Now install the vertical stiles. Hold each stile against the front edge of the bookcase sides, then transfer the biscuit­slot locations from the sides onto the stile. Cut slots using the biscuit joiner, apply glue to both surfaces, insert biscuits into the slots and press the stile home. Use a rubber mallet to tap it tight. Repeat the glue-and-­biscuit routine to attach the horizontal mahogany aprons to the shelves. Prior to installation, I routed a decorative profile along the bottom edge of each apron to create shadow lines that accentuate the shelves. The aprons are more than decorative, though. They stiffen the shelf to prevent sagging. Trim the top of the bookcase with crown molding [ 8 ] and the bottom with base molding [ 9 ]. Wait 8 to 10 hours for the glue to cure before filling the shelves.


Using these bookcase plans, I built three of these for my children’s school about five years ago (five years in an elementary school is equivalent to a hundred years in a typical home). They have seen tons of abuse, and have held up beautifully. The school can’t wait to get their hands on more of them to replace the “bargain” bookcases they got from a furniture chain which have needed extensive repairs over the same five year period.
These types of guitar picks are quite easy to make and are perfect for that special musician or guitar player in someone’s family.While they’re not quite good at being used for playing guitar (wood and metal plus constant friction are bad for both parties), the make a lovely ornament for any player and are a great gift, for Christmas or birthdays, to give to that serenading someone.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
Steely blue walls and a few intricately placed wood slices will give your bathroom a great rustic look. You will need several wood slices to go all the way around the room and then just place them in geometric patterns or however you want. Thin wood slices will affix to the walls easily with wallpaper glue or you can use a hot glue gun if you prefer.

My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
I generally use biscuits for this (three per joint), and I have never had a joint fail (and a bookcase spending five years in an elementary school is a pretty fair test), but dadoes work great here as well. To assist with accuracy and consistency when using biscuits, mark your biscuit locations on a piece of scrap, and then use the scrap as a guide as you mill biscuit slots in each carcass member. The carcass top is attached so that it is flush with the top of the carcass sides. The carcass bottom is attached so that the top of the panel is 2-1/2″ above the floor (or the bottom of the side panel).
Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
The knotty pine bookcase parts are all standard dimensional lumber that you can find at any home center. We joined the shelves and legs with biscuits. If you don’t own a biscuit joiner but still want to build this project, you can simply nail or screw the parts together and fill the holes. We used a table saw to cut the 1-1/2-in. square legs from 2x4s and a router with a 45-degree chamfer bit to bevel the edge of the top. If you don’t have a table saw or router, you can just use stock 2x2s for the legs and leave the edge of the top square.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
As for schooling, many local school districts, community colleges and woodworking stores offer woodworking classes, but those are a mixed bag. A handful is really good and many are terrible. There’s also a big difference between woodworking for fun and doing it for a living, and most classes are geared towards hobbyists. Out of all the proper woodworking schools with good reputations, I’ve only had personal experience with Marc Adams School of Woodworking. That place I recommend 100%, as the instructors are generally active professionals in their specialized niches, so one can always pick their brains for extra information related to earning a living. The director of the school also does a good job of screening instructors to eliminate the ones that don’t interact well in a classroom setting.
×