My trusty old radial arm saw is much preferred and the “go to” tool over a table saw. Yes, I realize many question why anyone would ever need a radial arm saw, much less prefer one over a table saw, but I grew up using one and use it for all sorts of projects. I do have a table saw but only use it when I have to when ripping large stock that I can’t get with my radial. Of course all woodworking tools demand respect to avoid serious injury, but my experience is that a table saw demands far more than my good ole reliable, supremely versatile, radial arm saw. Given a choice between one or the other, I’d pick the radial every time.
The table saw is the center of most workshops; it is the largest and most imposing tool in the shop. While it is an important tool, one could claim that table saw need not be on this list. However, it is an important tool and shows that creating a shop is not a matter of just collecting hand tools. There are jobs that hand tools cannot do as well as tools like the table saw, especially when there is such a wide variety of blades which can be set up and changed for so many different applications. Table saws create straight and consistent cuts. When setting up a table saw for a cut, one needs to set the depth of the blade and adjust the fence according to the width desired.

​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.


Keeping your house clean and well-sorted is probably one of the trickiest tasks, especially if you are one of those people who have more books than clothes and shoes combined. Each of your books is priceless and you want to preserve them in the best condition possible. But it is not always so easy, especially if you do not have a proper bookshelf. Now bookshelves do not come cheap, be it a simple plywood one or an ornate wooden case. So, here are forty simple yet trendy DIY bookshelves for you and your books.

Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.


Work bench. You might get by by using a saw horse as your work bench for a while but believe us when we tell you that you need a dedicated sturdy work bench for doing your woodwork. You can buy one, or like many woodworker, make one yourself. You can make your own workbench for under $200. There are plenty of free videos and guides online that will show you how. Just type your search in a search engine.
Even though I have many large power tools I am still a fan of hand tools, in particular, planes and chisels. In many applications I have found they are the fastest means to an end. Other factors in their favor are their cost. Good hands tools are not cheap, but compared to their motorized counterparts, they are usually much less costly. Another is space. Besides taking up far less space in the shop, they often require less space to use. Think of edge joining an 8 foot long plank. On a jointer you need a minimum of 16 feet of work space. With a hand plane, you move the tool, not the material, so you only need slightly more room than the length of the material.
After investing a number of weekends building a nice table or chest, how are you going to finish it? Finishes beautify and protect the piece you’ve worked so hard to build so don’t cop out and do the “rub it with oil” thing. There are so many beautiful finishes that become second nature to work with. I use shellac 99% of the time. Once you get the feel down, it’s really quick to apply, very forgiving, easily repairable, and you never have to clean a brush (because it re-softens in alcohol)! There are other varnishes that provide good protection for outdoor use as well. I recommend picking up a good starter book, like Jeff Jewitt’s Hand Applied Finishes. It is simple and straightforward, without getting too far into minutiae.
Work bench. You might get by by using a saw horse as your work bench for a while but believe us when we tell you that you need a dedicated sturdy work bench for doing your woodwork. You can buy one, or like many woodworker, make one yourself. You can make your own workbench for under $200. There are plenty of free videos and guides online that will show you how. Just type your search in a search engine.

As your experience grows, it is typical to look for the next upgrade, which is often a bigger tablesaw, a miter saw, a small jointer, or a small planer. As I see it, if you own a decent contractor saw, a bigger, heavier cabinet saw won't give you much more than what you already have. The quality of cut will only be marginally better. I would look to spend my money elsewhere.
Hi there, I'm glad that you are here. Firstly, let me introduce you that my name is Kevin Smith and I'm a coffee addicted guy, a blogger. Secondly, the reason why I create this website is to analyze what's the best products on the market with high quality and affordable price so that I make a decision to buy the right products for my family, friends and me. Thirdly, I just want to learn more about Home & Improvement Tools and Appliances so that I could improve my sweet little home.
If a woodworker wishes to advance in the field or to demonstrate competence in the industry, they may also choose to become licensed. The Woodwork Career Alliance of North America offers a national certificate program. The AWI, or Architectural Woodwork Institute sets standards for the industry and offers training programs for management and mid-management positions.

The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
If you are wanting to build great looking chairs for your patio you've come to the right place. I bought a home late last year and didn't have any patio furniture whatsoever. My dad had built a beautiful piece for their home and so I credit him with design help and the inspiration to build my own. This setup is perfect for enjoying a relaxing evening out on the deck with friends or family. I built my chairs out of cedar because cedar does not rot and stands up against the outdoor elements quite well. You can use pine as long as it is painted or coated with a thick finish of poly.
In being self-employed, one day will greatly vary from the next, but generally, I start in the morning by dealing with in-town errands or head right to the shop if there are none. Once at the shop, there’s an e-mail check, then a brief glance at various websites to look for new developments related to our market and clientele. Then the real workday starts. I’ve got a bunch of notes regarding current projects taped next to my computer and will make a list for the day’s tasks by picking the highest priority items from the notes. The goal is to get that stuff accomplished by the end of the day. There are two of us in the shop, but we usually work on separate projects, so that’s why I have my own to-do list. Some days are spent on the computer designing or creating programs for the laser or CNC. Other times we’re doing runs of sunglasses or guitar parts which we sell wholesale to other businesses. In which case, I may be operating the laser or CNC. Despite the high-tech tooling, there’s still a lot of bench work to do, and that can involve cutting and fitting joints with chisels and hand planes. Besides that, there’s always plenty of rough lumber to mill since no project can begin until boards are flattened, surfaced and cut to dimension.
My trusty old radial arm saw is much preferred and the “go to” tool over a table saw. Yes, I realize many question why anyone would ever need a radial arm saw, much less prefer one over a table saw, but I grew up using one and use it for all sorts of projects. I do have a table saw but only use it when I have to when ripping large stock that I can’t get with my radial. Of course all woodworking tools demand respect to avoid serious injury, but my experience is that a table saw demands far more than my good ole reliable, supremely versatile, radial arm saw. Given a choice between one or the other, I’d pick the radial every time.
Thank you for sharing your story! Would love to hear how you got started with your blog and business too someday, I always find it so interesting what inspires people to shift their career path. I can’t believe you’ve learned so much with YouTube videos! And congrats on creating such a successful business from scratch and also having the courage to walk away when you knew it wasn’t for you anymore. We’re having a home built next year, so look forward to checking out all the custom work you’ve done with your place!
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
Whatever your dream for a rustic look, you are sure to find something in this collection that will help you along. Many of these projects are so easy to do and you can complete them in less than a day. Some make wonderful gifts as well so if you know someone else who just loves the country, rustic look, make them something to brighten their own décor. The projects use all sorts of materials, many of which are really inexpensive or even cheap in some cases.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Dad was SOOO concerned that there wasn't any way they weren't going to go rhombus and kept trying to over-engineer the project (my husband wasn't so certain, either!) but I stuck to my guns and followed the plans I'd "modified" to my specs -- 92" uprights (so as not to actually wedge against the ceiling), with 3/4" washers plus lock washers and plain old hex nuts in a 1" wide hole countersunk to 1/2" depth, 1x10 shelves and my brother just happened to have salvaged massive amounts of 1/4" all-thread that Dad cut to 12" lengths for us.
Ted’s Woodworking is the revolutionary program that will help you complete the wooden projects by following simple techniques and woodworking plan to make everything possible just by spending few minutes for having the best results in a faster way. You can skip the problems by following the simple step by step instruction to understand the concepts of building woodworking projects quickly. It will explain it to you with diagrams, important parts without confusing you. The creator spent almost 40 years to collect the required information from the world’s comprehensive collections of woodworking, plans to make you feel comfortable to build the things that you want forever.

Whether they’re just getting started, or have been involved with woodworking for a while, many woodworkers wonder what woodworking power tools they should add to their shop. The answer to this question can be subjective, and depend on what types of woodworking projects you commonly build, but George Vondriska is ready to provide you with his opinion on which five woodworking power tools should be considered top tier tools for your shop.
If you`ve found the diy bookshelf plans  below interesting we invite you to check various other free woodworking plans, we have curated lists that will show you how to build a router table, duck house, deer stand, bat house, tiny house, rocket stove, diy tree house, cat tower, garage, fire pit, porch swing, greenhouse, small cabin, farmhouse table, pole barn, rabbit hutch, diy dog bed, a playhouse, a chicken coop, a coffee table or a gazebo.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
If you have wood pallets just lying around the yard, put them to use by turning them into a great mud room bench. This bench would look fabulous on the deck or just inside the door, wherever you want to put it. When you finish putting it all together, just sand and stain it whatever color you want and you have a beautiful bench that cost you very little to create.

Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Any bookcase you build should be anchored to the wall so it can’t tip over and injure someone. Simply screwing it to wall studs is one good solution. If you choose that method, load up the bookcase with books so it fully compresses the carpet before you drive the screws. If you want to be able to move the bookcase without removing screws, pick up a couple of chain latches. Fasten the chains to studs with 2-1/2-in. coarse-thread screws. Position the tracks so there will be just enough slack in the chains for you to detach them.
One great aspect of Teds Woodworking is that it is easy to understand! You will find all the projects and a way to learn how to build them with an easy step by step procedure. These plans and structures are already proven to work. Some guides out there will only give you lousy plans and waste your time. Teds Woodworking offers simple guides and schematics. This system has blueprints for almost everything you want to make. There are available blueprints from dog houses to green houses. Even instructions for building gazebos and guitars are easy to follow. The instructions on how to create children’s and baby cradles are carefully laid out in a way that you can easily build them right away.
Bench top machines have come a long way with respect to dust collection. Most now have ports that connect to a shop vac. For a few dollars you can buy a switch that will automatically power up the shop vac when you turn on the tool (such as a sander). When you turn off the tool, the switch will allow the shop vac to run a few extra seconds to clear the hose and then shut off.
You really don’t have to do anything to get a great set of coffee tables. Well, you do have to gather a few tree trunks or stumps. Just sand them down a bit, and cut them off to make them flat. You can have a collection of different sizes sitting around the room and in different shapes. Stain them if you want but you can leave them natural for a really rustic look.

You can do this with a dado blade, or alternatively, you can simply make two passes with a standard kerf table saw blade. I often do the “two pass method” for 1/4″ dado and rabbet cuts simply to save time, avoiding setting up a dado blade. Set up a sacrificial fence on your table saw because you will be spinning the blade right next to the fence. Set your blade height to 3/8″, and remove a width of 1/4″.


The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
In recent years, this versatile and accurate tool has become a fixture in the work shop and at the work site. Also called a “chop box,” the miter saw consists of a powerful circular saw mounted on an arm that hinges at the rear of the tool. When the blade is lowered in a chopping motion, it cuts through the workpiece, passing through a slot in the base. The motor and blade can be pivoted with respect to the base for miter cuts. Another adjustment makes it possible to tilt the blade, too, allowing for compound miter cuts, handy for jobs like cutting crown moldings, which are set at a pitched angle and that must also turn around corners. The diameter of the blade determines the maximum cut width, with standard sizes ranging from 8-inch blades up to 15 inches. A 10- or 12-inch saw is sufficient for most jobs.
How about building a secret room hidden behind a door that’s masquerading as a bookcase—just like in the movies? Not sure how to build the entrance? Well, just buy a kit. These bookcase doors from Woodfold Manufacturing are perfect for disguising the secret entrance. The bifold-style doors look like a typical bookcase when they’re closed. In fact, you can even load up the shelves with 500 lbs. of books or knickknacks. The doors slide open along a steel roller system at the top and the bottom to reveal the secret room.

Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
At the same time, in order to improve your skills, you have to first use those skills and will make mistakes as a novice. How quickly those are overcome and improved on varies from person to person. Some craftsmen grasp a skill quickly and progress to higher levels, others, for several reasons, take more time. Those that do this quickly thrive as self-taught artisans.
There is a seemingly endless selection of power tools. Variations of tools that were only seen in large cabinet shops and furniture factories can now be found at the local big box hardware stores. Prices are lower today than they have ever been in terms of real dollars. Quality can vary and old brand names don't always mean what they used to. So where do you start?
×