Mike Siemsen literally takes you step by step (in "The Naked Woodworker"), going from "I've got nothing" to a full set of inexpensive used tools, and bringing them back into usable condition, then building your own bench and saw-benches. All for about $700. That will set you up with just about everything you'll need to make most furniture (moulding planes, plough planes, combination planes are ... extra-curricular). $700 spent on new power tools... doesn't get you nearly as far.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
Kids love to watch grown-ups use woodworking tools, but what they love even more is making the sawdust fly themselves. With minimal equipment and adult help, your child will soon be turning out a wonderful variety of toys, games, gifts, household objects, and holiday decorations. These 50 easy and inexpensive projects are arranged by age and skill level.
Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
My basic advice is to develop lots of connections with people. Most branches of woodworking are hard to sell without knowing the right people – especially when targeting the luxury furnishings or corporate markets. I started down this path with the idea that I might own my own shop but forgot about that once I’d accepted employment in the field. Since I was satisfied working for others, I didn’t bother making the connections, and now I’m so busy it’s hard to get away from the shop long enough to do so. That’s not the end of the world, as we’re still pulling in plenty of work. It just took longer to get there than it should have. For those considering a self-employed woodworking career, it’s a good idea to meet individuals who associate with the types of people that are likely to become future clients. Word-of-mouth is still a powerful form of marketing even in this age of internet.
Picture it: eight people with different skill levels, each trying to design a different project (which, by the way, they have no idea how to do) and hopefully cutting some wood by the third class. Meanwhile, the instructor is running from student to student, and then running to the table saw where a kickback has occurred. It is no wonder that at the end of the class not a single thing has been made and most of the students don't come back.
With your tools set up and ready to go, you’re ready to get started on woodworking projects. If you’re looking for beginner woodworking projects, we’ve got you covered. Projects range from birdhouses to jewelry boxes; there’s something for everyone. You’re sure to find a project that’s a good fit for your skills and tools, and that you’ll enjoy creating.
I generally use biscuits for this (three per joint), and I have never had a joint fail (and a bookcase spending five years in an elementary school is a pretty fair test), but dadoes work great here as well. To assist with accuracy and consistency when using biscuits, mark your biscuit locations on a piece of scrap, and then use the scrap as a guide as you mill biscuit slots in each carcass member. The carcass top is attached so that it is flush with the top of the carcass sides. The carcass bottom is attached so that the top of the panel is 2-1/2″ above the floor (or the bottom of the side panel).
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
If you enjoy these free bookcase plans be sure to check out these other free woodworking plans for shelves, coffee tables, entertainment centers, desks, Little Free Library, wine racks, jewelry boxes, home bars, kitchen islands, bathroom vanities, playhouses, picnic tables, dog houses, decks, workbenches, tree houses, pergolas, sheds, Adirondack chairs, bunk beds, and even chicken coops.
At some point dust collection needs to be considered. For safety reasons all power tools should run in conjunction with a good dust collection system. However the reality is that many woodworkers will put up with the dust for a while, if not forever. There are machines that really can't be run without dust collection such as a large planer or a bandsaw. The chips and sawdust must be extracted or else the buildup will damage the machine. A large shop vac may be sufficient for smaller machines, and portable dust collectors are available that can be moved from one machine to another. Dust collection is a reasonable investment that should actually be made early on. Your health is well worth the cost.
Biscuits (not the kind you eat). When you get into the details of how to build a bookcase, you’ll discover dozens of joinery options. Our editors simplify those options by focusing on biscuit joinery – a fast and easy way to line up all the boards in your project and get on with the gluing and screwing. You’ll also learn a little about pocket screw joinery in our free bookcase plans.
Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup?
Why not make a little profit yourself with a little adjustment?The blocks aren’t too difficult to make, so once they’re made, try offering potential buyers the ability to customize the blocks. You can add names of family members on the blocks to make a “Jenga Family Tree”, or perhaps throw some math equations on their as a sort of “Jenga Flash Card” set for budding children.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ... More + Product Details Close
Dividers (or compass) are used for taking and repeating a measurement over and over again on a work piece. Traditional woodworkers rarely take measurements with a tape measure when doing fine joinery work, but rather take a measurement with dividers then transfer that arbitrary (yet accurate) measurement to another work piece. This removes a degree of inaccuracy.
After experiencing working in the wedding rental industry, I knew it wasn’t something I wanted to do long term and sold my business. My wedding and vintage rental business had reawakened my creativity though. After learning how to build farm tables, I became hooked on building and making things. And knowing how to build other things became much easier, as well as learning to use different tools. It’s like once you know how to do one thing related, the rest just flows.
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.) So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
We’ve already done rope, and now we’re on to another rustic material we love: wood! It’s as basic of a material as clay and is constantly reinvented by DIYers, crafters, artists, hackers, and carpenters. To get inspired to create our own batch of cool wooden objects, we turned to our favorite fellow makers to see what projects they’ve come up with. Scroll down for our top DIY wood project picks.
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
As part of the job, woodworkers prepare and operate saws, drill presses, routers, sanders, lathes, shapers, milling machines, and planers. Often using a template, woodworkers measure and verify dimensions, cut, and shape wooden parts. Woodworkers stain or coat the wood products with sealers and topcoats, such as varnish and lacquer. But, they also often install hardware, fit electrical components and specialty products, such as metal trims and glass.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
So my partners and I opened a Woodcraft store that had an established school as a main part of its business plan. What could be better? Come for a class and buy some tools. But when I first presented the idea of a full-fledged school to the corporate people and told them the dollar amount that I planned to do in school tuition sales, they basically laughed at me. A year after we were opened, they finally started to take notice of this whole "education thing" because I had not only met my projections, I doubled them.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Each bookcase door has a fixed middle shelf and four adjustable shelves. The doors are available in hardwood veneers, MDF or vinyl-lam. Bookcase sizes range from 36in. to 66in.wide and up to 96in. high. Order them directly from the manufacturer. The system, weighing 400 lbs., will show up on a single pallet. Prices start at $2,200 (plus shipping) for the entire system.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
Hi Scott – Your nearest decent sized town should have a flea market or craft store. Rent the space, fill it up, and check back every couple of weeks to get your money and restock. I tried craft shows and they were a bust and too much work loading, unloading, setting up, reloading, taking down the set up, unloading what did not sell into your garage. As with lots of things, the craft show promoter makes most of the money.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
Just create stunning “professional woodworking projects” with the step-by-step instructions given in a blueprint to participate in 16,000 completed woodworking projects. Just read the simple steps that you should follow before doing it practically, and you will feel confident all the time. With the simple “hand holding” instructions, you can complete the wood project in very little time.
A mechanical reasoning or aptitude is also essential, mainly because woodworkers work with such a variety of machines and tools. A tool in the hands of an untrained or inexperienced woodworker is a recipe for disaster. Woodworkers should understand and be able to apply mechanical principles to solve any problems they may encounter. Critical thinking skills are important too as woodworkers may face unexpected problems that need to be handled quickly. In this way, woodworkers can use reasoning and logic to foresee any potential problems, and develop solutions before mishaps happen.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.
How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.
I know this is an old forum topic, but I felt the need to chime in. I was in Jr. High back in the late 70s and my school had a wood shop and I still have a cutting board and a three leg single post foyer table made from those shops and very proud of them. It is sad seeing the lack of “hands on” classes these days in schools because of liability issues. Just recently got back into woodworking last year and honestly Marc has much to do with that and his YouTube videos, that and a date night where my wife and I went to a Woodcraft class for making pens. I plan on joining the guild at some point but wanted to get enough tools and skills together to make the guild worth it for me and I am almost there. I am currently working on the 2015 Kids Table from Woodworkers Fighting Cancer and will donate to them as well when I finish even though it is way past due it is the perfect project for my daughter. Since I started I have made pens, cutting boards, a toy airplane and now working on this table and love it. Thank you Marc for being such an influence on this community!!
To add some additional dimension to the bookcase, you can use corner posts to dress up the bookcase. I like to use a contrasting wood to highlight this element (such as maple posts with walnut carcass as shown), but this is a stylistic preference. The posts can be square, or tapered. I prefer to cut these as tapers, using a band saw to make the angled cuts on the two outside surfaces of each corner post.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.