In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Hi, Patrick. In a space constrained scenario, a good track saw can enable you to do some very high quality work, and you can perform many of the tasks that are commonly performed on a table saw. You could definitely build closets, vanities, and a great variety of other comparable projects with a good track saw. The advantages that a table saw can bring are efficiency, repeatability with a single fence setup, and support for a dado blade. If you get a larger shop space someday and decide to add a table saw, you’ll still get plenty of use out of your track saw. Even though I have a large cabinet saw I still use a circular saw and guide for a lot of cuts on sheet goods, mainly because a 4×8 sheet can be unwieldy to handle on a table saw.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
I really like building difficult cabinets, laying them out, and assembling them. It really gives me a challenge to build something better each time, but the sanding and clean up are not my favorite aspects of this work; you better get used to it. And I wish I would have taken some business classes because the part of running a business is another element added to cabinet making.
Make It: Have your child paint 10 craft sticks and allow them to dry. Put a line of glue on the back of five sticks. Sandwich a piece of string between a glued stick and an unglued stick; clip them with clothespins to hold the glue securely. Let dry. Run glue along an unpainted craft stick, lay it horizontally and stick on the five strings as shown (don't let the sticks hang too low or they'll tangle in the wind). Top with another unpainted stick and add clothespins to hold the glue securely. Once dry, tie the strings together and cut off the excess. Hang outdoors and let the wind do its work.
Arguably the industrial arts class that is most missed is wood shop. Learning how to work with wood is not only handy, allowing you to make and fix things around the house, but allows you to satisfyingly connect with a long history of craftsmanship. Woodworking was one of the earliest skills mankind developed; the pre-industrial world was largely made of wood, and for thousands of years, all men had at least a rudimentary understanding of how to shape and manipulate it. Even up until the second half of the last century, tradesmen and professionals alike had the confidence to be able to build wooden shelves, cabinets, or even chairs for their family.
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
One simple method of getting your foot in the door is to check out Craigslist help-wanted ads. It’s about the only place I’ve seen a decent selection of job postings for woodworking, and some are entry-level positions. Once a little experience with basic tools is acquired, more options open up. However, a lot of the most interesting positions can’t be found by searching jobs postings. Many high-end furniture shops recruit via networking instead of advertising for help. To break into the custom furnishings market, do research to find out who is doing the sort of work you’d like to get into, then figure out what circles they participate in. If they belong to a particular artist association, try to attend their shows or get an introduction to one of the members. If they teach classes, attend their classes. The goal is to get their attention, and let it be known you wish to pursue a woodworking career. Demonstrate good work ethic, reliability and a willingness to learn, and someone might take notice. Talk to people and continue to introduce yourself to others.

Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.

As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.

Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.
Do you often get intimidated by woodworking? With all the tools available, the problem here is that many don’t know what wood power tools to use. Woodworking has a variety of specialized tools for different tasks. Knowing which ones to pick is important to make woodworking easy and enjoyable. If you have no idea about power tools, this will definitely help you out.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.

Dust Collector. A dust collector works at the source of creation. It’s main purpose is to collect the dust right from the place you are cutting the wood. A lot of power tools come with a dust collector extension which allows the dust collector to be attached to them directly. This means a lot less cleaning up for you to do. Dust collectors come in two types, single bag and double bag. Single bag ones are more common.
×