To be honest, I loved almost all the 40 bookshelf ideas mentioned here. But I think some ideas like modular bookcases need some expertise, what do you say? Bookcases are something where we can really be creative. Loved the skateboard bookcase(I have never seen something like that, simple as well). You can also include DIY bookshelves with glassdoors(or like closed bookshelves). Triangle bookshelves, diamond bookshelves, U bookcases etc would be some additives to this list (very easy to build)
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
After investing a number of weekends building a nice table or chest, how are you going to finish it? Finishes beautify and protect the piece you’ve worked so hard to build so don’t cop out and do the “rub it with oil” thing. There are so many beautiful finishes that become second nature to work with. I use shellac 99% of the time. Once you get the feel down, it’s really quick to apply, very forgiving, easily repairable, and you never have to clean a brush (because it re-softens in alcohol)! There are other varnishes that provide good protection for outdoor use as well. I recommend picking up a good starter book, like Jeff Jewitt’s Hand Applied Finishes. It is simple and straightforward, without getting too far into minutiae.
A marking knife is used for marking where you will be cutting with your saws. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.
Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
One great aspect of Teds Woodworking is that it is easy to understand! You will find all the projects and a way to learn how to build them with an easy step by step procedure. These plans and structures are already proven to work. Some guides out there will only give you lousy plans and waste your time. Teds Woodworking offers simple guides and schematics. This system has blueprints for almost everything you want to make. There are available blueprints from dog houses to green houses. Even instructions for building gazebos and guitars are easy to follow. The instructions on how to create children’s and baby cradles are carefully laid out in a way that you can easily build them right away.
How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.
Hey Great Article,Thanks. 4 months ago, I started looking for woodworking.The industry is extremely interesting,but I have problems with how I can do it.My uncle who has been doing more than me in this industry,has suggested to me to follow Teds plans.Do you think it’s a good move to follow these plans??I keep reading good reviews about Teds plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.
It’s mostly been learn by doing for me. I can’t afford to go somewhere to take any lessons. However, I do learn from books, DVDs, and videos on the internet. I still believe that learning by doing is the best way. Books and videos can get you going in the right direction but when you do it on your own all kinds of problems crop up that you have to solve. For example, when woodcarving the best way to understand what carving with the grain is is to carve with a carving tool. Same thing about sharpening a carving tool. You had better learn how to sharpen by sharpening your tools when they need it. You’re dead in the water if your carving tools are not sharp.
Thinking about starting a crafts or DIY business? Take a look at these creative ideas using pallets, which have become very popular. One of the reasons many enjoy creating DIY ideas into DIY projects with pallets is there are so many different type of items and decorations that can be made from this rustic wood. Pallets are simply leftover wood and using them is a very eco-friendly and green thing to do. If you choose to make these crafts to sell, you’ll be pleased to discover that many pallet crafts can be created over a weekend. So give DIY pallet projects a try, there are so many here to enjoy! Happy Building and Selling!
1. The choice of wood: The choice of wood depends largely on the purpose which it is to be used and personal taste. We will recommend the type of wood in most cases, but since there are many wood types that fully satisfy the set quality standards for each piece of furniture, the final selection of wood type will depend on your taste, the accessibility on the market and the price. In the furniture manufacture you can use both hardwood and softwood, but if you want your piece of furniture to last for generations, we recommend a good quality hardwood. The quality of wood is one of the most important things that have to be considered when making furniture. A numerous wood types are being used for the furniture manufacture. Traditionally, the most frequently used is a good quality local hardwood, so – depending on which part of the world you are living in – you can usually found the furniture made out of maple, figured maple, cypress, redwood, walnut, cherry, mahogany, oak, birch (yellow, red, flame birch), beech, alder, aspen, elm, hickory, teak, pine and many other wood types. In the past, when demand for the furniture was not so big as it is today and when the furniture was made to last for generations, only the most hard and durable woods were used. Today, when the furniture is no longer made to last for a hundred years, it is often made out of the less durable woods, which are less expensive, and can endure for a long period with good care and maintenance in modern living conditions. Choose good quality and well dried wood with grain and color characteristics that you like, get to know its treatment characteristics and features and you will fulfill the first condition to own a beautiful piece of furniture.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
To be honest, I use to not know a thing about woodworking or power tools. In fact, I didn’t even know how to use a drill! And the thought of power tools and woodworking definitely sounded kind of intimidating and out of my league, like it was more of a rugged guy thing. I’m so glad those initial thoughts didn’t keep me from discovering one of my greatest passions.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
When many people hear the word woodworker, the image of someone leaning over a workbench sanding a long piece of wood with his or her hands. However, modern woodworking requires training on highly technical machinery, such as CNC (computerized numerical control) machines. Even woodworkers caught somewhere between modern equipment and a hand planer typically use CNC machines to fabricate large or intricate products. If working for a large company, a lot of the work will be done on an assembly line or in various areas on the floor designated to complete a particular part of a project. The tasks will be handled by different workers with very specialized training on each machine. For example, one machine might cut a large piece of wood into three sections, whereas another machine might take one of the sections and round each edge.
Bruce Lamo has done woodworking pretty much all his life, although never exclusively to make a living. He prefers making furniture and working with solid wood, but often uses plywood when making cabinets. This article originated when a few friends were considering buying tools that based on his experience, he thought would not be a good investment.
The old saying "If only I knew then what I know now" certainly applies to buying woodworking tools . Like nearly every woodworker, I would love a large shop equipped with all the best tools. Like most woodworkers however, I have had to make choices due to finances, space, and what was available at the time of need. As I look back at the purchases I made over the last 30 years, I have few true regrets, but there are many things I would do differently. Here is how I would approach equipment selection today.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.