Don’t follow the temptation to cheap out and buy a cheap combination square. Because, like me, you will eventually have to replace it because of its inaccuracy. If you want your joinery to fit perfectly, then you need to scribe it accurately with precise marking tools. Unfortunately there is really only one company (that I know of) that makes a super accurate combination square. But fortunately it is amazing, and I use it daily. I’ll talk about it in-depth in the Layout & Measuring Tool Buying Guide.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
Getting started in woodworking can seem like a daunting task. From specialty woodworking tools to identifying and understanding the different types of wood, there is so much to know that even the old-timers are still developing. But learning and experimenting are what woodworking is all about. Get started on the right foot with some essential basics about safety, tools, lumber, and traditional layout and measuring techniques.
Another option is the circular saw mated with a metal guide (known as a track saw ). These systems have quickly come into their own and can deliver exceptional results. They are ideal for both ripping and cross cutting sheets of plywood, but can handle solid stock if it is wide enough. These systems can cost as much as a table saw but they are compact and very portable.
Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.
You should also double-check the length of your all-thread rods. I'd dummy one up and try it out before cutting all of them. It needs to be just long enough to catch a couple of threads and snug down without punching out through the cap nut. The actual "cap" portion of cap nuts is fairly thin, and if the all-thread is even a bit too long it will punch through the end when you snug it up.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
There are several ways to complete this task, including pocket screws, brads or biscuits. I have used all of these methods, but my preference is biscuits, as they provide adequate strength, excellent alignment, and ease. I generally just place one biscuit in the center of each rail and stile, which provides alignment assistance while not being overly constraining when manual adjustments need to be made to achieve desired placement. After applying glue and biscuits, use lots of clamps to create a gap-free bond between the face frame and carcass.
Woodturning is the craft of using the wood lathe with hand-held tools to cut a shape that is symmetrical around the axis of rotation. Like the potter's wheel, the wood lathe is a simple mechanism which can generate a variety of forms. The operator is known as a turner, and the skills needed to use the tools were traditionally known as turnery. In pre-industrial England, these skills were sufficiently difficult to be known as 'the misterie' of the turners guild. The skills to use the tools by hand, without a fixed point of contact with the wood, distinguish woodturning and the wood lathe from the machinists lathe, or metal-working lathe.
7. The dimensions of the furniture in our furniture plans can be usually easily customized. Do this carefully, especially if you do not have enough experience in making similar pieces of furniture. Analyze the facts about how the change of dimension of one furniture part affects the position and dimensions of other parts, as well as the stability and functionality of the finished project. Dimensions of the furniture have direct effect on whether the piece of furniture will be comfortable and useful for all of us. Any experienced carpenter should be familiar with the basics of the ergonomics and anthropometry.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.
Dust Collector. A dust collector works at the source of creation. It’s main purpose is to collect the dust right from the place you are cutting the wood. A lot of power tools come with a dust collector extension which allows the dust collector to be attached to them directly. This means a lot less cleaning up for you to do. Dust collectors come in two types, single bag and double bag. Single bag ones are more common.