Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Now install the vertical stiles. Hold each stile against the front edge of the bookcase sides, then transfer the biscuit­slot locations from the sides onto the stile. Cut slots using the biscuit joiner, apply glue to both surfaces, insert biscuits into the slots and press the stile home. Use a rubber mallet to tap it tight. Repeat the glue-and-­biscuit routine to attach the horizontal mahogany aprons to the shelves. Prior to installation, I routed a decorative profile along the bottom edge of each apron to create shadow lines that accentuate the shelves. The aprons are more than decorative, though. They stiffen the shelf to prevent sagging. Trim the top of the bookcase with crown molding [ 8 ] and the bottom with base molding [ 9 ]. Wait 8 to 10 hours for the glue to cure before filling the shelves.

With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.


This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Just create stunning “professional woodworking projects” with the step-by-step instructions given in a blueprint to participate in 16,000 completed woodworking projects. Just read the simple steps that you should follow before doing it practically, and you will feel confident all the time. With the simple “hand holding” instructions, you can complete the wood project in very little time.
Lots of ways. Woodworking really reinforces my independent nature. Blogs are good. Norm Abrams videos. I have a library of magazines and books with really neat projects which I love to read over and over to get a sense of how other woodworkers think through their creative projects. I have a painter friend with whom I endlessly brainstorm how to finish the final wood project. But really, the wood itself teaches me the most. Each species has different needs. The projects also teach me. Each project is unique in approach, design, and method. I’ve learned to listen and make myself a servant of these things. I come to the shop ready to learn.
In being self-employed, one day will greatly vary from the next, but generally, I start in the morning by dealing with in-town errands or head right to the shop if there are none. Once at the shop, there’s an e-mail check, then a brief glance at various websites to look for new developments related to our market and clientele. Then the real workday starts. I’ve got a bunch of notes regarding current projects taped next to my computer and will make a list for the day’s tasks by picking the highest priority items from the notes. The goal is to get that stuff accomplished by the end of the day. There are two of us in the shop, but we usually work on separate projects, so that’s why I have my own to-do list. Some days are spent on the computer designing or creating programs for the laser or CNC. Other times we’re doing runs of sunglasses or guitar parts which we sell wholesale to other businesses. In which case, I may be operating the laser or CNC. Despite the high-tech tooling, there’s still a lot of bench work to do, and that can involve cutting and fitting joints with chisels and hand planes. Besides that, there’s always plenty of rough lumber to mill since no project can begin until boards are flattened, surfaced and cut to dimension.
Marc, it’s very difficult to answer this question. Many years ago i started out with a book, and then i got another but i just wasn’t getting it. Then I started watching your video’s and everything came to life. I know there are many options that you would fall under but in my personal opinion there needs to be a Woodwhisperer choice or at least a Pod casting choice =)
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
The table saw is the center of most workshops; it is the largest and most imposing tool in the shop. While it is an important tool, one could claim that table saw need not be on this list. However, it is an important tool and shows that creating a shop is not a matter of just collecting hand tools. There are jobs that hand tools cannot do as well as tools like the table saw, especially when there is such a wide variety of blades which can be set up and changed for so many different applications. Table saws create straight and consistent cuts. When setting up a table saw for a cut, one needs to set the depth of the blade and adjust the fence according to the width desired.
Each bookcase door has a fixed middle shelf and four adjustable shelves. The doors are available in hardwood veneers, MDF or vinyl-lam. Bookcase sizes range from 36in. to 66in.wide and up to 96in. high. Order them directly from the manufacturer. The system, weighing 400 lbs., will show up on a single pallet. Prices start at $2,200 (plus shipping) for the entire system.

My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.


The router is a hand held tool which is often mounted upside down and is used to hollow out an area in the face of a work piece. It is also used to cut profiles for moldings and adding decorative edges to any piece enhances its beauty and dimension. Routers are also used to cut joinery, such as dovetails and dados. The beauty of a router is that one can purchase an unlimited number of profiles to best suit the many requirements which arise with woodworking.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Wondering if you are still hanging in there Scott? One thing I notice woodworkers often do when getting started (including myself) is they sell their hand made items way too cheap, it doesn’t help anyone except the customer. You say yourself that they sell as fast as you can make them. Put your prices up! Double or even triple, the amount of orders may slow down but you will be doing yourself a favour. Don’t bother with Etsy or Craigslist or local markets in my opinion. Build it up for yourself to make money not making the giants even richer from all your hard work. I’ve been selling my woodwork online since 2004, before all these giants came along. I feel I have the experience to offer advice if anyone is interested. Trust no one! The internet has become a place for giants to make money off you (Facebook, Etsy, GoogleAds, Amazon…… the list goes on.) Don’t let them take your money, learn how to use them to your advantage instead of being a sucker and paying them money to grow even bigger while you stay the same size. They don’t care about you, they only care about their own business models. Grow your own business brand and ignore anyone who appears to want to help you, especially if their main business is making money online. That’s all they care about! Not you. Invest your time and money in yourself, your own website – not others and you will succeed, providing you are doing what you love and are passionate about.

If you are wanting to build great looking chairs for your patio you've come to the right place. I bought a home late last year and didn't have any patio furniture whatsoever. My dad had built a beautiful piece for their home and so I credit him with design help and the inspiration to build my own. This setup is perfect for enjoying a relaxing evening out on the deck with friends or family. I built my chairs out of cedar because cedar does not rot and stands up against the outdoor elements quite well. You can use pine as long as it is painted or coated with a thick finish of poly.


thank you, thank you, thank you!! the lumber that i had in the garage wasn't exactly what your plans called for (2x4s and 1x10s), so i adjusted the length of the all thread to accommodate the depth. also, one of my 2x4s was kind of wonky and i was worried it would jeopardize the stability of the set - but it's totally solid! the shelves are level and aren't going anywhere!! :) (i threw all of my body weight against it, and it's totally solid!) it's approx. 4' wide by 7.5' tall.

MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.


Use 1x12 pine lumber for a rustic appearance. Nothing looks like pine with its large knots and swirls. And because you're using solid lumber, you can sand the edges smooth for a finished appearance. Add a 1/4-inch fir plywood back for strength and stability. Note that "1x12" is a nominal size. The actual size will be ¾-inch thick and 11 ¼-inches wide.

This bookcase lets you have plenty of storage for your books, without you having to show it openly. With a locking system, light mechanisms and a lot of built in shelves, this design form maybe the most high tech of all the others we have discussed. Many interesting features such as a folding door, leading to another area of the house, which a guest may never know- completely steal the show!

In order to be successful in woodworking, there are skills absolutely necessary to know and master.  Many of these skills were once taught in high school’s all across the nation, but today, most woodshop classes have been suspended, and people must learn through college classes, apprenticeships, internships, from professionals, or by trial and error. 


On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.

Apply 2 coats of Urethane with a brush. Let the second coat dry completely (6-12 hours), then lightly sand the armrests, table, and areas you come in contact with when sitting (chair slats). This light sanding with 220 grit paper will remove any dust particles that settled in the first coat. Next, take a clean cloth and wipe a thin coat of poly on all the areas you sanded. This will give you a nice smooth finish. Once dry, enjoy your new furniture and have a barbecue!


For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
The Nine-month Comprehensive is designed for aspiring professional furniture makers and dedicated amateurs who seek in-depth training at the highest standard of excellence. The hands-on, project-oriented format includes the full range of furniture making skills. Sequential projects take students from the fundamentals through the fine points of design and craftsmanship.
I know this is an old forum topic, but I felt the need to chime in. I was in Jr. High back in the late 70s and my school had a wood shop and I still have a cutting board and a three leg single post foyer table made from those shops and very proud of them. It is sad seeing the lack of “hands on” classes these days in schools because of liability issues. Just recently got back into woodworking last year and honestly Marc has much to do with that and his YouTube videos, that and a date night where my wife and I went to a Woodcraft class for making pens. I plan on joining the guild at some point but wanted to get enough tools and skills together to make the guild worth it for me and I am almost there. I am currently working on the 2015 Kids Table from Woodworkers Fighting Cancer and will donate to them as well when I finish even though it is way past due it is the perfect project for my daughter. Since I started I have made pens, cutting boards, a toy airplane and now working on this table and love it. Thank you Marc for being such an influence on this community!!
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
The Japanese saw is a favorite. A much smarter, efficient and exact cut can be made using this saw as opposed to a European saw. The difference between the two is simple: tooth direction. European saws cut when pushing the saw as opposed to Japanese saws which cut on the pull. One uses much less energy when pulling - perhaps that is why the horse was put in front of the cart. A Japanese saw is a must have in any shop.
This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
A while back we stumbled upon this awesome industrial bookcase from Pottery Barn for $1900! I knew we could do it for a lot less so we posted it on Facebook for some reader feedback and it was a resounding YES! So I got to work. After a couple of weeks and 1000 mile move to Michigan we are finally finished and couldn’t be happier with how it turned out. And it only cost us about $275! The pipe is what drove this project cost up however it is still a far cry from the $1900 Pottery Barn price tag and well worth it if you ask me. Let us know what you think in the comments.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
Tightening the nuts clamps the uprights against the shelves, holding them in place and providing shear strength (through friction) for the whole assembly. I know of an 8' tall, 12' long version of these shelves that has survived a few minor earthquakes while fully loaded with hundreds of books. Once the nuts are tightened on my smaller versions, I (all 240lbs of me) have a very hard time "racking" the shelves by pushing on one end of them in an attempt to get them to collapse: I can't.
×