I am from pittsburgh and I make a lot of my projects out of pallets from blanket chest to nautical lamp post and they both sell well here wine racks are Good sellers in the fall and winter months bird houses in the spring it seems what’s the best time of year and the rite product to build I lucked out and I am busy all the time and I can’t forget my best seller is a Raised doggie feeder and water tray with a bone I cut out and it hangs on the front of the tray with 2 small chains and can be personalized with the pets name on it I love to up cycle wood and keep on building
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Glue up a panel using the same material as your face frame. I generally size the top so that it overhangs by about 1″ on all sides, which means a 38-1/2″ x 13-1/4″ panel. Trim to size using a panel cutting jig. An alternative approach to building the top is to use a piece of 3/4″ plywood (same material you used for the sides and shelves), with wood strips applied to each edge as edge banding to mask the laminations, using the same approach as you used to edge band the shelves.
I am from pittsburgh and I make a lot of my projects out of pallets from blanket chest to nautical lamp post and they both sell well here wine racks are Good sellers in the fall and winter months bird houses in the spring it seems what’s the best time of year and the rite product to build I lucked out and I am busy all the time and I can’t forget my best seller is a Raised doggie feeder and water tray with a bone I cut out and it hangs on the front of the tray with 2 small chains and can be personalized with the pets name on it I love to up cycle wood and keep on building
Thank you for sharing your story! Would love to hear how you got started with your blog and business too someday, I always find it so interesting what inspires people to shift their career path. I can’t believe you’ve learned so much with YouTube videos! And congrats on creating such a successful business from scratch and also having the courage to walk away when you knew it wasn’t for you anymore. We’re having a home built next year, so look forward to checking out all the custom work you’ve done with your place!
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Today, in our age of plastic and factories, woodworking has transformed from a common necessary skill into something almost mysterious or awe-inspiring. Because most 21st-century consumers are used to driving to big box stores to pick up another mass-produced replacement when their desk falls apart or their chair breaks, any man today that can walk up to a lumber pile with saw and plane to shape a beautiful and enduring replacement is revered as a “true craftsman.”
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.

Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
I learned the basics from J. Arthur Johnson when I was in 7th grade shop class . . . and I’ve been self-taught ever since. I do read Fine Woodworking (I have EVERY issue) and some books that my wife and friends have given me; and of COURSE Marc’s fine blog and a few other on-line sources but I don’t feel like I have really learned how to do anything until I’ve tried and failed and then re- and re-re-tried until I’ve made it work MY way.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.

The circular saw is a hand held or table mounted saw. Circular saws come with the ability to set the depth of the blade, which enables one to create cut offs, dados and narrow slots. There are upsides and downsides to all saws, and the one down side to the circular saw that its light weight sometimes causes it to move when cutting, and stability in the machine is important for the cut and for safety. On the other hand, this is also its advantage. The versatility and the mobility of this saw gives one the freedom to work anywhere.
Teds Woodworking is a big collection of woodworking plans and all of these are well organized and categorized so that you find what you are looking for fast. These woodworking plans include bed plans, table and chair plans, furniture plans, shed plans, bird house plans and many more. Each of these woodworking plans come with full comprehensive instructions as well as diagrams. You will be able to see, what it is you want to do. The program also includes 150 training videos, so you can see and learn how things should be done. You will be able to see the complete pieces that you need to build and learn how to fit them together. The diagrams are used by many individuals as they go through each part of the process.
Small planers on the other hand can do a lot for you. Here it is hard to argue with their capabilities. A large industrial-weight planer is a machine few small shops can justify, but there are numerous portable planers available for a few hundred dollars that can deliver a reasonable cut. They allow you to quickly clean up glue joints or prepare rough lumber.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
oh yeah, and buying a bunch of cap nuts is not so easy unless you order ahead of time. i went to two hardware stores (one family owned and one big box) and they kind of laughed at me when i said i needed 32. so i got regular nuts, tightened them so they were flush with the all thread on the front side, hammered it against the board and tightened the back side while holding the front one in place with a wrench. so, some of them have a little bit of overhang on the back side, but i don't have to worry about gouging skin while walking past it. for my next set, i'll order the cap nuts in bulk from ebay ahead of time...

We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
×