An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.

For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.

We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!


WoodSkills and Norman Pirollo offer online woodworking classes, woodworking plans, video lectures and woodworking tutorials. The classes and courses provide detailed and comprehensive step by step sequences for woodworking skill-building. Each woodworking class and tutorial is based on actual furniture making expertise. As founder of  White Mountain Design , Refined Edge Design , WoodSkills and Pirollo Design, I bring to you two decades of knowledge in furniture making. In recent years, I have authored three woodworking books:
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
Basic woodworking tools are different from beginner woodworking tools. For one thing, I don’t like to use the word “beginner” unless I am using it accurately. It’s not a very useful label, in my opinion, because it implies that there are clear-cut and hierarchical steps in your growth as a woodworker. Who wants to return to grade school during his or her valuable shop time? So I only use the word “beginner” when I’m talking about someone who is touching woodworking tools for the first time.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
To give you an idea about the different bookshelf plans available,this guide presents you 17 simple but alluring bookcase designs to choose from. The designs are not only in a wide array of sizes and styles but they are also inexpensive to build and will fulfil your home space. So be sure to go through all of them to find the best one for your room.

10.  While manufacturing the furniture, another important thing besides the precise parts manufacture is the assemblage. The pieces, when fitted, should come together easily, and not require to be twisted, sprung or bent in order to put the piece article together. It is the practice with skilled cabinet maker to put a piece of furniture completely together once (without glue, screws or nails)to see that everything fits right, before putting together permanently. After fitting the parts of a piece of furniture and before gluing, smooth such parts as cannot readily be smoothed after putting together permanently.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
For large outdoor gatherings, copious seating is a necessity. This outdoor couch can fit several adults, and oversized arm rests act as end tables for drinks. Before getting started, you’ll want to pick up the cushions for the couch first; depending on their size, you can make any adjustments to the cut list necessary for the perfect fit. Once you have the cushions, all the materials you need can be found at local home centers. We used treated lumber, but you can splurge for a naturally rot-resistant wood like cedar or cypress. We’ve got the full plans here.
Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
9.  Hand tools and machines: In our furniture plans, you will find only dimensions of the furniture and directions for their construction; we do not suggest manufacture techniques. We recommend that you decide for yourself how you will make particular parts of the furniture – based on your experience, skills in specific techniques and operations and depending on the machines and tools that you got.

Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Your first backsaws should be (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. You could certainly get by with just a larger dovetail saw and a carcass saw at first, if you don’t plan on immediately cutting large tenons. Buying backsaws can be very confusing because there is no standardized naming system, and a dovetail saw can be turned into a carcass saw (and vice-a-versa) by sharpening it differently. And practically everybody that’s selling antique saws mixes the names up. My buyer’s guide really clears this confusion up and will help you know what to look for.

A jointer makes the dges of your material smooth, straight, and square. This creates what’s commonly called a reference edge that you need for additional steps like ripping or crosscutting. In addition to perfecting the edges of your stock you can also straighten faces, called face jointing. Like edges, you’ll end up with faces that are nice and smooth, and dead flat; a precursor to other machining steps.
The old saying "If only I knew then what I know now" certainly applies to buying woodworking tools . Like nearly every woodworker, I would love a large shop equipped with all the best tools. Like most woodworkers however, I have had to make choices due to finances, space, and what was available at the time of need. As I look back at the purchases I made over the last 30 years, I have few true regrets, but there are many things I would do differently. Here is how I would approach equipment selection today.
Even though I have many large power tools I am still a fan of hand tools, in particular, planes and chisels. In many applications I have found they are the fastest means to an end. Other factors in their favor are their cost. Good hands tools are not cheap, but compared to their motorized counterparts, they are usually much less costly. Another is space. Besides taking up far less space in the shop, they often require less space to use. Think of edge joining an 8 foot long plank. On a jointer you need a minimum of 16 feet of work space. With a hand plane, you move the tool, not the material, so you only need slightly more room than the length of the material.
Kids love to watch grown-ups use woodworking tools, but what they love even more is making the sawdust fly themselves. With minimal equipment and adult help, your child will soon be turning out a wonderful variety of toys, games, gifts, household objects, and holiday decorations. These 50 easy and inexpensive projects are arranged by age and skill level.
Woodturning is the craft of using the wood lathe with hand-held tools to cut a shape that is symmetrical around the axis of rotation. Like the potter's wheel, the wood lathe is a simple mechanism which can generate a variety of forms. The operator is known as a turner, and the skills needed to use the tools were traditionally known as turnery. In pre-industrial England, these skills were sufficiently difficult to be known as 'the misterie' of the turners guild. The skills to use the tools by hand, without a fixed point of contact with the wood, distinguish woodturning and the wood lathe from the machinists lathe, or metal-working lathe.
Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.
This bookcase plan is designed to be large enough to handle all of the books belonging to the voracious reader in your family, virtually indestructible to withstand years of abuse, and easy on the pocket book using inexpensive materials from your local home center. For about $100 you can have a bookcase that would cost $600 – $800 at a retail furniture store.
Storage can never be enough for a home with children. Especially if the family is midsized to a large one! A headboard with optimum storage space is an ideal solution in children’s room to accommodate most of their belongings, so that they can have an easy access to them on a daily basis, and not litter them everywhere. The headboard can be revamped for them, according to their choice of colors and need.

WoodSkills and Norman Pirollo offer online woodworking classes, woodworking plans, video lectures and woodworking tutorials. The classes and courses provide detailed and comprehensive step by step sequences for woodworking skill-building. Each woodworking class and tutorial is based on actual furniture making expertise. As founder of  White Mountain Design , Refined Edge Design , WoodSkills and Pirollo Design, I bring to you two decades of knowledge in furniture making. In recent years, I have authored three woodworking books:


Capitalize on low hanging fruit to identify a ballpark value added activity to beta test. Override the digital divide with additional clickthroughs from DevOps. Nanotechnology immersion along the information highway will close the loop on focusing solely on the bottom line.Podcasting operational change management inside of workflows to establish a framework. Taking seamless key performance indicators offline to maximise the long tail. Keeping your eye on the ball while performing a deep dive on the start-up mentality to derive convergence on cross-platform integration. 

TheArtofHomeRenovations.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, TheArtofHomeRenovations.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.

For large outdoor gatherings, copious seating is a necessity. This outdoor couch can fit several adults, and oversized arm rests act as end tables for drinks. Before getting started, you’ll want to pick up the cushions for the couch first; depending on their size, you can make any adjustments to the cut list necessary for the perfect fit. Once you have the cushions, all the materials you need can be found at local home centers. We used treated lumber, but you can splurge for a naturally rot-resistant wood like cedar or cypress. We’ve got the full plans here.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.
Then, beginning several decades ago, shop classes began to be removed from secondary curriculums. With the decrease in educational funding, and increasing emphasis on standardized testing, schools began to cull electives, institute stricter graduation requirements, and focus more on college prep academics and the subjects necessary for passing state exams. There wasn’t money or time to maintain tools and sawdust-filled workshops, and one by one school districts dropped their shop classes, figuring that students who wished to pursue trade skills could do so later at a vocational college.

Formally known as a “tilting arbor saw,” this tool is just an upside-down electric handsaw that’s been mounted to the underside of a steel table top, with the circular saw blade protruding through a slot. The “arbor” is the shaft on which the blade spins. It’s an axle that can be tilted with respect to the horizontal table top for cutting angles; it’s raised or lowered to adjust cutting depth. A miter gauge enables the sawyer to push stock at angles or perpendicular to the blade (“cross-cutting”). A fence can be fixed parallel to the blade for cutting along the length of a workpiece (“rip-sawing”).
In being self-employed, one day will greatly vary from the next, but generally, I start in the morning by dealing with in-town errands or head right to the shop if there are none. Once at the shop, there’s an e-mail check, then a brief glance at various websites to look for new developments related to our market and clientele. Then the real workday starts. I’ve got a bunch of notes regarding current projects taped next to my computer and will make a list for the day’s tasks by picking the highest priority items from the notes. The goal is to get that stuff accomplished by the end of the day. There are two of us in the shop, but we usually work on separate projects, so that’s why I have my own to-do list. Some days are spent on the computer designing or creating programs for the laser or CNC. Other times we’re doing runs of sunglasses or guitar parts which we sell wholesale to other businesses. In which case, I may be operating the laser or CNC. Despite the high-tech tooling, there’s still a lot of bench work to do, and that can involve cutting and fitting joints with chisels and hand planes. Besides that, there’s always plenty of rough lumber to mill since no project can begin until boards are flattened, surfaced and cut to dimension.

Today, in our age of plastic and factories, woodworking has transformed from a common necessary skill into something almost mysterious or awe-inspiring. Because most 21st-century consumers are used to driving to big box stores to pick up another mass-produced replacement when their desk falls apart or their chair breaks, any man today that can walk up to a lumber pile with saw and plane to shape a beautiful and enduring replacement is revered as a “true craftsman.”


This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
Tightening the nuts clamps the uprights against the shelves, holding them in place and providing shear strength (through friction) for the whole assembly. I know of an 8' tall, 12' long version of these shelves that has survived a few minor earthquakes while fully loaded with hundreds of books. Once the nuts are tightened on my smaller versions, I (all 240lbs of me) have a very hard time "racking" the shelves by pushing on one end of them in an attempt to get them to collapse: I can't.

Table saws, band saws, and radial-arm saws are examples of woodworking machines that are most often used exclusively in a wood shop because they are far too large and cumbersome to be portable. Even though they're confined to the shop, these workhorses are so useful that it makes sense to complete a woodworking project in the shop and carry the finished piece to the location or job site where it will be used or installed.

A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.


One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project. 

Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.
Make It: Have your child paint 10 craft sticks and allow them to dry. Put a line of glue on the back of five sticks. Sandwich a piece of string between a glued stick and an unglued stick; clip them with clothespins to hold the glue securely. Let dry. Run glue along an unpainted craft stick, lay it horizontally and stick on the five strings as shown (don't let the sticks hang too low or they'll tangle in the wind). Top with another unpainted stick and add clothespins to hold the glue securely. Once dry, tie the strings together and cut off the excess. Hang outdoors and let the wind do its work.
My basic advice is to develop lots of connections with people. Most branches of woodworking are hard to sell without knowing the right people – especially when targeting the luxury furnishings or corporate markets. I started down this path with the idea that I might own my own shop but forgot about that once I’d accepted employment in the field. Since I was satisfied working for others, I didn’t bother making the connections, and now I’m so busy it’s hard to get away from the shop long enough to do so. That’s not the end of the world, as we’re still pulling in plenty of work. It just took longer to get there than it should have. For those considering a self-employed woodworking career, it’s a good idea to meet individuals who associate with the types of people that are likely to become future clients. Word-of-mouth is still a powerful form of marketing even in this age of internet.
Just for the record, a jointer and planer are not from the ICDT kit – the philosophy on that column is, indeed, beginner AND basic (hence the Workmate). The tools we suggest in the ICDT manual are for those who are working at a kitchen table or in a backyard; the tools the editors would recommend for someone who is quite sure he or she wants to pursue serious furniture making would be rather different.
Despite the popularity of plastics, MDF (medium density fiberboard) and other materials, wood is still the product of choice for most people when it comes to the expectation of quality, value, and utility.  Today, many wood products, such as musical instruments and furniture are mass-produced, but trained woodworkers make custom-made products with their hands and their tools based on drawings and architectural designs.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
I am from pittsburgh and I make a lot of my projects out of pallets from blanket chest to nautical lamp post and they both sell well here wine racks are Good sellers in the fall and winter months bird houses in the spring it seems what’s the best time of year and the rite product to build I lucked out and I am busy all the time and I can’t forget my best seller is a Raised doggie feeder and water tray with a bone I cut out and it hangs on the front of the tray with 2 small chains and can be personalized with the pets name on it I love to up cycle wood and keep on building
Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.
I use chisels perhaps more than any other tool in my workshop, so it’s a good idea to not cheap out here. A high quality set of bevel edge bench chisels (new or vintage) will last you many years (likely  your entire life) and will be used on nearly every project. I’ve used some descent affordable plastic handle bench chisels, but highly prefer lighter wooden handle chisels with excellent steel.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.

But until then, I’ve been thinking of other ways to use my hands and create things.  (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY.  In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine!  (Any out of town-ers want to fly in?! ;) )
Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
Although this universal admiration of hand skill is appreciated, the truth is, woodworking is no mystery. And fortunately, even if you missed out on taking a thorough shop class in high school and feel ill-equipped to tackle a simple woodworking project, it’s definitely not too late to learn. Here’s a list of some basic skills you would do well to develop. None of these skills require expensive, dangerous machinery or exotic tools. They are the foundational skills every woodworker should know.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
Make It: Paint four clothespins black. Thread a 4-inch-long black chenille stems through the two holes of a large black button. Twist and curl the ends of chenille stems where they meet to form antennae. Glue googly eyes just below the antennae. Next, cut three 3-inch pieces of black stems for each ant. Have your child help you thread all three though the spring hole in each clothespin and adjust to form the legs. Glue the face and two more black buttons to the top of each clothespin. Then use the clips to secure your tablecloth, and enjoy a carefree meal in the summer sun.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick. 

For large outdoor gatherings, copious seating is a necessity. This outdoor couch can fit several adults, and oversized arm rests act as end tables for drinks. Before getting started, you’ll want to pick up the cushions for the couch first; depending on their size, you can make any adjustments to the cut list necessary for the perfect fit. Once you have the cushions, all the materials you need can be found at local home centers. We used treated lumber, but you can splurge for a naturally rot-resistant wood like cedar or cypress. We’ve got the full plans here.

Click HERE or on the image below for the downloadable Double Chair Bench Plans. These plans are 100% free and you have the option to donate at the time of download to help support DIY PETE so he can devote more time in creating FREE video tutorials and plans for you. This is 100% optional of course! If you’d like them for FREE simply enter “0” in the dollar amount   Cheers! – Pete

Too many people have perpetuated the myth that working wood by hand is really hard work, simply because they were using a dull tool. It is an axiom among woodworkers that in order for things to go smoothly, you have to “let the tool do the work.” If your saw requires a good amount of push to cut or if you find you need a running start to make shavings with your hand plane, you aren’t doing yourself any favors. Sharpening your tools is a basic and foundational skill because it is something that needs to happen regularly. Not only is it inefficient to work with dull tools, it’s dangerous. If you feel like you need to push your chisel with body weight to complete the cut, when it does pop free, you will lose control and your tool will stab into whatever is in its path. Learn how to sharpen your tools and you will find woodworking to be enjoyable, safe, and efficient.

As for schooling, many local school districts, community colleges and woodworking stores offer woodworking classes, but those are a mixed bag. A handful is really good and many are terrible. There’s also a big difference between woodworking for fun and doing it for a living, and most classes are geared towards hobbyists. Out of all the proper woodworking schools with good reputations, I’ve only had personal experience with Marc Adams School of Woodworking. That place I recommend 100%, as the instructors are generally active professionals in their specialized niches, so one can always pick their brains for extra information related to earning a living. The director of the school also does a good job of screening instructors to eliminate the ones that don’t interact well in a classroom setting.
×