Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
Upon graduating from high school, I wasn’t sure exactly what career to pursue, but I knew it had to be something that involved creating things with my hands. I’d always had natural talent working with tools, and despite having been an A-average student, I was never fond of conventional academics. Not having better plans at the time, I took one calculus course, got an “A”, then promptly decided two things: I didn’t enjoy college and taking on any debt would force me into a dull, conventional 9-5 job until the debt could be paid off. I didn’t know this back then, but I was pretty much a textbook case of the restless student with the entrepreneurial spirit. Just a few months later, I got the opportunity to accept an apprenticeship at Remmert Studios which was an incredible break. It was a result of reading a local newspaper article about the business, then going to meet the owner. Not many are able to break into woodworking that easily, especially in the high-end market. That company did a lot of contemporary furniture for churches, and being short-staffed, it wasn’t long before I was given a full-time position.While working that job, I was also taking week-long classes at Marc Adams School of Woodworking as time and money permitted. The combination of hands-on work and classroom study allowed me to acquire new skills very quickly. Being at the school also netted an internship opportunity with one of North America’s most prestigious furniture-makers, Michael Fortune.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.

My parents have the space and Dad has the tools -- a drill press, forstner bits and a long workbench were pretty essential. We decided to use countersunk 2x4s as uprights. This eliminated the need for pricey cap/acorn nuts while still leaving the all-thread ends 'protected' on the outside and allowing us to put it flush against the wall without causing damage.
Stiles are 2-1/2″ x 72″, the top rail measures 1-1/2″ x 32-3/4″, and the bottom rail is 2-1/2″ x 32-3/4″”. My favorite way to assemble frames is with a pocket hole jig, but you can also choose to use biscuits, or simply use brads to nail individual face frame pieces into place. I sometimes use that approach for large built-ins, where it may be cumbersome to construct a face frame on-site during the installation process. The school that will receive these bookcases requested that the face frame go all the way to the floor to prevent pencils and other items from rolling underneath. I generally prefer to keep the face frame about 2″ from the floor to lighten the appearance, but this is a stylistic choice. On larger pieces, such as armoires, I like to keep them high enough to allow a vacuum cleaner to pass underneath.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 917 S. Lusk Street, Suite 200, Boise Idaho, 83706, USA and used by permission. ClickBank's role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.
By following the Woodworking Course, Woodworking Classes or Start Your Own Woodworking Business Course, you eliminate mistakes most woodworkers make when working on their first project or starting their first woodworking business. Learn the importance of wood selection, joinery and tool purchases. You will understand how to start and make your new woodworking business successful.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
The most common bench tools in the woodshop are routers and sanders. We have already talked about routers to some extent. Orbital sanders have come a long way from the jitterbug style of old. New sanders leave a better finish, are quieter and last longer. At some point, probably right away, you will want a sander . No one likes to sand. It is tempting to buy multiple sanders to address an unpleasant task. Here again, I point to the hand tools. Learning to use a smoothing plane and a cabinet scraper will reduce your sanding to little or nothing and cut down your overall time to finish a project.
Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)
There are several ways to complete this task, including pocket screws, brads or biscuits. I have used all of these methods, but my preference is biscuits, as they provide adequate strength, excellent alignment, and ease. I generally just place one biscuit in the center of each rail and stile, which provides alignment assistance while not being overly constraining when manual adjustments need to be made to achieve desired placement. After applying glue and biscuits, use lots of clamps to create a gap-free bond between the face frame and carcass.

LuxuryHomeStuff.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, LuxuryHomeStuff.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Clamp two opposing case sides edge-to-edge and mark each dado location with a pencil. Be sure and mark the location of the case tops far enough down on the case sides, so that the tops provide a joining surface for the valance. Next, clamp a straightedge guide across the two sides. Position the guide square with the plywood edge, install a 3/4-in. straight bit into the router and adjust it to cut 3/8 in. deep. Slowly push the router along the guide, crossing both plywood pieces. If you plan to use biscuits to attach the face pieces, cut the necessary slots with a biscuit joiner [ 2 ]. For the tall sides, space the slots about 12 to 14 in. apart. Cut three slots into shelves that are 18 in. long or less, and four into longer shelves. (I cut slots for No. 20-size biscuits.)
Whether you really need your privacy or you just want to add a bit of rustic charm to your home, this tree branch privacy screen is a great DIY project. It sort of looks like a bamboo shade and is really easy to make. You just need a few strips of thin wood and as many sticks or branches as you want to add. Hang it wherever you feel you need a bit of extra privacy.
Hi Eva – Lots of folks rent space in upscale flea markets/craft stores to sell their projects. I have not had to do that yet since I have had good luck selling on Craigslist. BUT< BEWARE that scam artists work Craigslist. When they email you and ask about the "ITEM" rather than the project by name, that's a scam artist, delete them. Do not open them. I have a full time business and my shop time for projects is limited so I don't make a bunch of things. One more tip, lumber is much cheaper at a local saw mill, rather than lumber yards. Check them out in your area.
All things considered, the easiest and most practical way to plane a piece of unmilled wood is to use a router. You can pick up a halfway decent router fairly inexpensively, and the good thing about investing in one is that there’s truly no limit to what you can do with it - planing a piece of wood is just one of a million different things a router can be used for.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
DIY-minded folks, take note. The following websites are chock full of free plans to build tables, storage, beds — you name it. They'll give you the precise information and guidance you need to create furniture that's exactly what you want, for a lot less than what you'll find in stores. Bookmark these and return to them again and again as resources.
Maybe you have a tablesaw and a 13” thickness planer already, but most of us don’t. Be careful not to fall into the trap of feeling like you have to buy expensive machines to build things. When I work with wood, I use only hand tools and love every minute of it. If you learn how artisans worked their lumber before machines dominated the furniture industry, you will find woodworking by hand to be efficient and viable. There are many tried-and-true techniques to expedite the process that free us from feeling like we have to do machine-perfect work by hand. The real key is to use the right tool for the job: coarse tools for coarse work and fine tools for fine work. Still not convinced? Check out my good friend Jim’s story. I hope it inspires you.
I prefer the large size because it will cut the most sizes. Years ago I purchased a medium shoulder plane, but it didn’t cut the larger sized joints, so I sold it and purchased a large shoulder plane so I could cut and trim most sized joints. Most of your traditional woodworking hand tools can be vintage/used, but used shoulder planes can be very hard to rehab and get “square”, so I recommend spending the extra money on a new shoulder plane. See my recommendations in my hand plane buying guide.
There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
×