“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.

Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.


The best advice I could give you is to learn WordPress or find a friend who can help you figure it out. Once the light bulb goes off there will be no stopping you, you will have the power in your own hands to provide what your end user needs and to educate them about the benefits and your products value – in a selfish, wasteful, throw-away society who expect everything delivered yesterday and expect to pay dirt cheap prices for your skills and repetitive hard work. End of rant….Sorry but I just had to comment. I know what it’s like, don’t lose hope! 

And, although a formal education is helpful, it is not necessary, and most woodworkers receive on-the-job training under the supervision of other more experienced workers.  However, because of the ongoing development and modernizing of woodworking machinery, many employers are requiring applicants to have at least a high school diploma, or a few years training in math (specifically geometry) and computer applications.  Many woodworkers will receive training by enrolling in a community or technical college.  Some may attend a university that offers coursework in furniture manufacturing or wood engineering. Individuals who have earned a degree can often move into management or supervisory positions, or go on to open their own woodworking shop.  Becoming a skilled woodworker can often take years, and knowledge of blueprints and work sequences takes training and practice.


Do try a couple of things before you start to think that they are difficult or won’t work. It may take some time finding a local place to sell your crafts to. But then that relationship could be worth a long term source of extra income, so why not.. As for selling online, if you are making small crafts, selling is easier than ever before. You can read about selling on Etsy here.
What I like most about my work is the satisfaction of building something useful and attractive, or even beautiful, out of a pile of raw materials. There is nothing more satisfying than when a complex piece, composed of dozens of parts, each one individually handmade, comes together. The thing I like the least is the business side, such as bookkeeping, promoting my business, etc. If you have a mind for business and the talent to create, this would be the perfect combination.
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results. 

5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
I always try to ask my students why they have come to my school. The standard answer is, "I wanted to learn the right way," but frequently the answer is "that I sit in front of a computer all day and don't feel like I do anything at all." Or simply, they are bored with sitting at home every night. These are the people who are really fun to have in class. They have no preconceived notions, no bad habits to break and they usually really appreciate whatever they have made. Many of them go on to make some new friends at the school. Through the years, I have seen many make plans to take another class "if my buddy is going to do it, too."

An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
So my partners and I opened a Woodcraft store that had an established school as a main part of its business plan. What could be better? Come for a class and buy some tools. But when I first presented the idea of a full-fledged school to the corporate people and told them the dollar amount that I planned to do in school tuition sales, they basically laughed at me. A year after we were opened, they finally started to take notice of this whole "education thing" because I had not only met my projections, I doubled them.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
A jointer makes the dges of your material smooth, straight, and square. This creates what’s commonly called a reference edge that you need for additional steps like ripping or crosscutting. In addition to perfecting the edges of your stock you can also straighten faces, called face jointing. Like edges, you’ll end up with faces that are nice and smooth, and dead flat; a precursor to other machining steps.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.
Picture it: eight people with different skill levels, each trying to design a different project (which, by the way, they have no idea how to do) and hopefully cutting some wood by the third class. Meanwhile, the instructor is running from student to student, and then running to the table saw where a kickback has occurred. It is no wonder that at the end of the class not a single thing has been made and most of the students don't come back.

​Every project needs some tools and material to build on. The tools and material you will need in this plan include Miter saw, jigsaw, measuring tape screws and screwdriver etc. We will suggest you take high-quality material for the plan. Read the source tutorial and watch the video tutorial below for more details. Follow all the steps properly to make a nice and strong Rustic cooler. The tutorial explains the procedure for building this awesome gift. Make sure to use the only high-quality material for any woodworking project.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud. 

Just create stunning “professional woodworking projects” with the step-by-step instructions given in a blueprint to participate in 16,000 completed woodworking projects. Just read the simple steps that you should follow before doing it practically, and you will feel confident all the time. With the simple “hand holding” instructions, you can complete the wood project in very little time.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
Though I’d not planned to strike out on my own, in 2012, it occurred to me I had gained the experience and skills needed to do so and financially, it appeared to be a good time to make it happen. Since I had experience in the field, I chose to remain in the church furniture market but focus more on traditional styles. I’d always admired the old, high altars in European churches and hoped to build some myself. Large scale work does require more than one person, and fortunately, I was able to recruit Austin Glidewell to help establish Altare Design, LLC. By this time I’d mastered conventional woodworking techniques and possessed a working knowledge of marketing, website-building, photography, 3D modeling and business tax laws.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.

Picture frames is a very versatile woodworking project. You can make it as simple as you like. A little bit of ingenuity allows you to create several original designs. This is one woodworking project that can never go stale, because you will never run out of ideas to make new designs and also because it is an evergreen item that will always be in demand.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
Woodturning is the craft of using the wood lathe with hand-held tools to cut a shape that is symmetrical around the axis of rotation. Like the potter's wheel, the wood lathe is a simple mechanism which can generate a variety of forms. The operator is known as a turner, and the skills needed to use the tools were traditionally known as turnery. In pre-industrial England, these skills were sufficiently difficult to be known as 'the misterie' of the turners guild. The skills to use the tools by hand, without a fixed point of contact with the wood, distinguish woodturning and the wood lathe from the machinists lathe, or metal-working lathe.

While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started. 

The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using instead a random sanding motion. This will motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.

In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.


The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.

I honestly think this is a complete woodworking package and you should grab this opportunity. If this complete woodworking guide does not perform well or is not satisfying, just send an email to the customer support team to receive a 100% refund. No questions asked. It offers the 60-day rock solid money back guarantee. But I’m sure that Ted’s Woodworking guide will work for anyone and also support your business to get the best results. So don’t miss this opportunity. Grab it before the offer ends.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
I was self taught meaning I gleaned anything and everything I could from books,DVD’s,TV shows like Norm,Roy Underhill and any where else I could pick up information.Even though I had more than 20 years of woodworking I have in the last few years I’ve found a mentor in Charles Neil and now subscribe to his on line Mastering woodworking show. As to taking a class I’m a bit prejudice since I teach a community collage class on woodworking I highly recommend that you take any classes you can afford.

While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.


Make It: Let your child choose a few bright colors to paint his dragonfly. Paint a wood clothespin to be the body and paint two mini craft sticks to be wings. Once dry, cross the craft sticks on top of the clothespin and glue in place. Add googly eyes to the front and glue a strong magnet to the bottom of the clip. Display it on the fridge and your little one will feel very proud.

Next, grab a role of tape to make your rounded corners for the arms and back supports. Do a rounded corner for the two outside armrests, and for both outside pieces of the table top. Create rounded corners for the top of the backrest supports as well(Part H). Cut with a jigsaw and use an orbital sander to smooth the edges. Check out photos in later parts of the project to see the rounded edges.


Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
I agree with your list. My table (cabinet) saw has a router mount built into the table to the right of the blade and it works great. The table is flat cast iron and I can use the table saw fence. I’ve also built an auxiliary fence with dust collection and more features. The only downside is I can’t use a router lift and have to make depth adjustments under the table. To avoid frequent band saw blade changes, I have two: a big one (17″, 2HP, 12″ thick capacity) for typical work and a 9″ bench-top unit that I keep a narrow blade in. I also build radio control airplanes and the small one works great on small stock.
Hand Tools — Three to four hand planes. A low angle block plane, smoothing plane, jack plane and a jointer plane are the most used sizes. With these in hand and some practice, you can go a long time without a planer, jointer, belt sander, and a few other machines. The market now has a few brands that are close to, if not ready, to use off the shelf. I also think the purchase of at least one good hand saw, a few good chisels, some clamps and a card cabinet scraper are necessary for most projects.
Plywood is an essential material for bookcases. It’s strong, affordable and good looking. There’s just one problem: those ugly edges. You can hide edges behind solid wood or moldings, but the quickest, easiest edge solution is a thin strip of wood veneer called “edge banding” ($6 for 25 ft. at home centers). The process couldn’t be simpler: You just iron on the adhesive-backed veneer and trim off the excess.
There are many textures and materials that can be used for crafting. However, for versatile and affordable crafting, you should think seriously about wood crafts. Craft wood is alluring to crafters first because of its affordable price. When it comes to cheap crafts, wood is the best route. The fact that it is cheap does not mean that it is not useful. In fact, wood crafts are easy to put together, paint and otherwise customize. This means that craft wood has endless possibilities. You can use it in home decor, children's crafts, gifts and much more. For the best selection of wood crafts, you are in the right place. Save on Crafts has crates, boxes, wood burning tools, pine cones and more. Save on Crafts is a discount provider of crafting supplies. This means that you can count on the lowest prices possible with every purchase you make through our store.
Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Although this universal admiration of hand skill is appreciated, the truth is, woodworking is no mystery. And fortunately, even if you missed out on taking a thorough shop class in high school and feel ill-equipped to tackle a simple woodworking project, it’s definitely not too late to learn. Here’s a list of some basic skills you would do well to develop. None of these skills require expensive, dangerous machinery or exotic tools. They are the foundational skills every woodworker should know.
Table saws, band saws, and radial-arm saws are examples of woodworking machines that are most often used exclusively in a wood shop because they are far too large and cumbersome to be portable. Even though they're confined to the shop, these workhorses are so useful that it makes sense to complete a woodworking project in the shop and carry the finished piece to the location or job site where it will be used or installed.

Another option is the circular saw mated with a metal guide (known as a track saw ). These systems have quickly come into their own and can deliver exceptional results. They are ideal for both ripping and cross cutting sheets of plywood, but can handle solid stock if it is wide enough. These systems can cost as much as a table saw but they are compact and very portable.
Biscuits (not the kind you eat). When you get into the details of how to build a bookcase, you’ll discover dozens of joinery options. Our editors simplify those options by focusing on biscuit joinery – a fast and easy way to line up all the boards in your project and get on with the gluing and screwing. You’ll also learn a little about pocket screw joinery in our free bookcase plans.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.

I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.

While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
Start by building a base out of 1x or 2x lumber. Make its depth 1 1/2 to 2 in. less than the depth of the bookcase itself. Its height must be 1/8 in. taller than the baseboard molding you plan to install to make sure the molding slips in easily. Set the base into position and check for level right to left and front to back. Fasten it to the wall studs using 3-in. drywall screws [ 1 ]. Also drive angled screws through the inside of the base and into the floor.

Of course, there’s the occasional install, client meeting or photo-shoot, but those don’t happen often enough to be considered a typical day. I should mention that every day brings its share of phone conversations with clients and suppliers. That happens at all hours. Most work days end by 7:30pm, and once I’m home and have eaten supper, I’ll usually put another hour into handling whatever financial, legal or internet tasks are most pressing at the time. Altogether, a typical work day is about 12 hours, and this is 6 days a week. At 2 1/2 years old, the business is still a start-up which is the reason such long hours are necessary.


Last but not least, every shop needs safety measures. Reading all safely requirements for tools is important, but there are also other issues one needs to deal with. First, it is important to use proper eye protection. Accidents do happen, blades crack and wood does go air born. Therefore, if you value your eye sight it is important to wear safely glasses. Second, you also need ear protection. Since many power tools give off a high decibel noise, the ears become damaged over time, which can cause tinnitus. There are many different ear protections on the market so choose the one that works best for you. The final safety measure is dust collection. Dust collection is often overlooked because it tends to be invisible, but it can enter the lungs and, over time, inhibit the air capacity of your lungs.
Thank you for that info. Is there any recommended size for crosscutting? Lets say I purchase a 4×8 sheet of plywood or MDF at my local home center. I have them cut it down to strips of 18×8 (for example). When I get home, if I need to crosscut the 18×8 piece, is that possible on a cabinet saw with a crosscut sled or better with a track saw? Reason I ask, that will most likely be my scenario when I purchase lumber. I would rarely bring home a full 4×8 sheet from the store because it’s easier to transport it in smaller widths. I’m at the point to make some tool purchases, and seeing if I should go solely with a track saw for my scenario or get both? I do have a 12 inch compound miter saw but cutting to size on that with 18 inch depth panels is hard in one pass.
Offer good for one item at regular price only. Limit one coupon per customer per day. Must present coupon at time of purchase. Offer is not valid with any other coupon, discount or previous purchase. One cut or one bolt of fabric or trim "by the yard" equals one item. Online fabric & trim discount is limited to 10 yards, single cut. Excludes CRICUT® products, candy & snack products, gum & mints, gift cards, custom orders, labor, rentals, class fees or items labeled "Your Price". Exclusions subject to change. Cash Value 1/10¢.
×