11. Other necessary skills: Each woodworker should have a basic knowledge of metalworking. Although most of the home furniture is made out of wood, in this category you may occasionally find some projects made out of metal, or the wooden furniture projects that have a decorative metal parts or fasteners. In our opinion, the combination of wood and wrought iron makes the most beautiful furniture.
Since this project contains two different finishes it is best to do the finishing before going any farther in the assembly process. We wanted to match the Pottery Barn finish as closely as possible so we went with the charcoal Chalked ultra matte paint from Rust-Oleum. I love the thick textured look of this paint. To brighten it up a bit and give it a cool look we decided to wax it with a Johnson Paste wax and a lot of elbow grease.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.

Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.


The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Learning how to use tools to create what you envision in your mind is one of the most rewarding activities a man can involve himself in. Even though many of us today missed out on this first-hand training in high school shop class, there are a lot of folks that are buying books and reading blogs all about it. By learning how to tune up their grandfather’s hand plane they are seeking to once again tap into that deep-rooted desire to create and build with the knowledge of their mind and the skill of their hands.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!

This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
thank you, thank you, thank you!! the lumber that i had in the garage wasn't exactly what your plans called for (2x4s and 1x10s), so i adjusted the length of the all thread to accommodate the depth. also, one of my 2x4s was kind of wonky and i was worried it would jeopardize the stability of the set - but it's totally solid! the shelves are level and aren't going anywhere!! :) (i threw all of my body weight against it, and it's totally solid!) it's approx. 4' wide by 7.5' tall.

You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.

If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
So my partners and I opened a Woodcraft store that had an established school as a main part of its business plan. What could be better? Come for a class and buy some tools. But when I first presented the idea of a full-fledged school to the corporate people and told them the dollar amount that I planned to do in school tuition sales, they basically laughed at me. A year after we were opened, they finally started to take notice of this whole "education thing" because I had not only met my projections, I doubled them.
Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood. 

It’s mostly been learn by doing for me. I can’t afford to go somewhere to take any lessons. However, I do learn from books, DVDs, and videos on the internet. I still believe that learning by doing is the best way. Books and videos can get you going in the right direction but when you do it on your own all kinds of problems crop up that you have to solve. For example, when woodcarving the best way to understand what carving with the grain is is to carve with a carving tool. Same thing about sharpening a carving tool. You had better learn how to sharpen by sharpening your tools when they need it. You’re dead in the water if your carving tools are not sharp.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close

More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
here's my 6x6 version build with #2 pine. shelves are 1x10 and threaded rod upsized to 5/16" to allow for extra width. center upright spaced at 1/3 side to side. this is very complex structurally - all the commenters who don't believe it should build it to really feel how it works. it is basically like a post-tensioned high rise. i think i'd like to paint the uprights and stain the shelves. 

1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
I was attracted to this page by the headboard. It looks great and it’s unique. I must disagree with the first sentence, that rustic is ‘in’ right now. I’m thinking, ‘It’s the great recession’. Any money I spend better get me the most refined thing I can afford. Kind of like how I believe that new store bought jeans with holes in them are going out of style like a cold cup of coffee.

Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.

Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
Since money and space are usually in high demand, you want your purchases to make sense and work for you as far into the future as possible. To do this, the focus should be how to expand your capabilities rather than getting one project done quickly. With this in mind, and based on what I've learned over the past three decades, here's how I would proceed if I were starting over now.
Please note that many of the links in this post are affiliate links which means I’ll get a small commission if you purchase any of the tools using them. This is what helps support the website so I can continue making free plans for you. Anything purchased on Amazon using the following link:http://www.DIYPETE.com/AMAZON will help support the site. So thank you for your support!
If you enjoy these free bookcase plans be sure to check out these other free woodworking plans for shelves, coffee tables, entertainment centers, desks, Little Free Library, wine racks, jewelry boxes, home bars, kitchen islands, bathroom vanities, playhouses, picnic tables, dog houses, decks, workbenches, tree houses, pergolas, sheds, Adirondack chairs, bunk beds, and even chicken coops.

In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Dividers (or compass) are used for taking and repeating a measurement over and over again on a work piece. Traditional woodworkers rarely take measurements with a tape measure when doing fine joinery work, but rather take a measurement with dividers then transfer that arbitrary (yet accurate) measurement to another work piece. This removes a degree of inaccuracy.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles. 

Looking for easy bookshelf plans? Well, worry no more. You are come to the right place. Any book or website maybe tell you that finding innovative ways to display and store books can be just as charming of the arts. And although you are the person who love for reading a lot of books and need to high budget to buy a bookshelf for storing and displaying the books. Designing and building your own bookcase is an easy project and you can easily build it to store your book, this way will save your a lot budget.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
Can a Makita or Festool Track Saw be a good substitute for a table saw? I’m new to woodworking and have a small shop space in the basement of my home. Doing some reading on several forums, many seem to prefer the track saw over a table saw. Will I be able to do cabinetry such as closets, bathroom vanities, etc with a track saw and track saw table setup? 

Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
Make It: Have your child paint 10 craft sticks and allow them to dry. Put a line of glue on the back of five sticks. Sandwich a piece of string between a glued stick and an unglued stick; clip them with clothespins to hold the glue securely. Let dry. Run glue along an unpainted craft stick, lay it horizontally and stick on the five strings as shown (don't let the sticks hang too low or they'll tangle in the wind). Top with another unpainted stick and add clothespins to hold the glue securely. Once dry, tie the strings together and cut off the excess. Hang outdoors and let the wind do its work.
With your tools set up and ready to go, you’re ready to get started on woodworking projects. If you’re looking for beginner woodworking projects, we’ve got you covered. Projects range from birdhouses to jewelry boxes; there’s something for everyone. You’re sure to find a project that’s a good fit for your skills and tools, and that you’ll enjoy creating.

A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.

Many beginners trying to get started in woodworking take one look at their budget and worry how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
Next, grab a role of tape to make your rounded corners for the arms and back supports. Do a rounded corner for the two outside armrests, and for both outside pieces of the table top. Create rounded corners for the top of the backrest supports as well(Part H). Cut with a jigsaw and use an orbital sander to smooth the edges. Check out photos in later parts of the project to see the rounded edges.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
As far as shelves go, they’re not too efficient at holding much (six pieces of wood with the only piece used for storage), but they look quite pretty and are quite easy to make. You can usually charge double for these shelves compared to the traditional floating shelves, and with a little customizable paint option, you can dominate the contemporary scene with these neat looking shelves.
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.
As projects increase in size and scale, there is usually a desire to get a larger table saw, a miter saw, add a small jointer, a router and maybe a belt sander. Eventually, things get out of hand and you are seen at every tool sale, and spend more time online looking at the few remaining tools for which you have not yet found a project that will justify their purchase.

Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.
When many people hear the word woodworker, the image of someone leaning over a workbench sanding a long piece of wood with his or her hands. However, modern woodworking requires training on highly technical machinery, such as CNC (computerized numerical control) machines.  Even woodworkers caught somewhere between modern equipment and a hand planer typically use CNC machines to fabricate large or intricate products.  If working for a large company, a lot of the work will be done on an assembly line or in various areas on the floor designated to complete a particular part of a project.   The tasks will be handled by different workers with very specialized training on each machine. For example, one machine might cut a large piece of wood into three sections, whereas another machine might take one of the sections and round each edge. 

To reduce the risk of personal injury and property damage, read and follow all related product manufacturers instruction manuals and information before performing any of the applications shown. Some construction-related applications shown may not be allowed in your local area. Consult your local authority having jurisdiction (AHJ) before starting work for information on permits, applicable codes, and other regulations. Black & Decker disclaims any responsibility for any damage to property or injury to persons as a result of misuse of the information provided.


This hand held sander is a great finish sander. When sanding, grain directions should be the first thing one looks at when deciding which direction to move the sand paper. With the random orbital sander, because of its circular movements, one does not need to take too much notice in the grain direction. Plus, with a velcro pad, switching sandpaper discs only takes a few seconds. Most sanders allow for speed control as well. This is an important feature because you do not want to over or under sand your work since what you leave behind after you finish sanding is going to exist.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.

If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.
Hi, Patrick. “When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw?” That is possible to do on either a cabinet saw or a track saw, and you can end up with the same result. If I were doing this in my shop I would do it on my table saw because I have one and it would be a quicker setup, but if I didn’t have a table saw I would use a track saw. I have a friend who builds beautiful furniture and cabinetry with a track saw, and he doesn’t feel that it limits what he can build.
If you are wanting to build great looking chairs for your patio you've come to the right place. I bought a home late last year and didn't have any patio furniture whatsoever. My dad had built a beautiful piece for their home and so I credit him with design help and the inspiration to build my own. This setup is perfect for enjoying a relaxing evening out on the deck with friends or family. I built my chairs out of cedar because cedar does not rot and stands up against the outdoor elements quite well. You can use pine as long as it is painted or coated with a thick finish of poly.
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.
Don’t be afraid to ask if there are internship or apprenticeship opportunities. Even if you’re declined, people will know you’re looking, and if you continue to hang out in their circles and demonstrate that you’d be a model employee, someone will take notice. There’s no shortage of woodworkers, but there is a severe shortage of enthusiastic and phenomenal woodworkers.
We'd been meaning to build these for over a year to replace a bulky entertainment center plus some cobbled together shelving for our TV wall. With a new 32" panel TV that only needed an 8" front-to-back shelf, this looked like a good choice! Since we live in rented housing, we couldn't attach anything to the walls but wanted something large enough to cover an exactly 8' x 8' wall without protruding the 27" into the narrow living room that the old furniture had while being "knock down-able" for future moves. Main problem = no real workspace for 8' uprights.

Use the Cutting List (see Additional Information, below) as a guide for cutting all the parts. The next step is to mark the shelf positions on the shelf sides. It’s important to keep track of the orientation of the parts. For reference, we placed a piece of masking tape on the top of each side, and on the top side of each shelf. Justin and Jackson used a framing square to draw lines indicating the bottom of each shelf (Photo 1).

Make It: Paint four clothespins black. Thread a 4-inch-long black chenille stems through the two holes of a large black button. Twist and curl the ends of chenille stems where they meet to form antennae. Glue googly eyes just below the antennae. Next, cut three 3-inch pieces of black stems for each ant. Have your child help you thread all three though the spring hole in each clothespin and adjust to form the legs. Glue the face and two more black buttons to the top of each clothespin. Then use the clips to secure your tablecloth, and enjoy a carefree meal in the summer sun.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
Although a mobile tool, it is recommended to set the compound miter saw in place with extended tables on both ends. This saw makes very quick and accurate cuts, allowing for compound cuts.  In addition to the rotating table, the compound milter saw has a rotating vertical pivot which lets the cutter head and blade to be tilted sideways, allowing both vertical and horizontal cuts to be angled on both planes.
Bruce Lamo has done woodworking pretty much all his life, although never exclusively to make a living. He prefers making furniture and working with solid wood, but often uses plywood when making cabinets. This article originated when a few friends were considering buying tools that based on his experience, he thought would not be a good investment.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.

Welcome to my beginner’s guide for getting started in traditional woodworking! Traditional woodworking with hand tools is my great passion and the passion of millions of people around the world. However, it can be very confusing trying to learn traditional woodworking if you don’t have the right resources. So I’ve worked hard to create the most simple and understandable resource on traditional woodworking to help people just like you.
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt.  Unfortunately, that ended up with the guy we hired stealing from us…..uggggh.  When will we ever learn to not be so trusting?!  Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!!  Sad.  Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.

Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
×