WoodSkills and Norman Pirollo offer online woodworking classes, woodworking plans, video lectures and woodworking tutorials. The classes and courses provide detailed and comprehensive step by step sequences for woodworking skill-building. Each woodworking class and tutorial is based on actual furniture making expertise. As founder of  White Mountain Design , Refined Edge Design , WoodSkills and Pirollo Design, I bring to you two decades of knowledge in furniture making. In recent years, I have authored three woodworking books:
 This bookcase plan is designed to be large enough to handle all of the books belonging to the voracious reader in your family, virtually indestructible to withstand years of abuse, and easy on the pocket book using inexpensive materials from your local home center. For about $100 you can have a bookcase that would cost $600 – $800 at a retail furniture store. 

On both the belt and disk sanders, the workpiece is presented to the tool (the opposite is true of portable belt and hand-held disk sanders which are presented to the work; as a result, they are particularly useful in sanding oversized workpieces). On stationary sanders, an adjustable worktable or fence can be fixed in front of the sander to position the workpiece during sanding. Belt sizes vary greatly, with four-inch wide, two- or three-foot-long belts being usual, as are four- to eight-inch diameter disks.
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
Formally known as a “tilting arbor saw,” this tool is just an upside-down electric handsaw that’s been mounted to the underside of a steel table top, with the circular saw blade protruding through a slot. The “arbor” is the shaft on which the blade spins. It’s an axle that can be tilted with respect to the horizontal table top for cutting angles; it’s raised or lowered to adjust cutting depth. A miter gauge enables the sawyer to push stock at angles or perpendicular to the blade (“cross-cutting”). A fence can be fixed parallel to the blade for cutting along the length of a workpiece (“rip-sawing”).
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily.
A very very interesting woodworking project you can undertake is to make spoons and ladles of all sizes out of wood. These items are really coming back in a big way. I sincerely feel you can attract a lot of attention and sell these items very well. People are beginning to use more wholesome utensils in the kitchens. Wooden spoons and ladles are going to be raging popular products. Getting a lathe will go a long way in making any kind of wood bowls, spoons and ladles.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!

But what if you want to make a box? The revered (and overly-mystified) dovetail joint is a very strong way to join corners of boards. Of all features that non-woodworkers admire today, the dovetail joint is the one that creates the most awe. It is composed of one side cut into wedge-shaped “tails” that mate into corresponding “pins.” When fitted together, the wedge shape prevents the boards from sliding apart in one direction. This joint has been very standard construction since the 1700s. Never meant to impress, it was usually intentionally hidden behind veneer, molding, or paint so that no one would have to look at that “ugly” joinery. It wasn’t until the arts and crafts movement that visible joinery was considered an aesthetic asset. Today, making dovetail joints has become a litmus test for serious woodworkers, but don’t let this scare you away from trying it. Check out a few of the four million “How to Cut Dovetails” videos online and then get into the shop. It’s much more straightforward than people think: Cut tails. Trace the tails on the other board. Then cut out the waste you traced. That’s pretty much it. All the fine tuning is just practice.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
Make It: Paint nine craft sticks red, six craft sticks white, and four mini craft sticks white. Let them dry. On a rectangle piece of cardstock, have your child create a blue sky and green grass with colored paper or markers. Then help her create the bottom of the barn by gluing on a row of 11 craft sticks vertically in the following pattern: two red, one white, five red, one white, two red. Glue white sticks horizontally along the top and bottom and cross two in the middle as shown. Glue the mini craft sticks to red cardstock to form the barn roof. Adhere the barn roof to the background above the barn. Cut out a rectangle from black paper and adhere it to the barn. Cut strips from a paper bag and crumple for the look of hay; adhere to black rectangle.

Fifteen years ago, I was running a small woodworking school in a funky L-shaped room with a leaky roof (try keeping a straight face when water is dripping on your head while you demonstrate how to use the table saw). As much as I liked working at the architectural millwork firm, I realized the school would always take a back seat to the main focus of the business.
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Another option is the circular saw mated with a metal guide (known as a track saw ). These systems have quickly come into their own and can deliver exceptional results. They are ideal for both ripping and cross cutting sheets of plywood, but can handle solid stock if it is wide enough. These systems can cost as much as a table saw but they are compact and very portable.
My own organization is crucial to the success of a class, especially with an advanced project class. If I have not examined each operation we need to do, in what order we will do it in and, most importantly, how many operations we can do simultaneously, then we will get very little done and the project will not even be close to finished in the time allotted.

To start off you only need either a 1/4″ or 3/8″ mortise chisel (or some size close to those). You don’t need a whole set of mortise chisels. Mortise chisels (also spelled “mortice”) are used for chopping mortises (rectangular holes) into the side of your board for insertion of a tenon. “Mortise and Tenon” is a very common and very strong joint that most people have heard of.


This is the most fundamental joint in all wood construction. Whenever we have to join a horizontal member (like a chair rail) to a vertical member (like a leg), we need to interlock these pieces at a right angle. By fitting a tenon into a corresponding mortise (hole), we can create a solid 90° joint. Although it may look intuitive to make, achieving a nice, tight fit requires careful technique and practice. There are many ways to make a mortise, but I use a stout chisel designed for that task and simply determine the width of the tenon based on that chisel’s dimension. Cutting the tenon is usually a matter of four straight saw cuts. When you do learn how to lay this joint out properly and cut it to a snug fit, the world of woodworking opens up to you. At that point, you know all the joinery required to build most tables and chairs.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
There are some who also swear by their bandsaw for ripping lumber. A bandsaw can cut faster and is far safer to use than a tablesaw. I personally still prefer to use a tablesaw for ripping for two reasons. First, the bandsaw table and fence are smaller than a typical tablesaw. I find this makes it harder for me to keep a straight edge. Second is the quality of cut. A bandsaw rip will usually be rougher than a tablesaw rip.
Learn woodworking from a home computer, tablet, or smartphone. Woodworking video lectures can be followed sequentially or in any order. The lectures can be repeated to reinforce what you have learned. Flexibility in learning allows you to speed your woodworking knowledge. Learning the essentials of woodworking accelerate your learning curve to become a woodworker
If you have an old cabinet or dresser that you can redo, consider taking out the drawers and just adding rustic wooden planks. This gives the entire cabinet a great rustic look and it is really easy to do. This is a great project for those old dressers that have broken or missing drawers. You can attach the wood pieces together and fix them so that they pull out for easy access to the dresser contents.
Before you put any tool to your lumber, you will need to understand its proper orientation and what direction to plane the board. As trees grow, growth ring layers continue to build on one another and this produces beautiful grain that shows in our boards. This grain can make planing it trickier if we ignore the ideal direction to work. Working wood grain is kind of like petting a cat — if you go from tail to head, you will find the hair standing straight up and might get a hissing disapproval, but if you pet “with the grain” from head to tail, you’ll find the hairs lay down nice and smooth and purring will ensue.

The Nine-month Comprehensive is designed for aspiring professional furniture makers and dedicated amateurs who seek in-depth training at the highest standard of excellence. The hands-on, project-oriented format includes the full range of furniture making skills. Sequential projects take students from the fundamentals through the fine points of design and craftsmanship.

5. Reading technical drawings: In order to make the furniture projects by our furniture plans, you should have the basic knowledge of technical drawing, so you could read drawings of the parts and assemblies. We do not stick strictly to exact rules of technical drawing in our plans; instead, we have adjusted the content and appearance of the drawings and plans, so they can also be understandable to the less experienced woodworkers.
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.

Made this bookshelf with a little alterations. I made it 8'x8'. There was no cutting involved because I bought 8' 1x3's. There are 8 shelves of slightly varying heights. If I did it again I would have about 12 shelves on the 8' but we will stack on this. I stained it using a poly-stain. Thought this would take less time. I will never use this again. It left drips all over the place..even though I was being careful. I would have been better off using stain then polyurethane. I also made the mistake of bying oil based (rushing in the store). Didn't realize until I went to wash my hands. If you ever do this...I found out that cooking oil followed by dishsoap works great to take oil based paints off your hands. I also used 5/16" rod because there wasn't any flex and I was making the shelves so big (used a 5/16" drill bit too so the fit was a little tight :) . Couldn't find the acorn nuts after 4 stores so I ordered them on Ebay ($10 inc shipping for a box of 50). Only put them on front because I needed 64. I also put metal cable on the ends (drilling two holes at the end of each shelf and x'ing it) so the books wouldn't fall off (got this idea from the poster who used clothesline). It cost a little over $200 when done (CT prices are high) but it is much sturdier than a Melemie shelf that would have been this price. My husband did not not believe it wouldn't "rack" but it is VERY sturdy. Will be making more.
To reduce the risk of personal injury and property damage, read and follow all related product manufacturers instruction manuals and information before performing any of the applications shown. Some construction-related applications shown may not be allowed in your local area. Consult your local authority having jurisdiction (AHJ) before starting work for information on permits, applicable codes, and other regulations. Black & Decker disclaims any responsibility for any damage to property or injury to persons as a result of misuse of the information provided.
Woodworking knowledge is something we are all constantly in pursuit of. Thankfully, there are a LOT of options available to us. We no longer have to rely on taking expensive classes when so much information can be found online and in books. And as many Guild members know, even online classes can be quite effective thanks to the additional interactivity. In my situation, most of my learning is through podcasts, books, and blogs. I punctuate my learning each year by taking a class or two. And whenever possible, I do try to learn directly from other woodworkers in person. So if you’re like me, you probably want to select more than one thing in this list. Let’s just say you should pick the one that you get the MOST information from. And if you are thinking about podcasts, just select the Woodworking Blogs option, since most podcasts are presented on blogs.
Hardwood boards and softwoods may look similar in shape and dimension, but they are sold using completely different measuring systems. Softwoods are typically sold in standard lumber dimensions (such as a 2x4), whereas hardwoods are most often sold by the board foot. Calculating board feet helps you guarantee that you're getting your money's worth on every piece of hardwood you purchase.

Dust Collector. A dust collector works at the source of creation. It’s main purpose is to collect the dust right from the place you are cutting the wood. A lot of power tools come with a dust collector extension which allows the dust collector to be attached to them directly. This means a lot less cleaning up for you to do. Dust collectors come in two types, single bag and double bag. Single bag ones are more common.
×