After investing a number of weekends building a nice table or chest, how are you going to finish it? Finishes beautify and protect the piece you’ve worked so hard to build so don’t cop out and do the “rub it with oil” thing. There are so many beautiful finishes that become second nature to work with. I use shellac 99% of the time. Once you get the feel down, it’s really quick to apply, very forgiving, easily repairable, and you never have to clean a brush (because it re-softens in alcohol)! There are other varnishes that provide good protection for outdoor use as well. I recommend picking up a good starter book, like Jeff Jewitt’s Hand Applied Finishes. It is simple and straightforward, without getting too far into minutiae.
A tri-sectional bookshelf, with sufficient space to house books or can be used for storage too. Its low level design can be dually used as a bookcase as well as a bench. So, one doesn’t need to walk to a bookshelf situated in some area of the house, to grab a book, but can sit on this bench and pull one out from the lower section. How convenient is that!
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
Woodworking was essential to the Romans. It provided, sometimes the only, material for buildings, transportation, tools, and household items. Wood also provided pipes, dye, waterproofing materials, and energy for heat.[5]:1Although most examples of Roman woodworking have been lost,[5]:2 the literary record preserved much of the contemporary knowledge. Vitruvius dedicates an entire chapter of his De architectura to timber, preserving many details.[6] Pliny, while not a botanist, dedicated six books of his Natural History to trees and woody plants which provides a wealth of information on trees and their uses

Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.

A mechanical reasoning or aptitude is also essential, mainly because woodworkers work with such a variety of machines and tools.  A tool in the hands of an untrained or inexperienced woodworker is a recipe for disaster. Woodworkers should understand and be able to apply mechanical principles to solve any problems they may encounter. Critical thinking skills are important too as woodworkers may face unexpected problems that need to be handled quickly. In this way, woodworkers can use reasoning and logic to foresee any potential problems, and develop solutions before mishaps happen.


Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.
Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
Why not make a little profit yourself with a little adjustment?The blocks aren’t too difficult to make, so once they’re made, try offering potential buyers the ability to customize the blocks. You can add names of family members on the blocks to make a “Jenga Family Tree”, or perhaps throw some math equations on their as a sort of “Jenga Flash Card” set for budding children.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.

A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Then, beginning several decades ago, shop classes began to be removed from secondary curriculums. With the decrease in educational funding, and increasing emphasis on standardized testing, schools began to cull electives, institute stricter graduation requirements, and focus more on college prep academics and the subjects necessary for passing state exams. There wasn’t money or time to maintain tools and sawdust-filled workshops, and one by one school districts dropped their shop classes, figuring that students who wished to pursue trade skills could do so later at a vocational college.

here's my 6x6 version build with #2 pine. shelves are 1x10 and threaded rod upsized to 5/16" to allow for extra width. center upright spaced at 1/3 side to side. this is very complex structurally - all the commenters who don't believe it should build it to really feel how it works. it is basically like a post-tensioned high rise. i think i'd like to paint the uprights and stain the shelves.
7. The dimensions of the furniture in our furniture plans can be usually easily customized. Do this carefully, especially if you do not have enough experience in making similar pieces of furniture. Analyze the facts about how the change of dimension of one furniture part affects the position and dimensions of other parts, as well as the stability and functionality of the finished project. Dimensions of the furniture have direct effect on whether the piece of furniture will be comfortable and useful for all of us. Any experienced carpenter should be familiar with the basics of the ergonomics and anthropometry.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.
Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
As far as shelves go, they’re not too efficient at holding much (six pieces of wood with the only piece used for storage), but they look quite pretty and are quite easy to make. You can usually charge double for these shelves compared to the traditional floating shelves, and with a little customizable paint option, you can dominate the contemporary scene with these neat looking shelves.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 917 S. Lusk Street, Suite 200, Boise Idaho, 83706, USA and used by permission. ClickBank's role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.
I have never claimed to be an expert furniture maker. I probably have more experience in a kitchen than a workshop, having spent 18 years as a chef. But it was probably my abilities to run a commercial kitchen that have led to my success at running a school. Planning and logistics is everything in a kitchen and it is the same with running a successful school.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Since money and space are usually in high demand, you want your purchases to make sense and work for you as far into the future as possible. To do this, the focus should be how to expand your capabilities rather than getting one project done quickly. With this in mind, and based on what I've learned over the past three decades, here's how I would proceed if I were starting over now.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
Biscuits (not the kind you eat). When you get into the details of how to build a bookcase, you’ll discover dozens of joinery options. Our editors simplify those options by focusing on biscuit joinery – a fast and easy way to line up all the boards in your project and get on with the gluing and screwing. You’ll also learn a little about pocket screw joinery in our free bookcase plans.
Jim, I belong to Charles Neil’s website and get his DVDs and watch his videos. He’s a great teacher. However, if I had to travel all the way up to Virginia I’d be out of luck. The Internet is a great asset for woodworkers. BTW, I wish the college you teach in was right here in my town. If it were I’d enroll because I know that you are a fine woodworker. Traveling somewhere to a class is an expense that I couldn’t afford in money and time.

Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.
Today, in our age of plastic and factories, woodworking has transformed from a common necessary skill into something almost mysterious or awe-inspiring. Because most 21st-century consumers are used to driving to big box stores to pick up another mass-produced replacement when their desk falls apart or their chair breaks, any man today that can walk up to a lumber pile with saw and plane to shape a beautiful and enduring replacement is revered as a “true craftsman.”
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.

Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.

For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
Teds Woodworking is a big collection of woodworking plans and all of these are well organized and categorized so that you find what you are looking for fast. These woodworking plans include bed plans, table and chair plans, furniture plans, shed plans, bird house plans and many more. Each of these woodworking plans come with full comprehensive instructions as well as diagrams. You will be able to see, what it is you want to do. The program also includes 150 training videos, so you can see and learn how things should be done. You will be able to see the complete pieces that you need to build and learn how to fit them together. The diagrams are used by many individuals as they go through each part of the process.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.


If you`ve found the diy bookshelf plans  below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.)   So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
Steely blue walls and a few intricately placed wood slices will give your bathroom a great rustic look. You will need several wood slices to go all the way around the room and then just place them in geometric patterns or however you want. Thin wood slices will affix to the walls easily with wallpaper glue or you can use a hot glue gun if you prefer.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.

Some might expect to see a cordless drill on this list, but when we're talking about basic power woodworking tools, a corded drill is more versatile and powerful. Sure, the cordless is, well, cordless, which makes it more portable, but corded drills are less expensive and can do more than a cordless drill. There are some options to consider when choosing a corded power drill, such as whether you want a 3/8-inch or 1/2-inch chuck, keyed or keyless chuck, straight drill or hammer drill, and so on. Learn all about these options (along with some suggestions on what to look for when shopping) in this article on corded power drills.
×