The knotty pine bookcase parts are all standard dimensional lumber that you can find at any home center. We joined the shelves and legs with biscuits. If you don’t own a biscuit joiner but still want to build this project, you can simply nail or screw the parts together and fill the holes. We used a table saw to cut the 1-1/2-in. square legs from 2x4s and a router with a 45-degree chamfer bit to bevel the edge of the top. If you don’t have a table saw or router, you can just use stock 2x2s for the legs and leave the edge of the top square.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.

Each bookcase door has a fixed middle shelf and four adjustable shelves. The doors are available in hardwood veneers, MDF or vinyl-lam. Bookcase sizes range from 36in. to 66in.wide and up to 96in. high. Order them directly from the manufacturer. The system, weighing 400 lbs., will show up on a single pallet. Prices start at $2,200 (plus shipping) for the entire system.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.

In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.
Click HERE or on the image below for the downloadable Double Chair Bench Plans. These plans are 100% free and you have the option to donate at the time of download to help support DIY PETE so he can devote more time in creating FREE video tutorials and plans for you. This is 100% optional of course! If you’d like them for FREE simply enter “0” in the dollar amount   Cheers! – Pete
It’s a unique environment to learn in, and a great neighborhood to visit with a spouse or entire family. Just a quarter mile from the beginning of Tampa’s Riverwalk, you’re steps away from Tampa’s museums, parks and some of the hippest spots to eat and drink. In fact, the School of Woodwork partners with a craft beer business just around the corner.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Make It: Paint nine craft sticks red, six craft sticks white, and four mini craft sticks white. Let them dry. On a rectangle piece of cardstock, have your child create a blue sky and green grass with colored paper or markers. Then help her create the bottom of the barn by gluing on a row of 11 craft sticks vertically in the following pattern: two red, one white, five red, one white, two red. Glue white sticks horizontally along the top and bottom and cross two in the middle as shown. Glue the mini craft sticks to red cardstock to form the barn roof. Adhere the barn roof to the background above the barn. Cut out a rectangle from black paper and adhere it to the barn. Cut strips from a paper bag and crumple for the look of hay; adhere to black rectangle.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!

A mechanical reasoning or aptitude is also essential, mainly because woodworkers work with such a variety of machines and tools.  A tool in the hands of an untrained or inexperienced woodworker is a recipe for disaster. Woodworkers should understand and be able to apply mechanical principles to solve any problems they may encounter. Critical thinking skills are important too as woodworkers may face unexpected problems that need to be handled quickly. In this way, woodworkers can use reasoning and logic to foresee any potential problems, and develop solutions before mishaps happen.
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!​
In recent years, this versatile and accurate tool has become a fixture in the work shop and at the work site. Also called a “chop box,” the miter saw consists of a powerful circular saw mounted on an arm that hinges at the rear of the tool. When the blade is lowered in a chopping motion, it cuts through the workpiece, passing through a slot in the base. The motor and blade can be pivoted with respect to the base for miter cuts. Another adjustment makes it possible to tilt the blade, too, allowing for compound miter cuts, handy for jobs like cutting crown moldings, which are set at a pitched angle and that must also turn around corners. The diameter of the blade determines the maximum cut width, with standard sizes ranging from 8-inch blades up to 15 inches. A 10- or 12-inch saw is sufficient for most jobs.
And with many homes falling into the “contemporary but traditional’ style that has taken over the decade, these wine racks are in high demand and can fetch a pretty penny for even a more simplistic design.Feel free to get creative with the design for some more bargaining power. And for a design to hold a small number of bottles, you can expect up to $50 per unit sold.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.
TheArtofHomeRenovations.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, TheArtofHomeRenovations.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Once you’ve mastered the basics, then check out magazines like Fine Woodworking, Woodcraft, etc. Visit your local woodworking store (like Woodcraft or Rockler) and browse the book / plans section. What I like is these stores normally have people with woodworking expertise and can answer most of your questions whether they be basic or advanced. They also offer monthly workshops at an affordable price.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
I also had the brainstorm to use two nail-in furniture "feet" on the bottom of each 2x4 on the front side so as to compensate for the carpet tack strip on the back edge and to make the shelves lean ever so slightly into the wall. I thought we might have to anchor the top of it to the wall, but with the feet, it stands very firm with absolutely no signs of wanting to tip forward! I felt great satisfaction when the almost 150 square inches of friction applied allowed for NO racking -- I could practically climb the end without anything budging! 

Table saws, band saws, and radial-arm saws are examples of woodworking machines that are most often used exclusively in a wood shop because they are far too large and cumbersome to be portable. Even though they're confined to the shop, these workhorses are so useful that it makes sense to complete a woodworking project in the shop and carry the finished piece to the location or job site where it will be used or installed.
A jointer makes the dges of your material smooth, straight, and square. This creates what’s commonly called a reference edge that you need for additional steps like ripping or crosscutting. In addition to perfecting the edges of your stock you can also straighten faces, called face jointing. Like edges, you’ll end up with faces that are nice and smooth, and dead flat; a precursor to other machining steps.

WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
For cross-cut work, position the board flush with the fence at the rear of saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles; set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitering, or even turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. Many models use 10-inch blades, which will cut stock up to 3 inches thick.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.
I am from pittsburgh and I make a lot of my projects out of pallets from blanket chest to nautical lamp post and they both sell well here wine racks are Good sellers in the fall and winter months bird houses in the spring it seems what’s the best time of year and the rite product to build I lucked out and I am busy all the time and I can’t forget my best seller is a Raised doggie feeder and water tray with a bone I cut out and it hangs on the front of the tray with 2 small chains and can be personalized with the pets name on it I love to up cycle wood and keep on building

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.


​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.

To minimize potential cupping, we decided to make the top by gluing two pieces of 1×6 together rather than using a solid board. Choose a straight piece of 1×6 with a sharp, clean edge. Cut the pieces long and trim the top to length after you glue the two parts together. For pro tips on gluing boards edge-to-edge, see “Edge Gluing Boards” . Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps. Glue and clamp the two 1x6s. Then let the glue set up about 30 minutes before routing the edge (Photo 10).


Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Manufacturing the furniture is one of the most complex crafts, because manufacturing the good quality furniture requires a lot of skills, tools and rich experience. As the part of interior, the furniture is always on the visible place and it is often the main element of interior decorations. Because of this, its manufacture does not allow any mistakes. Just a tiny error on a visible place can often ruin all the effort that was made to produce that piece of the furniture. Because of that, a quality furniture plan is one of the basic things for reducing the risk of errors.

About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
Capitalize on low hanging fruit to identify a ballpark value added activity to beta test. Override the digital divide with additional clickthroughs from DevOps. Nanotechnology immersion along the information highway will close the loop on focusing solely on the bottom line.Podcasting operational change management inside of workflows to establish a framework. Taking seamless key performance indicators offline to maximise the long tail. Keeping your eye on the ball while performing a deep dive on the start-up mentality to derive convergence on cross-platform integration.
Next, grab a role of tape to make your rounded corners for the arms and back supports. Do a rounded corner for the two outside armrests, and for both outside pieces of the table top. Create rounded corners for the top of the backrest supports as well(Part H). Cut with a jigsaw and use an orbital sander to smooth the edges. Check out photos in later parts of the project to see the rounded edges.
Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)
Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood.

As shown in the video, attach the front and rear leg together on the top with the arm support 2×4. Measure 11″ back from the rear of the front leg and put a mark. Then line up the rear leg so that the 15 degree angle sits flush with the arm support. Attach with 2 1/2″ Deck Screws. Use the star (torx) deck screws instead of philips because they are much easier to use and don't strip. Only attach the two legs to the arm support in this step. We'll get to the lower cross support later.  Measure 11 inches from the back of the front leg to the front of the back leg. Flush it up with the horizontal 2×4 and attach with 3 screws.   Here is another look at how the sides will look when completed.
The wood to be turned is fixed between the “headstock” and “tailstock” of the lathe. The headstock houses the motor that spins the workpiece; the tailstock is adjustable, moving along the length of the bed to fit workpieces of various lengths. Once the piece is locked in place, the tool rest is positioned about an eighth of an inch away from the piece, just below its center line. The spinning workpiece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in which the workpiece is fastened with screws to the face plate of the drive spindle, enables the woodworker to produce bowls and other hollow goods.

You can create a beautiful coffee table by simple stacking logs together. Line the logs end up and create a circle whatever size you need. Then just tie them all together with rope or twine to keep your coffee table secure. You do need to make sure that the logs are the same height and you may want to sand the tops down just a bit to make them smooth.
Glue up a panel using the same material as your face frame. I generally size the top so that it overhangs by about 1″ on all sides, which means a 38-1/2″ x 13-1/4″ panel. Trim to size using a panel cutting jig. An alternative approach to building the top is to use a piece of 3/4″ plywood (same material you used for the sides and shelves), with wood strips applied to each edge as edge banding to mask the laminations, using the same approach as you used to edge band the shelves.
[…] Technically this is not a DIY video; it goes by very fast and there are no narrated instructions. That is because it was put together to promote a finished product available here dfmmc.com. But if you have experience welding, it is not all that hard to follow along and figure out the steps and write them down. I might get lazy and buy one … but I love making things, so I definitely will be giving it a try. Whether you buy one ready-made or weld your own, I hope you love this rack as much as I do. What an awesome discovery! If you love rustic decorating you must check out our 85 Rustic storage projects and 40 Rustic home decorating ideas. […]
Glue up a panel using the same material as your face frame. I generally size the top so that it overhangs by about 1″ on all sides, which means a 38-1/2″ x 13-1/4″ panel. Trim to size using a panel cutting jig. An alternative approach to building the top is to use a piece of 3/4″ plywood (same material you used for the sides and shelves), with wood strips applied to each edge as edge banding to mask the laminations, using the same approach as you used to edge band the shelves.
No need to mark the location of biscuits on the shelves and sides. Instead make marks on the scrap of wood used as a fence. Draw marks to indicate the outside edges of the 1×8 shelves and sides, and mark 1-3/4 in. in from each edge to indicate the center of the biscuits. To use the fence, line up the outside marks with the edges of the part you’re cutting slots in. And then line up the center mark on the biscuit-joining tool with the marks for the center of the biscuits (Photos 3 and 4).
I also had the brainstorm to use two nail-in furniture "feet" on the bottom of each 2x4 on the front side so as to compensate for the carpet tack strip on the back edge and to make the shelves lean ever so slightly into the wall. I thought we might have to anchor the top of it to the wall, but with the feet, it stands very firm with absolutely no signs of wanting to tip forward! I felt great satisfaction when the almost 150 square inches of friction applied allowed for NO racking -- I could practically climb the end without anything budging!
Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.

I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.


Just for the record, a jointer and planer are not from the ICDT kit – the philosophy on that column is, indeed, beginner AND basic (hence the Workmate). The tools we suggest in the ICDT manual are for those who are working at a kitchen table or in a backyard; the tools the editors would recommend for someone who is quite sure he or she wants to pursue serious furniture making would be rather different.
But before you purchase clamps, build your first project and put it together without glue. Then see how many clamps you think you will need to put enough pressure in all the right spots. Then proceed to purchase that number of clamps. Repeat this process on your next project, and purchase more clamps if needed. See my buying guide for different clamp types, uses, and my favorite brands.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
Since money and space are usually in high demand, you want your purchases to make sense and work for you as far into the future as possible. To do this, the focus should be how to expand your capabilities rather than getting one project done quickly. With this in mind, and based on what I've learned over the past three decades, here's how I would proceed if I were starting over now. 
×