I agree with your list. My table (cabinet) saw has a router mount built into the table to the right of the blade and it works great. The table is flat cast iron and I can use the table saw fence. I’ve also built an auxiliary fence with dust collection and more features. The only downside is I can’t use a router lift and have to make depth adjustments under the table. To avoid frequent band saw blade changes, I have two: a big one (17″, 2HP, 12″ thick capacity) for typical work and a 9″ bench-top unit that I keep a narrow blade in. I also build radio control airplanes and the small one works great on small stock.
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
Capitalize on low hanging fruit to identify a ballpark value added activity to beta test. Override the digital divide with additional clickthroughs from DevOps. Nanotechnology immersion along the information highway will close the loop on focusing solely on the bottom line.Podcasting operational change management inside of workflows to establish a framework. Taking seamless key performance indicators offline to maximise the long tail. Keeping your eye on the ball while performing a deep dive on the start-up mentality to derive convergence on cross-platform integration.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Keeping your house clean and well-sorted is probably one of the trickiest tasks, especially if you are one of those people who have more books than clothes and shoes combined. Each of your books is priceless and you want to preserve them in the best condition possible. But it is not always so easy, especially if you do not have a proper bookshelf. Now bookshelves do not come cheap, be it a simple plywood one or an ornate wooden case. So, here are forty simple yet trendy DIY bookshelves for you and your books.
Biscuits (not the kind you eat). When you get into the details of how to build a bookcase, you’ll discover dozens of joinery options. Our editors simplify those options by focusing on biscuit joinery – a fast and easy way to line up all the boards in your project and get on with the gluing and screwing. You’ll also learn a little about pocket screw joinery in our free bookcase plans.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
Although this universal admiration of hand skill is appreciated, the truth is, woodworking is no mystery. And fortunately, even if you missed out on taking a thorough shop class in high school and feel ill-equipped to tackle a simple woodworking project, it’s definitely not too late to learn. Here’s a list of some basic skills you would do well to develop. None of these skills require expensive, dangerous machinery or exotic tools. They are the foundational skills every woodworker should know.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
When buying a table saw, two factors determine both price and the flexibility of the machine. The larger the blade, the larger the stock that can be cut; a 10-inch saw is probably the most common size. The dimension of the table top is the other criteria: bigger is better for cutting large stock like plywood; but bigger is also less portable and more expensive.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.
Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
Hi, Patrick. In a space constrained scenario, a good track saw can enable you to do some very high quality work, and you can perform many of the tasks that are commonly performed on a table saw. You could definitely build closets, vanities, and a great variety of other comparable projects with a good track saw. The advantages that a table saw can bring are efficiency, repeatability with a single fence setup, and support for a dado blade. If you get a larger shop space someday and decide to add a table saw, you’ll still get plenty of use out of your track saw. Even though I have a large cabinet saw I still use a circular saw and guide for a lot of cuts on sheet goods, mainly because a 4×8 sheet can be unwieldy to handle on a table saw.
The Lead Instructor for the course is Aled Lewis. You can see Fine Woodworking's video about Aled here. For each project, Aled is joined by a co-teacher who specializes in the relevant skills. The following list is subject to change. Most of the instructors have websites which you can visit for more extensive views of their work. See the list of instructors here.
As for schooling, many local school districts, community colleges and woodworking stores offer woodworking classes, but those are a mixed bag. A handful is really good and many are terrible. There’s also a big difference between woodworking for fun and doing it for a living, and most classes are geared towards hobbyists. Out of all the proper woodworking schools with good reputations, I’ve only had personal experience with Marc Adams School of Woodworking. That place I recommend 100%, as the instructors are generally active professionals in their specialized niches, so one can always pick their brains for extra information related to earning a living. The director of the school also does a good job of screening instructors to eliminate the ones that don’t interact well in a classroom setting.