Of course, there’s the occasional install, client meeting or photo-shoot, but those don’t happen often enough to be considered a typical day. I should mention that every day brings its share of phone conversations with clients and suppliers. That happens at all hours. Most work days end by 7:30pm, and once I’m home and have eaten supper, I’ll usually put another hour into handling whatever financial, legal or internet tasks are most pressing at the time. Altogether, a typical work day is about 12 hours, and this is 6 days a week. At 2 1/2 years old, the business is still a start-up which is the reason such long hours are necessary.
But until then, I’ve been thinking of other ways to use my hands and create things. (Even though many of our saws and tools have been stolen.) But I’m feeling a little antsy to make some quick projects, because creating makes me extremely happy…..so we’re calling this surge in me to create something simple, THERAPY. In fact, I need to call up a few friends and have them make some with me because friends and creating is a favorite combo of mine! (Any out of town-ers want to fly in?! ;) )
Dividers (or compass) are used for taking and repeating a measurement over and over again on a work piece. Traditional woodworkers rarely take measurements with a tape measure when doing fine joinery work, but rather take a measurement with dividers then transfer that arbitrary (yet accurate) measurement to another work piece. This removes a degree of inaccuracy.
oh yeah, and buying a bunch of cap nuts is not so easy unless you order ahead of time. i went to two hardware stores (one family owned and one big box) and they kind of laughed at me when i said i needed 32. so i got regular nuts, tightened them so they were flush with the all thread on the front side, hammered it against the board and tightened the back side while holding the front one in place with a wrench. so, some of them have a little bit of overhang on the back side, but i don't have to worry about gouging skin while walking past it. for my next set, i'll order the cap nuts in bulk from ebay ahead of time...
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
I learned about the trade from my father starting when I was 6 years old. I took woodshop courses in high school, and was granted the Industrial Arts Award my senior year. I also took some college courses in woodshop before I started my own business when I turned 19.My average work day is laying out jobs, cutting parts, designing the different jobs, and assembling the cabinets. I also am teaching my daughter how to build woodworking projects and cabinet parts, as well as helping with our cutting boards.
We now have over 58 linear feet of shelving (with space under for shoes) for that wall that barely protrudes 12.25" into the room for a total cost of about $125! We plan to make at least two more units to accommodate the more than 15,000 books we own that are currently on store bought or cobbled shelving and in boxes plus have display space for our many collections Our only problem...we didn't take into account the depth of the shelf itself -- if you've got 10" between holes, you actually only get 9 1/8" of useable height on the shelf (most hardback books are 9.5" tall) = major bummer! We measured (from bottom) 12", 12", 10", 10", 9", 9", 10", 10" with top shelf at 13" from the ceiling.
Arguably the industrial arts class that is most missed is wood shop. Learning how to work with wood is not only handy, allowing you to make and fix things around the house, but allows you to satisfyingly connect with a long history of craftsmanship. Woodworking was one of the earliest skills mankind developed; the pre-industrial world was largely made of wood, and for thousands of years, all men had at least a rudimentary understanding of how to shape and manipulate it. Even up until the second half of the last century, tradesmen and professionals alike had the confidence to be able to build wooden shelves, cabinets, or even chairs for their family.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
I decided to start my own vintage rental company, with farm tables being the main rental item. There was just one problem, I couldn’t afford to buy twenty farm tables… Which led me to my only option, I’d have to build them, except that again I didn’t know a thing about building or power tools nor did I know anyone that I felt comfortable asking to teach me. But, I figured if I could pass the CPA exam, I could figure out how to build a table on my own and learn how to use power tools.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
Back when I was just starting out in my first apartment, I piled up milk crates to store all my worldly goods. It was a simple idea, and it worked like a charm. Fast-forward many years: Faced with a need to store and display lots more stuff, I made plywood boxes in two sizes and mixed them up, adding doors to some and painting the inside backs of others the same color as my wall. The result was a stunning showcase that’s adaptable to any situation and includes useful storage space.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
If you`ve found the diy bookshelf plans below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
Thickness planer. A thickness planer is used to fix surfaces of imperfect wood. If you are picking up less than perfect wood from the lumberyard, wood with some surface defects, a planer will let you fix that wood in the quickest time. A thickness planer pays for itself quick as it allows you to buy cheaper wood that doesn’t have perfect surfaces and fix it yourself. Be careful though. You loose wood during planing. So the remaining amount of wood still has to be worth the price you paid for it.