Multiples of these bookcases can be connected to form a single, larger unit, generally for a built-in application. To do so, simply build them without a face frame, and finish boards that can be used to construct the face frame separately. Then, nail the face frame in place using brads after the cases are installed. To improve the appearance of the face frame joints using this approach, mill the rails (horizontal pieces) so that they are 1/8-in thinner than the stiles (vertical pieces). This creates a nice shadow line and conceals any unevenness at the joint. Also build a single long top to tie all the pieces together. I use plywood with biscuits to span beyond 8″, edge banded with hardwood strips as you have done for your shelves.
Measure back opening (the plywood sits between the protruding outside edges of the sides that were formed from the rabbets that were previously milled, and fully overlaps the backs of the carcass top and bottom panels). Cut 1/4″ plywood to fit snugly. Even though I have a large cabinet saw equipped with ample outfeed support, I like to make the cross-cut first using a circular saw for a safer, more controlled operation, and then rip to width on a table saw. Be careful when cutting 1/4″ plywood on a table saw, as it can flex, allowing the material to rise above the blade which can cause a dangerous kickback. Use a slow feed rate, apply steady downward pressure when needed, and be sure to use your blade guard for this operation.
It’s mostly been learn by doing for me. I can’t afford to go somewhere to take any lessons. However, I do learn from books, DVDs, and videos on the internet. I still believe that learning by doing is the best way. Books and videos can get you going in the right direction but when you do it on your own all kinds of problems crop up that you have to solve. For example, when woodcarving the best way to understand what carving with the grain is is to carve with a carving tool. Same thing about sharpening a carving tool. You had better learn how to sharpen by sharpening your tools when they need it. You’re dead in the water if your carving tools are not sharp.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
One of my mentors started out as a cabinetmaker who loved working wood but dreaded getting to the finishing part. He started doing some digging to learn more about it and became so addicted to the process that nowadays he loathes having to build anything because all he wants to do is the finishing! I promise that if you give a little energy to learning how to properly finish your work, your enjoyment of the finished piece will be dramatically increased. These final touches are enough to inspire you to take on another project.
LuxuryHomeStuff.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, LuxuryHomeStuff.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
The old saying "If only I knew then what I know now" certainly applies to buying woodworking tools . Like nearly every woodworker, I would love a large shop equipped with all the best tools. Like most woodworkers however, I have had to make choices due to finances, space, and what was available at the time of need. As I look back at the purchases I made over the last 30 years, I have few true regrets, but there are many things I would do differently. Here is how I would approach equipment selection today.

Fifteen years ago, I was running a small woodworking school in a funky L-shaped room with a leaky roof (try keeping a straight face when water is dripping on your head while you demonstrate how to use the table saw). As much as I liked working at the architectural millwork firm, I realized the school would always take a back seat to the main focus of the business.
Storage can never be enough for a home with children. Especially if the family is midsized to a large one! A headboard with optimum storage space is an ideal solution in children’s room to accommodate most of their belongings, so that they can have an easy access to them on a daily basis, and not litter them everywhere. The headboard can be revamped for them, according to their choice of colors and need.
I know I’ve been a little MIA but we’ve had a big project in the backyard, an overwhelming workload (which we planned on being MUCH less), and then decided to hire out for some help to haul away a huge amount of dirt.  Unfortunately, that ended up with the guy we hired stealing from us…..uggggh.  When will we ever learn to not be so trusting?!  Steve and I both have a problem with that……but when did being “too trusting” become such an extreme character flaw?!!  Sad.  Anyway, the whole situation is under investigation and there are some definite twists to the story that the crime-show-watcher in me would love to share with any other crime-show-watching enthusiasts out there. ;) Hopefully soon.
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
Storage can never be enough for a home with children. Especially if the family is midsized to a large one! A headboard with optimum storage space is an ideal solution in children’s room to accommodate most of their belongings, so that they can have an easy access to them on a daily basis, and not litter them everywhere. The headboard can be revamped for them, according to their choice of colors and need.
In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.
DIY-minded folks, take note. The following websites are chock full of free plans to build tables, storage, beds — you name it. They'll give you the precise information and guidance you need to create furniture that's exactly what you want, for a lot less than what you'll find in stores. Bookmark these and return to them again and again as resources.
Hello Eva. Thank you for commenting. I know and feel what you are saying. But selling is an integral part of any business and there is no escaping it. There are no companies as such that pick up things from artisans and craft persons. But it might not be difficult to find a business or a store where you live that will do just that. And maybe other ways of selling your wood crafts are worth looking into as well. Here is an article we wrote on it… Easy places to sell more of your wood crafts..
Preparation is everything. It took my friends a long time to learn that dropping by on their way home from work to hang out was not a really good time for me to stop and shoot the breeze. I typically spend a minimum of one hour and usually two or three hours setting up a three-hour class, going through all the operations I plan to cover that night such as getting the lumber milled, making sure the tools are in good working order and doing any of the critical machine setups in advance with no distractions.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.

Getting started in woodworking can seem like a daunting task. From specialty woodworking tools to identifying and understanding the different types of wood, there is so much to know that even the old-timers are still developing. But learning and experimenting are what woodworking is all about. Get started on the right foot with some essential basics about safety, tools, lumber, and traditional layout and measuring techniques.
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.)   So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.

If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
An old piece of wood and a few hooks will help you to create a beautiful hanger for your favorite coffee cups. Just add the hangers, stain the wood and then hang it on the wall. This is a project that takes little time and will cost very little if you already have the wood on hand. You just have to purchase the hangers which are relatively inexpensive.
The band saw is great for freehand and curved cutting, but its depth of cut also makes it suitable for sawing thick lumber. The table tilts on many models, allowing for angle cuts. Band saws come in many sizes but for most home workshops a good choice is a 12- or a 14- inch model (the dimension indicates the size of the workpiece that can be presented to the blade; a 12-inch band saw will saw to the center a 12-inch piece).
This is the most fundamental joint in all wood construction. Whenever we have to join a horizontal member (like a chair rail) to a vertical member (like a leg), we need to interlock these pieces at a right angle. By fitting a tenon into a corresponding mortise (hole), we can create a solid 90° joint. Although it may look intuitive to make, achieving a nice, tight fit requires careful technique and practice. There are many ways to make a mortise, but I use a stout chisel designed for that task and simply determine the width of the tenon based on that chisel’s dimension. Cutting the tenon is usually a matter of four straight saw cuts. When you do learn how to lay this joint out properly and cut it to a snug fit, the world of woodworking opens up to you. At that point, you know all the joinery required to build most tables and chairs.
Bruce Lamo has done woodworking pretty much all his life, although never exclusively to make a living. He prefers making furniture and working with solid wood, but often uses plywood when making cabinets. This article originated when a few friends were considering buying tools that based on his experience, he thought would not be a good investment.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood.

In this age of air-powered nailers, drills, sanders, impact wrenches, grinders, saws, spray guns, washers, and other pneumatic tools, the compressor has become a virtual necessity. The compressor consists of a motorized pump; a tank for storing the compressed air; an on/off control (governor) that tells the pump when to start and stop in order to keep the pressure within preset limits; and a regulator to control the pressure at which the air escapes the tank to suit the needs of the tools being used. There’s a metal frame on which all the parts are mounted, usually with a carrying handle and sometimes wheels.


When many people hear the word woodworker, the image of someone leaning over a workbench sanding a long piece of wood with his or her hands. However, modern woodworking requires training on highly technical machinery, such as CNC (computerized numerical control) machines.  Even woodworkers caught somewhere between modern equipment and a hand planer typically use CNC machines to fabricate large or intricate products.  If working for a large company, a lot of the work will be done on an assembly line or in various areas on the floor designated to complete a particular part of a project.   The tasks will be handled by different workers with very specialized training on each machine. For example, one machine might cut a large piece of wood into three sections, whereas another machine might take one of the sections and round each edge.
oh yeah, and buying a bunch of cap nuts is not so easy unless you order ahead of time. i went to two hardware stores (one family owned and one big box) and they kind of laughed at me when i said i needed 32. so i got regular nuts, tightened them so they were flush with the all thread on the front side, hammered it against the board and tightened the back side while holding the front one in place with a wrench. so, some of them have a little bit of overhang on the back side, but i don't have to worry about gouging skin while walking past it. for my next set, i'll order the cap nuts in bulk from ebay ahead of time...
Disclaimer: I've definitely taken a route that favors hand tools. More so than say, the 'modern' approach -- and it's mostly because, having used both awesome power tools, and awesome hand tools, I find that I enjoy the process of the work more with hand tools (I can actually chat with someone while I'm using hand tools -- not so much when I'm running a circular saw, router, sander, band saw, table saw, etc.)   So, my take is going to be biased towards a more 'traditional' approach -- but the resources and people listed below are no strangers to modern tools either, and definitely make use of them when they choose.
Even if you don’t live in a rustic log cabin, you can give your home a great cabin look by simply planking one or more walls. This is a relatively easy project that will add beauty and value to any home. Just choose the wall that you want to change, and add wooden planks which you can pick up at most home improvement stores for very little. Then stain if you want and you have a lovely cabin type wall
Hello everyone.for a less expensive turning tool, I use a mini lathe for small turning projects..up to 10″. The smaller projects I have in mind are mini baseball bats, lamp bases, smaller bowls, candle stick holders, and the list goes on and on. my favorite turning projects are pens. I make over 100 different types of pens and pencils from inexpensive wood from all over the world..once you start turning on a lathe…you’re hooked..have fun.
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
· Each plan contains a clear and colourful scheme, so no guessing is required. It depends on the level of detail; the most demanding projects will take you to the park! If the instructions are clear, the project is built on its own. All pieces are “clicked” and put in place. It is also suitable for beginners. A skilled woodworker can complete the project in less time than usual ones.
Arguably the industrial arts class that is most missed is wood shop. Learning how to work with wood is not only handy, allowing you to make and fix things around the house, but allows you to satisfyingly connect with a long history of craftsmanship. Woodworking was one of the earliest skills mankind developed; the pre-industrial world was largely made of wood, and for thousands of years, all men had at least a rudimentary understanding of how to shape and manipulate it. Even up until the second half of the last century, tradesmen and professionals alike had the confidence to be able to build wooden shelves, cabinets, or even chairs for their family.

Multiples of these bookcases can be connected to form a single, larger unit, generally for a built-in application. To do so, simply build them without a face frame, and finish boards that can be used to construct the face frame separately. Then, nail the face frame in place using brads after the cases are installed. To improve the appearance of the face frame joints using this approach, mill the rails (horizontal pieces) so that they are 1/8-in thinner than the stiles (vertical pieces). This creates a nice shadow line and conceals any unevenness at the joint. Also build a single long top to tie all the pieces together. I use plywood with biscuits to span beyond 8″, edge banded with hardwood strips as you have done for your shelves.

​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Having very sharp tools is one of the most important aspects of proper traditional woodworking. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
×