of research to figure out, properly using a hand plane is an undeniably attainable skill. I encourage you to grab an old plane and hop on YouTube to search “tune up an old hand plane” or “how to use a hand plane.” There will be more than enough hours of video to make up for what you missed in shop class.

As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.
With sharp hand tools and unforgiving power tools, woodworking can be a dangerous activity. By following some basic safety rules, though, you can considerably reduce the risk of injury. In order to be effective, safety rules must be implemented every time—no exceptions. Committing to making safety a habit increases your enjoyment and lowers the chance of injury (or worse) while woodworking.
Kids love to watch grown-ups use woodworking tools, but what they love even more is making the sawdust fly themselves. With minimal equipment and adult help, your child will soon be turning out a wonderful variety of toys, games, gifts, household objects, and holiday decorations. These 50 easy and inexpensive projects are arranged by age and skill level.

In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
As far as shelves go, they’re not too efficient at holding much (six pieces of wood with the only piece used for storage), but they look quite pretty and are quite easy to make. You can usually charge double for these shelves compared to the traditional floating shelves, and with a little customizable paint option, you can dominate the contemporary scene with these neat looking shelves.

The old saying "If only I knew then what I know now" certainly applies to buying woodworking tools . Like nearly every woodworker, I would love a large shop equipped with all the best tools. Like most woodworkers however, I have had to make choices due to finances, space, and what was available at the time of need. As I look back at the purchases I made over the last 30 years, I have few true regrets, but there are many things I would do differently. Here is how I would approach equipment selection today.
×