Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Historically, woodworkers relied upon the woods native to their region, until transportation and trade innovations made more exotic woods available to the craftsman. Woods are typically sorted into three basic types: hardwoods typified by tight grain and derived from broadleaf trees, softwoods from coniferous trees, and man-made materials such as plywood and MDF.Typically furniture such as tables and chairs is made using solid stock, and cabinet/fixture makers employ the use of plywood and other man made panel products.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Jim, I belong to Charles Neil’s website and get his DVDs and watch his videos. He’s a great teacher. However, if I had to travel all the way up to Virginia I’d be out of luck. The Internet is a great asset for woodworkers. BTW, I wish the college you teach in was right here in my town. If it were I’d enroll because I know that you are a fine woodworker. Traveling somewhere to a class is an expense that I couldn’t afford in money and time.
Looks very opulent especially in a living area where the family likes to unwind with each other. These book-cases have ample storage space for books, housing shelves at multiple levels for decor items too. The middle portion of the bookcase if left blank can be used as a space for the television unit, serving as a complete entertainment area in the house.
oh yeah, and buying a bunch of cap nuts is not so easy unless you order ahead of time. i went to two hardware stores (one family owned and one big box) and they kind of laughed at me when i said i needed 32. so i got regular nuts, tightened them so they were flush with the all thread on the front side, hammered it against the board and tightened the back side while holding the front one in place with a wrench. so, some of them have a little bit of overhang on the back side, but i don't have to worry about gouging skin while walking past it. for my next set, i'll order the cap nuts in bulk from ebay ahead of time...
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ... More + Product Details Close
Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.