The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close

This demise of shop classes is quite unfortunate, as they were never solely about preparing students for trade employment. Rather, they taught all men manual skills that they could use and enjoy throughout their lives, whether they became a carpenter or a doctor. They were considered part of becoming a well-rounded man – one able to use both his hands and his mind.
Learn the basics of woodworking with simple hands-on projects to build your confidence and skills. Each lesson in this class explores an area of woodworking that will form the building blocks of all future woodworking projects you undertake. Keeping the average DIY'er in mind, this entire class is conducted using basic handheld power tools, with no fancy fixed tools like table saws, lathes, planers, or drill presses.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
Rip the 3/4-in. plywood to width for the case sides and shelves using a table saw or circular saw and straightedge guide. Crosscut the case sides to length, making them 2 in. shorter than the distance from the top of the base to the ceiling. Then, cut all the shelves to length. The shelves should be no longer than 36 in. to keep them from sagging under heavy loads. Before proceeding, finish all the plywood pieces.
One great aspect of Teds Woodworking is that it is easy to understand! You will find all the projects and a way to learn how to build them with an easy step by step procedure. These plans and structures are already proven to work. Some guides out there will only give you lousy plans and waste your time. Teds Woodworking offers simple guides and schematics. This system has blueprints for almost everything you want to make. There are available blueprints from dog houses to green houses. Even instructions for building gazebos and guitars are easy to follow. The instructions on how to create children’s and baby cradles are carefully laid out in a way that you can easily build them right away.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Vacuum cleaner. A wet and dry model is preferred. Dust collection is very important from the aspect of your safety and health while working in the wood shop. If you are working in an enclosed space, dust collection and removal is a must. While we recommend getting a dust collector, you can start with a good wet and dry vacuum cleaner. It will help you keep your work area clean while working on a project , as well as clean up the place at the end of the day.
Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.

The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close


Basic woodworking tools are different from beginner woodworking tools. For one thing, I don’t like to use the word “beginner” unless I am using it accurately. It’s not a very useful label, in my opinion, because it implies that there are clear-cut and hierarchical steps in your growth as a woodworker. Who wants to return to grade school during his or her valuable shop time? So I only use the word “beginner” when I’m talking about someone who is touching woodworking tools for the first time.
The content of this website, TheArtofHomeRenovations.com, and its associated social media pages, is provided for informational purposes only. The information is not intended as, nor should it be considered a substitute for professional claims, suggestions, diagnosis, or counseling of any kind under any circumstances. By reading this website, you acknowledge that you are responsible for your own decisions. Do not take information from any website, including this one, and try it without proper research and supervision. For more information, please read our Privacy Policy.
My whole life, I’ve loved to be creative and make things. Once I got older though, creativity and anything art related really got pushed aside for a more serious career path. After graduating from college, I decided to go to grad school, get my MS in accounting, and then I became a CPA (Certified Public Accountant), and started working in accounting for several years. 
×