Hi Scott – Your nearest decent sized town should have a flea market or craft store. Rent the space, fill it up, and check back every couple of weeks to get your money and restock. I tried craft shows and they were a bust and too much work loading, unloading, setting up, reloading, taking down the set up, unloading what did not sell into your garage. As with lots of things, the craft show promoter makes most of the money.
Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.

Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
4. Selection of furniture plan: Before you start making furniture based on some plan, analyze it thoroughly. Make sure if the furniture plan has all the necessary dimensions and informations, and is it made properly. A bad and incomplete furniture plan will result in the poor quality of the final product and you will spend more money finishing it. If the dimensions of the furniture pieces do not match and you realize that only during its assemblage, you will have to throw away all the material, not to mention the time that you’ve lost with it… Choosing a quality furniture plan is another basic requirement to make the quality furniture.
Woodworker’s work environments vary depending on job duties.  If a woodworker is employed to handle and cut large heavy materials, he or she may work in a factory setting. Cabinet and countertop woodworkers typically work in large or small manufacturing plants. Some woodworkers work in sawmills, while other’s work out of home shops.  In 2014, there were just over 237,000 jobs for all woodworkers, with other wood product manufacturing employing 23 percent; wood kitchen cabinets and countertop manufacturing employing 21 percent.  Most woodworkers work a regular, full-time workweek.

Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)

Woodturning is the craft of using the wood lathe with hand-held tools to cut a shape that is symmetrical around the axis of rotation. Like the potter's wheel, the wood lathe is a simple mechanism which can generate a variety of forms. The operator is known as a turner, and the skills needed to use the tools were traditionally known as turnery. In pre-industrial England, these skills were sufficiently difficult to be known as 'the misterie' of the turners guild. The skills to use the tools by hand, without a fixed point of contact with the wood, distinguish woodturning and the wood lathe from the machinists lathe, or metal-working lathe.
Each bookcase door has a fixed middle shelf and four adjustable shelves. The doors are available in hardwood veneers, MDF or vinyl-lam. Bookcase sizes range from 36in. to 66in.wide and up to 96in. high. Order them directly from the manufacturer. The system, weighing 400 lbs., will show up on a single pallet. Prices start at $2,200 (plus shipping) for the entire system.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..

Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
You can find a project for just about every room in your home. Table scape trays make perfect platforms for dining room decoration. Wooden plaques offer a blank slate for any saying or picture you want. If you want a unique table, we’ve got a few options to consider. Headboards and benches can give your bedroom a real transformation. You can find anything you want among these DIY wood craft projects.
But what if you want to make a box? The revered (and overly-mystified) dovetail joint is a very strong way to join corners of boards. Of all features that non-woodworkers admire today, the dovetail joint is the one that creates the most awe. It is composed of one side cut into wedge-shaped “tails” that mate into corresponding “pins.” When fitted together, the wedge shape prevents the boards from sliding apart in one direction. This joint has been very standard construction since the 1700s. Never meant to impress, it was usually intentionally hidden behind veneer, molding, or paint so that no one would have to look at that “ugly” joinery. It wasn’t until the arts and crafts movement that visible joinery was considered an aesthetic asset. Today, making dovetail joints has become a litmus test for serious woodworkers, but don’t let this scare you away from trying it. Check out a few of the four million “How to Cut Dovetails” videos online and then get into the shop. It’s much more straightforward than people think: Cut tails. Trace the tails on the other board. Then cut out the waste you traced. That’s pretty much it. All the fine tuning is just practice.
Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
There is significant evidence of advanced woodworking in Ancient Egypt.[1] Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.[2
Offerman notes that there’s something elemental and healthy about using both your brain and hands to solve a problem or build something, and woodworking fits the bill perfectly. Building things is a hobby anyone can enjoy and learn from, no matter what you do for a living. If you’re brave enough to pick up some tools and give it a shot, bully for you.

Add a little rustic décor to your walls by building a wooden mail sorter. Not only does this give you beautiful rustic décor, it also serves a very handy function by keeping mail neatly organized. You just need a few pieces of wood and some small coat hooks at the bottom to hang your keys. Stain it in any color you want and you have a very functional and very beautiful sorter.
This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.
Tightening the nuts clamps the uprights against the shelves, holding them in place and providing shear strength (through friction) for the whole assembly. I know of an 8' tall, 12' long version of these shelves that has survived a few minor earthquakes while fully loaded with hundreds of books. Once the nuts are tightened on my smaller versions, I (all 240lbs of me) have a very hard time "racking" the shelves by pushing on one end of them in an attempt to get them to collapse: I can't.

Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.


You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.

The Saw Guy - Saw Reviews and DIY Projects Copyright © 2018. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
×