This is the most fundamental joint in all wood construction. Whenever we have to join a horizontal member (like a chair rail) to a vertical member (like a leg), we need to interlock these pieces at a right angle. By fitting a tenon into a corresponding mortise (hole), we can create a solid 90° joint. Although it may look intuitive to make, achieving a nice, tight fit requires careful technique and practice. There are many ways to make a mortise, but I use a stout chisel designed for that task and simply determine the width of the tenon based on that chisel’s dimension. Cutting the tenon is usually a matter of four straight saw cuts. When you do learn how to lay this joint out properly and cut it to a snug fit, the world of woodworking opens up to you. At that point, you know all the joinery required to build most tables and chairs.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
Dust Collector. A dust collector works at the source of creation. It’s main purpose is to collect the dust right from the place you are cutting the wood. A lot of power tools come with a dust collector extension which allows the dust collector to be attached to them directly. This means a lot less cleaning up for you to do. Dust collectors come in two types, single bag and double bag. Single bag ones are more common.
Substitute “woodworking” for “judgement” and the principle still holds. Classes, videos, books and private instruction are the result of someone, once upon a time, making a mistake and then passing on the knowledge of how to avoid the same mistake to others, then that knowledge can continue to be passed down the line. That can be very valuable for avoiding common errors and really helps many people in their quest for better results.
Please note that many of the links in this post are affiliate links which means I’ll get a small commission if you purchase any of the tools using them. This is what helps support the website so I can continue making free plans for you. Anything purchased on Amazon using the following link:http://www.DIYPETE.com/AMAZON will help support the site. So thank you for your support!
Nightstands are just not big enough for everything: lamp, alarm clock, phone, photos of your kids … so books, magazines, your tablet or your cup of tea ends up on the floor. This shelf unit gives you about 10 times more space for decorative and essential stuff. And its dazzling design will transform your room. Best of all, it’s easy to build with basic tools.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
The shelves fit into dado joints routed into the case sides. Since the shelves were going to be glued and screwed into the dadoes, they couldn't be adjusted later. So I measured my books before I decided how tall the shelves should be. As a rule, a bookcase with shelves between 7 in. and 14 in. apart accommodates most everything. While books generally fit on 8- to 9-in.-deep shelves, I prefer deeper bookcases, so I ripped the plywood to a width of 11 7/8 in.
Basic woodworking tools are different from beginner woodworking tools. For one thing, I don’t like to use the word “beginner” unless I am using it accurately. It’s not a very useful label, in my opinion, because it implies that there are clear-cut and hierarchical steps in your growth as a woodworker. Who wants to return to grade school during his or her valuable shop time? So I only use the word “beginner” when I’m talking about someone who is touching woodworking tools for the first time.
Now install the vertical stiles. Hold each stile against the front edge of the bookcase sides, then transfer the biscuit­slot locations from the sides onto the stile. Cut slots using the biscuit joiner, apply glue to both surfaces, insert biscuits into the slots and press the stile home. Use a rubber mallet to tap it tight. Repeat the glue-and-­biscuit routine to attach the horizontal mahogany aprons to the shelves. Prior to installation, I routed a decorative profile along the bottom edge of each apron to create shadow lines that accentuate the shelves. The aprons are more than decorative, though. They stiffen the shelf to prevent sagging. Trim the top of the bookcase with crown molding [ 8 ] and the bottom with base molding [ 9 ]. Wait 8 to 10 hours for the glue to cure before filling the shelves.
Plywood shelves are simple to cut, but look a little thin and can sag over time under the weight of books and other payload. I like to apply a solid hardwood strip of at least 1″ thick to strengthen the shelf and give it a more robust appearance. Cut four strips to 3/4″ x 1″ x 36-1/4″ (slightly longer than the shelf itself, allowing you to trim flush later). I attach this strip by simply gluing and carefully clamping for good alignment, gluing the 1″ thickness to the plywood. In the past I have also used biscuits or brads for attaching the strips, but I have found it to be unnecessary, and the method I currently use delivers great results every time. Use a lot of clamps to ensure a good bond between the plywood and edge strip. Carefully force each surface flush as you move from clamp to clamp. If you are careful here, you can save yourself a lot of sanding effort later.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
×